|
5" x 12" x 1" Self Drain™ Opening Port
The Beckson Self Drain™ Opening Port is innovatively designed with an angled drainage ramp molded on the inside of the spigot. This design promotes drainage without having the hassle of making angled cuts in the hull. This also allows for thru-bolting, which is impossible in windows where an angled spigot extends below the bolt holes. The internal angle seats tightly against the gasket and lens, thus omitting an exterior water retention ledge present in most other ports. (No water-fall when you open the port after a rain.) Self Drain™ Opening Ports are ideal for mounting where installation is within 15x of vertical (with spigot length up to one inch). Longer spigots are available for vertical installations. For greater angles use Beckson Rain Drain™ Ports.
|
193.73 |
|
|
5" x 12" x 2" Self Drain™ Opening Port
The Beckson Self Drain™ Opening Port is innovatively designed with an angled drainage ramp molded on the inside of the spigot. This design promotes drainage without having the hassle of making angled cuts in the hull. This also allows for thru-bolting, which is impossible in windows where an angled spigot extends below the bolt holes. The internal angle seats tightly against the gasket and lens, thus omitting an exterior water retention ledge present in most other ports. (No water-fall when you open the port after a rain.) Self Drain™ Opening Ports are ideal for mounting where installation is within 15° of vertical (with spigot length up to one inch). Longer spigots are available for vertical installations. For greater angles use Beckson Rain Drain™ Ports.
|
193.73 |
|
|
Replacement Portlight Lens Only - 5" x 12" - Smoke
Replacement lens only for Beckson Opening Ports
Features:
5" x 12"
Smoke
|
61.33 |
|
|
Smart Tabs SX Series 10.5 X 12 f/21-25' Boats w/150-220 HP
IMPROVES YOUR BOAT'S OVERALL PERFORMANCE - GUARANTEED!!!
If these trim tabs don't provide you with an outstanding performance increase, contact us within 30 days of your purchase.
Why buy a manually adjusting trim tab set when you can get the automatic trim tabs that will self adjust and performance better for less money?
The SX series incorporates all of the fully automatic features of our popular SMART TABS, in addition to the rust and corrosion free benefits of molded composite materials. Assembly can be completed in seconds and the installation in a few minutes. The only tools required are a drill with a 3/16" bit and a phillips screw driver. SMART TABS SX provide un-equaled performance and durability with no maintenance in fresh or salt water. The system can be specifically tuned to maximize the performance of any power boat, and TRACKING RIBS have been added to improve handling at higher speeds.
Our breakthrough technology in trim tabs is completely automatic requiring no operator adjustment while underway. Nauticus trim tabs self adjust according to how you load and maneuver your boat.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.
Reduce the minimum planning speed by up to 33%
Faster Acceleration
Increase top speed
Provide a level, more comfortable ride at lower speeds
Improve fuel economy, handling and safety
NO HYDRAULICS - NO ELECTRIC SWITCHES
Nauticus trim tabs are completely automatic requiring no operator adjustment while underway.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation. (see installation instruction).
SPEED REGULATION
Nauticus trim tabs start in a downward angel to maximize lift at slow speeds. As the boat accelerates, the water pushes up on the trim plates providing lift to the stern which minimizes bow rise, and allows the boat to plane quickly.
Once the water pressure exceeds the actuator load rating (maximum lift) the trim plates move up to a horizontal position eliminating any drag.
BOAT STABILIZERS
Even when cruising SMART TABS continue to work like shock absorbers. The constant adjustment to sea conditions allow SMART TABS to provide remarkable stability in turns, while crossing waves, while cruising, and while running at maximum speeds. No more sliding, porpoising, or chine walking.
ONE OF A KIND
The unique system is the only one of its kind in the industry. The internal valve system is truly "smart" in its design of controlling you boats performance.
It will reduce the minimum planning speed by 33% Provide a level, more comfortable ride at lower speeds Improve economy, handling and safety
As the boat speed increases, the water pressure also increases. Once the water pressure exceeds the Actuator load rating (maximum LIFT period) the trim plates begin to move upward until they are horizontal with the bottom of the boat.
The internal valve system dampens the trim plate movement which eliminates any instant reaction to minor water pressure variances. Nauticus trim tabs provide smooth and undetectable reaction to boat speed creating a level, more comfortable ride at lower speeds.
