2-Way Waste Manifold - 12' Cable - 3/4" Ports This manifold manages waste from multiple drains with intelligent control built in. A compact automatic system handles waste drainage from the two outlets. Must be used with Gulper® IC. The two-way manifold IC is connected to a Gulper® IC. When the manifold senses water, it sends an electrical signal to the Gulper® IC, which evacuates the system. As the water level decreases, the electrical signal transmitted by the manifold will cease, and the Gulper® IC will continue to operate for a further 15 seconds before turning off.  IC – Intelligent Control Technology At the heart of every Whale IC product lies innovative electronic control circuitry built in. This enables the IC sensor accessories to communicate directly with the IC pumps to control the performance. These accessories send signals to built-in intelligent software, which then controls the pumps to react as required. Specifications: Cable Length: 4m (12ft) Inlet Hose Connections: 3/4" (19mm) Outlet Hose Connections: 3/4" (19mm) Control Voltage: 5V dc via Gulper® IC Current Draw: Low power 0.01 Amps supply Connectors: Deutsch® Connectors: Quick Connect Series 7 ways (directly onto Gulper® IC)

2-Way Waste Manifold 6' Cable 3/4" Ports The 2-way manifold with Whale Intelligent Control built-in. The IC manifold can be used with a Whale Gulper pump to create a grey water disposal system. The manifold accepts two waste inputs and senses water through the wall. This relays information to the Gulper IC pump to turn on and pump the wastewater.

2-Way Waste Manifold 12' Cable 1-1/2" Ports 2-way manifold with Whale Intelligent Control built in. The waste manifold can be used with a Whale Gulper pump to create a greywater disposal system. The manifold accepts two waste inputs and senses water through the wall. This relays information to the Gulper IC pump to turn on and pump the wastewater. This Whale WM3884B IC manifold has 12 feet of cable and 1-1/2" ports. Specifications: Height: 115mm (4-1/2") Length Cable: 12' Cable Voltage: 12V - 24V DC Width: 139mm Hose Size Outlet: 25mm (1") & Inlet: 38mm (1-1/2") Model: WM3884B Depth: 102mm (4")

Base Cable s6HD - 4 Ports Base Cable Assembly for s6HD with 4 Ports. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Oberdorfer 170M-A81 Cent Pump 12V Brz 3/4 Ports FEATURES Pump Body: Bronze Ports: 3/4" NPT Flow: 12 GPM Max Pressure: 7 PSI Max, 17 feet of head Impeller: Centrifugal Shaft Seal: Buna Lip Seal Standard, Optional Viton lip Shaft: Corrosion resistant passivated 316 SS Shaft Motor / Drive: TEFC Motors 1/10 HP Permanent Magnet 12V, 24V, 32V DC Motors. Rubber base grommets for vibration dampening. Available with 1/13 HP Permanent Magnet 12V DC Motor (A95).     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED CENTRIFUGAL PUMP Ideal for: Marine Air Conditioning, Engine Block Temperature Control, Radiator and Heat Exchanger, Circulation Baitwell Circulation.     Oberdorfer Centrifugal Pump, Bronze, 12V Motor, 3/4"NPT Ports    

Oberdorfer 170M-A82 Cent Pump 24V Brz 3/4 Ports FEATURES Pump Body: Bronze Ports: 3/4" NPT Flow: 12 GPM Max Pressure: 7 PSI Max, 17 feet of head Impeller: Centrifugal Shaft Seal: Buna Lip Seal Standard, Optional Viton lip Shaft: Corrosion resistant passivated 316 SS Shaft Motor / Drive: TEFC Motors 1/10 HP Permanent Magnet 12V, 24V, 32V DC Motors. Rubber base grommets for vibration dampening. Available with 1/13 HP Permanent Magnet 12V DC Motor (A95).     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED CENTRIFUGAL PUMP Ideal for: Marine Air Conditioning, Engine Block Temperature Control, Radiator and Heat Exchanger, Circulation Baitwell Circulation.   Oberdorfer Centrifugal Pump, Bronze, 24V Motor, 3/4"NPT Ports  

