|
Stainless Steel Temperature Probe w/RJ Connector
Measure temperature of air, soil, or water with this multi-purpose temperature probe.
Add up to four probes to a single Leaf & Soil Moisture/Temperature Station. Or add to Vantage Connect and use in place of Vantage Connect's internal temperature sensor. Great option for measuring water or soil temperature without adding another station.
Probe has a 2-1/2" (64mm)-long stainless steel housing and includes 15' (4.6M) direct-burial cable.
Compatible with Wireless Temperature Station (6372), Weather Envoy (6316), Envoy8X (6318), and Anemometer/Sensor Transmitter Kit (6332).
|
81.82 |
|
|
Stainless Steel Temperature Probe w/Two-Wire Termination
Measure temperature of air, soil, or water with this multi-purpose temperature probe.
Add up to four probes to a single Leaf & Soil Moisture/Temperature Station. Or add to Vantage Connect and use in place of Vantage Connect's internal temperature sensor. Great option for measuring water or soil temperature without adding another station.
Probe has a 2-1/2" (64mm)-long stainless steel housing and includes 15' (4.6M) direct-burial cable.
Compatible with both original Vantage Pro and Vantage Pro2.
|
92.04 |
|
|
Temperature Probe with RJ Connector
Used to measure air, soil, or water temperature. Features an electronic sensor sheathed in black UV-stabilized plastic. Includes 25' (7.6M) cable.
Compatible with Weather Envoy, Envoy8X, and Anemometor/Sensor Transmitter Kit.
|
46.02 |
|
|
Stainless Steel Table Base w/Locking Pin
Stainless Steel Table Support with Locking Pull Pin
Tube Size: 1-5/8''
Flange Dia.: 6-1/4"
|
102.04 |
|
|
Stainless Steel Pad Eyes w/Stainless Steel Screws
The Tigress line of outrigging accessories features a great selection of accessories to fit the needs of any fisherman.
Whether you have 15' skiff poles or 35' double rigged tournament poles, Tigress has a rigging accessory for you. All accessories feature top quality materials and are ready to be installed.
|
6.52 |
|
|
Temperature Probe for SST-110 Transom Mount
Stainless Steel Temp Probe for Sitex SST-110
Also works with Dytek Temp guages.
|
63.00 |
|
|
Airmar T80 Water Temperature Probe (8-pin)
Find out the water surface temperature by attaching our 8-pin stainless steel temperature probe to your transducer.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
142.80 |
|
|
50 AMP Male Stainless Steel Combo Kit
The SmartPlug 50 AMP Combo kit includes the 50 AMP Stainless Steel inlet (BM50S) and 50AMP connector (BF50), everything you need to protect your boat from shore power overheating.
Installation of both components is easy. The kit is designed to fit on 125/250 V systems with multiple seals on the connector to ensure a watertight fit on an existing cordset.
Features
Reduces Overheating – Increased pin and clip surface area greatly improves electrical conductivity during high amperage demand.
Ease of Use – No twist required, the unique plug body shape and push-in design means it only goes in the right way every time-even in the dark.
Multi-Point Locking System – Side clips lock the plug securely into the inlet which eliminates any stress on the pins from movement of the power cord.
Weatherproof Seals – Superior gaskets installed in the inlet cover and interior of the plug body eliminates moisture penetration.
Quick and Easy Installation – Inlet mounting flange holes match twist-type holes for an installation that is typically finished in 30 minutes.
*Sold as an Individual
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
290.12 |
|
|
XKA Stainless Steel Trim Tab with ALC-1 Control - 12 x 24
The Lectrotab stainless steel trim tab design provides unmatched strength and reliability. All stainless steel tabs are fabricated with a continuous rolled and pinned hinge. This design eliminates the need for welding.
Combined with a precision-engineered actuator, this kit is built to combine quiet operation with a non-hydraulic, maintenance free design. The unit is corrosion free, ensures very accurate tab positioning, provides maximum lift force, and is totally self-contained for easy installation. The actuator assembly is packaged in a non-metallic permanently sealed housing. No components need to be installed inside the boat.
Most importantly, unlike hydraulic trim tabs, there is no oil to leak out. The actuator incorporates either a standard or low profile transom mounting bracket.
The Automatic Leveling Control (ALC) will automatically adjust your trim tabs to maintain a level boat for a more comfortable and enjoyable ride. Additionally, the ALC automatically corrects the roll from side to side and pitch from fore to aft to enhance your boating experience and improve your fuel economy.
Features:
Continuous rolled and pinned hinge provides added strength and eliminates the need for welding
Upper ram seal location cannot be damaged due to fouled ram or barnacle growth
Utilizes internal pressure equalization system
Internal brake system prevents unwanted tab movement when under way or backing down
Quiet operation
Actuators are fully load tested to push 1000 lbs of force
Non-metallic external structure which cannot corrode and will not deteriorate in the sun or under water
Technical Specifications:
Trim Tab Size (L x W) - 12" x 24" (30 x 61 cm)
Boat Length - 28' to 48' (8.5 to 14.5 M)
Trim Tab Material - 12 gauge, 304 Stainless Steel
Actuator DC Voltage - 12 V
Actuator Stroke Length - 2.25" (57 mm)
Actuator Cable Length - 23' (7 M)
Actuator Vertical Height - 11.875" (302 mm)
Control Dimensions (W x H) - 3.15" x 3.07" (80 x 77 mm)
Control Mounting Hole Cutout - 2" (50 mm)
Control Operating Voltage - 12 or 24 V
In the Box:
One (1) Automatic Leveling Control
Two (2) Stainless Steel tabs
Two (2) actuators w/23' (7 M) cables
Instruction Manual
*Sold as a Kit
|
2402.17 |
|
|
V46 - 13.5" Stainless Steel Steering Wheel with Speed Knob - Black
Features:
Speed knob included
All black, including the speed knob
Steering wheels are CE marked in conformity with the EN 28848 – EN 29775 and ABYC P22 safety standards
Specifications:
Diameter: (inch) 13.5"
Material: Stainless steel
3 spokes
*Note: Wheel nut is not included and is needed for installation
|
276.43 |
|
|
V46 - 13.5" Stainless Steel Steering Wheel with Speed Knob
Features:
Polished stainless steel
Speed knob included
Steering wheels are CE marked in conformity with the EN 28848 – EN 29775 and ABYC P22 safety standards
Specifications:
Diameter: (inch) 13.5"
3 spokes
*Note: Wheel nut is not included and is needed for installation
|
164.78 |
|
|
Swivel Base Rod Holders
RH570
Stainless Steel Side Mount w/ Swivel Base
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a inch stainless steel lock nut at the bottom of the rod holder.
|
210.00 |
|
|
Swivel Base Rod Holders
RH570XL
Stainless Steel Side Mount w/ Swivel Base Extra Long
This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
230.77 |
|
|
Swivel Base Rod Holders
RH575
Standard Angle 30°
Stainless Steel Flush Mount w/ Swivel Base
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
162.70 |
|
|
Swivel Base Rod Holders
RH575XL
Standard Angle 30°
Stainless Steel Flush Mount w/ Swivel Base Extra Long
This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface.
Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin.
Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.
|
162.07 |
|