INSTALLATION IS SIMPLE
With an electric drill, small drill bit, a phillips screwdriver, and two wrenches, just about anyone can install SMART TABS in less than an hour. Professional installers should be able to install SMART TABS in 30 minutes or less.
All mounting hardware, instructions, and templates are included.
SMART TABS require NO THROUGH HULL DRILLING
|
143.22 |
|
|
Smart Tabs SX Series 10.5 X 12 f/21-25' Boats - Up To 350 HP
IMPROVES YOUR BOAT'S OVERALL PERFORMANCE - GUARANTEED!!!
If these trim tabs don't provide you with an outstanding performance increase, contact us within 30 days of your purchase.
Why buy a manually adjusting trim tab set when you can get the automatic trim tabs that will self adjust and performance better for less money?
The SX series incorporates all of the fully automatic features of our popular SMART TABS, in addition to the rust and corrosion free benefits of molded composite materials. Assembly can be completed in seconds and the installation in a few minutes. The only tools required are a drill with a 3/16" bit and a phillips screw driver. SMART TABS SX provide un-equaled performance and durability with no maintenance in fresh or salt water. The system can be specifically tuned to maximize the performance of any power boat, and TRACKING RIBS have been added to improve handling at higher speeds.
Our breakthrough technology in trim tabs is completely automatic requiring no operator adjustment while underway. Nauticus trim tabs self adjust according to how you load and maneuver your boat.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.
Reduce the minimum planning speed by up to 33%
Faster Acceleration
Increase top speed
Provide a level, more comfortable ride at lower speeds
Improve fuel economy, handling and safety
NO HYDRAULICS - NO ELECTRIC SWITCHES
Nauticus trim tabs are completely automatic requiring no operator adjustment while underway.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation. (see installation instruction).
SPEED REGULATION
Nauticus trim tabs start in a downward angel to maximize lift at slow speeds. As the boat accelerates, the water pushes up on the trim plates providing lift to the stern which minimizes bow rise, and allows the boat to plane quickly.
Once the water pressure exceeds the actuator load rating (maximum lift) the trim plates move up to a horizontal position eliminating any drag.
BOAT STABILIZERS
Even when cruising SMART TABS continue to work like shock absorbers. The constant adjustment to sea conditions allow SMART TABS to provide remarkable stability in turns, while crossing waves, while cruising, and while running at maximum speeds. No more sliding, porpoising, or chine walking.
ONE OF A KIND
The unique system is the only one of its kind in the industry. The internal valve system is truly "smart" in its design of controlling you boats performance.
It will reduce the minimum planning speed by 33% Provide a level, more comfortable ride at lower speeds Improve economy, handling and safety
As the boat speed increases, the water pressure also increases. Once the water pressure exceeds the Actuator load rating (maximum LIFT period) the trim plates begin to move upward until they are horizontal with the bottom of the boat.
The internal valve system dampens the trim plate movement which eliminates any instant reaction to minor water pressure variances. Nauticus trim tabs provide smooth and undetectable reaction to boat speed creating a level, more comfortable ride at lower speeds.
INSTALLATION IS SIMPLE
With an electric drill, small drill bit, a phillips screwdriver, and two wrenches, just about anyone can install SMART TABS in less than an hour. Professional installers should be able to install SMART TABS in 30 minutes or less.
All mounting hardware, instructions, and templates are included.
SMART TABS require NO THROUGH HULL DRILLING
|
143.22 |
|
|
Groco S-84 Tie Rod, Monel .5 X 12.125
|
188.44 |
|
|
MA-4052LG1 5" 60 Watt LED Self Draining Spa Speaker - Dark Grey
State of the art music for your spa system. Superior sound, LED lighting and all with elegant styling and rugged construction combined to provide years of enjoyable trouble-free service. All materials used are thoughtfully selected to resist spa chemicals, withstand UV exposure and block corrosion.
Self-draining to prevent water from collecting inside the cone of the speaker.
Features:
Audio-signal-synched LED performance
Socket head capped screws included
Self-draining speaker cone for water drainage
Specifications:
Speaker Impedance - 4 ohms
5.3 oz Driver magnet
1-1/4" Tweeter
Peak Power - 60 watts
Outside Diameter - 5.83" (148 mm)
Cutout Diameter - 4.33" (110mm)
Mounting Depth - 2.77" (70.25 mm)
Weight - 1.15 lbs per speaker
*Sold as an Individual
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
39.46 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Black
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes and reinforced ropeholds for long-term durability.