Oberdorfer 170M-A87 Cent Pump 32V Brz 3/4 Ports FEATURES Pump Body: Bronze Ports: 3/4" NPT Flow: 12 GPM Max Pressure: 7 PSI Max, 17 feet of head Impeller: Centrifugal Shaft Seal: Buna Lip Seal Standard, Optional Viton lip Shaft: Corrosion resistant passivated 316 SS Shaft Motor / Drive: TEFC Motors 1/10 HP Permanent Magnet 12V, 24V, 32V DC Motors. Rubber base grommets for vibration dampening. Available with 1/13 HP Permanent Magnet 12V DC Motor (A95).     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED CENTRIFUGAL PUMP Ideal for: Marine Air Conditioning, Engine Block Temperature Control, Radiator and Heat Exchanger, Circulation Baitwell Circulation.   Oberdorfer Centrifugal Pump, Bronze, 32V Motor, 3/4"NPT Ports  

Oberdorfer 170M Cent Pump Peo Brz 3/4 Ports These Oberdorfer™ centrifugal pumps have a single open vane rotating impeller. Liquid enters at the center and is thrown outward radically by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently, a relief valve is not required.   The flow of these pumps can be conveniently controlled by a throttling valve in the discharge line. Horsepower demand will decrease as the pressure increases. Maximum horsepower occurs with a wide open discharge.   The lip seal is Nitrile with stainless steel spring reinforcement on a stainless steel motor shaft. The seal is friction press fit in a machined housing counter bore. Excessive system pressures above 15 PSI are not recommended as the seal could be forced out of the pump housing.   FEATURES Rugged Corrosion Resistant Bronze Construction Compact & Light Nitrile Lip Seal STD; Optional fluoroelastomer Lip TEFC Motors With Corrosion Resistant Passivated 316 SS Shafts 1/10 HP Permanent Magnet 12V, 24V, 32V DC Motors Rubber Base Grommets For Vibration Dampening Insulated Leads 1/13 HP Permanent Magnet 12V DC Motor (A95) Ideal for:   Marine Air Conditioning Engine Block Temperature Control Radiator & Heat Exchanger Circulation Baitwell Circulation DRIVE One of the outstanding features of this pump and motor unit is its compact D.C. motor size. Although small, adequate motor power is available.  Motors are available in 12, 24 and 32 VDC.   LIQUIDS & TEMPERATURES This pump is more than capable of pumping water, water solutions, and a wide range of commercial chemicals. Viscous liquids with a maximum viscosity of 2000 Saybolt Seconds Universal can be pumped. However, when pumping viscous liquids (as compared with water) a reduction in flow and pressure occurs and the required horsepower increases.  Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity.  Questions about the chemical compatibility of special liquids should be referred to the factory.      SUCTION LIFT These pumps are not self priming.  They must be installed below the liquid level so that the liquid flows to the pump by gravity (flooded suction).  However, if a foot valve is used at the beginning of the suction line, and all air is bled from the pump by manual priming, the pump will lift on the suction side up to 15 feet.  Such a system relies entirely on the non-leaking foot valve for starting capability.  

Jabsco 3270-0001 Engine Cooling Pump 3/4" Ports Flange Mount Perkins 4-107 Perkins 4-108 Fitting: 3/4 in. NPT Size: 4 1/4 in. long x 4 1/8 in. wide x 3 7/8 in. high Weight: 4 lb (1.8 kg) Drive: Coupling Mount: Engine    

Fill-Rite 807C Flow Meter 20Gpm 3/4" Ports The 807C Mechanical flow meter has a large easy to read display, flow ports can be positioned vertically or horizontally, UL/cUL listed, handles fluid of any viscosity, rated for Gasoline, Diesel, Kerosene, mineral spirits, Stoddard solvents and heptane. Fill-Rite meters provide precision and durability in a cost-effective design. The 807C is a 3 wheel mechanical meter designed for transfer pumps with a flow rate of 5 to 20 GPM (gallons per minute). This meter has a 3/4 " inlet and outlet.     Product features 5 to 20 gallons per minute 50 PSI (pounds per square inch) 3/4 inch inlet and outlet Large easy to read display NPT threads  