Utility boat fenders with Polyform dependability.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Twin-eye design for vertical or horizontal use
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5cm)
Eye Diameter - .375" (1cm)
Circumference - 11" (27.9cm)
Volume - .4 gallons (1.5L)
Boat Size - Up to 10' (up to 3M)
Weight - .8lbs
*Sold as an Individual
|
16.15 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Blue
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes and reinforced ropeholds for long-term durability.
Utility boat fenders with Polyform dependability.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Twin-eye design for vertical or horizontal use
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5cm)
Eye Diameter - .375" (1cm)
Circumference - 11" (27.9cm)
Volume - .4 gallons (1.5L)
Boat Size - Up to 10' (up to 3M)
Weight - .8lbs
*Sold as an Individual
|
10.79 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - White
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes and reinforced ropeholds for long-term durability.
Utility boat fenders with Polyform dependability.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Twin-eye design for vertical or horizontal use
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5cm)
Eye Diameter - .375" (1cm)
Circumference - 11" (27.9cm)
Volume - .4 gallons (1.5L)
Boat Size - Up to 10' (up to 3M)
Weight - .8lbs
*Sold as an Individual
|
11.99 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Cobalt Blue
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes and reinforced ropeholds for long-term durability.
Utility boat fenders with Polyform dependability.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Twin-eye design for vertical or horizontal use
Unique Polyform valve for years of service
One (1) piece design
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5cm)
Eye Diameter - .375" (1cm)
Circumference - 11" (27.9cm)
Volume - .4 gallons (1.5L)
Boat Size - Up to 10' (up to 3M)
Weight - .8lbs
*Sold as an Individual
|
10.79 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Graphite
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced rope holds for long-term durability.
The G Series fender is designed to provide protection and stand-off for vessels between 10 to 40 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Hangs vertically or horizontally
Unique Polyform valve for years of service
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5 cm)
Eye Diameter - 0.375" (1 cm)
Circumference - 11" (27.9 cm)
Volume - 0.4 gallons (1.5 L)
Boat Size - Up to 10' (3 M)
Weight - .7 lb
*Sold as an Individual
|
9.59 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Sand with Adapter
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced rope holds for long-term durability.
The G Series fender is designed to provide protection and stand-off for vessels between 10 to 40 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Hangs vertically or horizontally
Unique Polyform valve for years of service
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5 cm)
Eye Diameter - 0.375" (1 cm)
Circumference - 11" (27.9 cm)
Volume - 0.4 gallons (1.5 L)
Boat Size - Up to 10' (3 M)
Weight - .7 lb
In the Box:
Fender
Inflation Adapter
*Sold as a Kit
|
11.99 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Sand
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced rope holds for long-term durability.
The G Series fender is designed to provide protection and stand-off for vessels between 10 to 40 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Hangs vertically or horizontally
Unique Polyform valve for years of service
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5 cm)
Eye Diameter - 0.375" (1 cm)
Circumference - 11" (27.9 cm)
Volume - 0.4 gallons (1.5 L)
Boat Size - Up to 10' (3 M)
Weight - .7 lb
*Sold as an Individual
|
10.79 |
|
|
G-1 Twin Eye Fender 3.5" x 12.8" - Pink
Polyform’s G Series boat fender has raised the bar for quality and appearance in utility fenders. Subscribing to the philosophy that quality does not have to cost more, we include ribs for extra strength, inflation valves for larger sizes, and reinforced rope holds for long-term durability.
The G Series fender is designed to provide protection and stand-off for vessels between 10 to 40 feet in length.
Features:
Even wall thickness for maximum strength and durability
Molded-in ribs for strength and abrasion resistance
Reinforced ropeholds
Designed for use by trailered boats and in permanent protected moorings
Hangs vertically or horizontally
Unique Polyform valve for years of service
Technical Specifications:
Size (diameter x length) - 3.5" x 12.8" (8.9 x 32.5 cm)
Eye Diameter - 0.375" (1 cm)
Circumference - 11" (27.9 cm)
Volume - 0.4 gallons (1.5 L)
Boat Size - Up to 10' (3 M)
Weight - .7 lb
*Sold as an Individual
|
16.15 |
|