Haight Pump 8E003000-S148 Hot Oil Pump 3/4 Ports 1/2Hp Specifications Pump Body: Cast Iron Shaft Seal: Viton Mechanical Seal  

Jabsco 30510-0003 Pedestal Pump Nitrile Impeller with 3/4" Ports Pump Body: 316 Stainless Steel Pedestal Pump Port Size: 3/4" NPT Internal Flow: Nominal 8.2 US gallons/min at 1750rpm Pressure: Pressure up to 1.5 bar Impeller: Standard Pressure, Nitrile Impeller Shaft Seal: Mechanical; Carbon Shaft: 316 Stainless Steel   Easy to service and maintain. Will tolerate abrasive wear. Handles hard and soft solids without clogging. Non pulsating flow. Self-priming from dry up to 2.4m (7.8ft).   INDUSTRIAL: Circulating and transferring, velocity-mixing, pumping machine tool coolants, spill return, sump drainage, chemicals, pharmaceuticals, soap, liquors, ink, dyes, alcohol, dilute acids, tanning liquors, glycerin, brine, etc.   PHARMACEUTICAL: Processing medicines, lotions and preparations. Filtering pharmaceutical solutions. Filling line supply pump.   PAPER PROCESSING: Transferring and applying starches, sizes, etc. Circulating and processing wood pulp slurries.   FOOD, BEVERAGE & DAIRY: Transfer brines, vinegar, syrups during processing, liquids containing solids in suspension such as chopped tomatoes, nuts, etc. Removal of distillery wort and brewery slop. Processing viscous materials such as peanut butter, mayonnaise, ketchup, honey, etc. (low speed). Pumping whiskey, wine, rums, juices and ciders.   AGRICULTURAL: Transferring liquid fertilizers, herbicides and pesticides  

Jabsco 30510-0004 Pedestal Pump Standard Pressure, Viton Impeller with 3/4" Ports Pump Body: 316 Stainless Steel Port Size: 3/4" NPT Internal Flow: Nominal 8.2 US gallons/min at 1750rpm Pressure: Pressure up to 1.5 bar Impeller: Standard Pressure, Viton Impeller Shaft Seal: Mechanical; Carbon Shaft: 316 Stainless Steel Easy to service and maintain. Will tolerate abrasive wear. Handles hard and soft solids without clogging. Non pulsating flow. Self-priming from dry up to 2.4m (7.8ft). INDUSTRIAL: Circulating and transferring, velocity-mixing, pumping machine tool coolants, spill return, sump drainage, chemicals, pharmaceuticals, soap, liquors, ink, dyes, alcohol, dilute acids, tanning liquors, glycerin, brine, etc. PHARMACEUTICAL: Processing medicines, lotions and preparations. Filtering pharmaceutical solutions. Filling line supply pump. PAPER PROCESSING: Transferring and applying starches, sizes, etc. Circulating and processing wood pulp slurries. FOOD, BEVERAGE & DAIRY: Transfer brines, vinegar, syrups during processing, liquids containing solids in suspension such as chopped tomatoes, nuts, etc. Removal of distillery wort and brewery slop. Processing viscous materials such as peanut butter, mayonnaise, ketchup, honey, etc. (low speed). Pumping whiskey, wine, rums, juices and ciders. AGRICULTURAL: Transferring liquid fertilizers, herbicides and pesticides   Jabsco Pedestal Pump 316SS 3/4" NPT Std Pressure Nitrile Impeller Carbon Seal

Jabsco 30642-1000 90 Degree 3/4" Port  

Fill-Rite F3135 12' Hose 3/4" Buna W/Static