Standard Pin Rail 3-9/16"H x 7/8"D x 5'L 5' length

L-Type Pin Rail 2-9/16"H x 7/8"D x 5'L 5' length

Corner Wire Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Cap Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

"L" Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

"L" Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Stop Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Stop Molding Use for a beautiful smooth finish to your project. Constructed with 100% Solid Teak. Length: 5'

Teak LED Dome Light - 5" Lens  These LED Dome Lights feature a solid teak base with a lacquer coated brass trim ring. Prewired with integral on/off toggle switch. Low current consumption of 0.068 amps @ 12 volts, they give off very little heat and have extremely long service life. These vibration resistant LED Dome Lights feature 18 white LEDs per light. Surface mounts with #8 FH fasteners (not included). WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Standard Dee Slotted Pin Shackle - 5/32" Pin - 5/8"L x 3/8"W Features: Slotted shackle pins are low profile to prevent snagging on ropes etc... Grade 316 Stainless Steel bodies and pins

Standard Dee Slotted Pin Shackle - 5/32" Pin - 1/2"L x 5/16"W Features: Slotted shackle pins are low profile to prevent snagging on ropes etc... Grade 316 Stainless Steel bodies and pins

KingPin™ Power-Rise Stand-Up Standard Pin - 23-1/2" to 30-1/2" - 1-Pack Features: Adjustable Height To Be Used As A Seat Or Leaning Post Rotates 360°, Adjusts From 22-1/2″ To 29-1/2″ Use With Standard KingPin™ Base (sold separately) Rated ABYC Class H-31 B (Fishing Only) 

KingPin™ Power-Rise Sit-Down Standard Pin - 1-Pack Features: Adjustable Height To Be Used As A Seat Or Leaning Post Rotates 360°, Adjusts From 22-1/2″ To 29-1/2″ Use With Standard KingPin™ Base (sold separately)  Rated ABYC Class H-31 B (Fishing Only)

KingPin™ Power-Rise Stand-Up Package Standard Pin Features: Standard Power-Rise Stand-Up Post (1611431-S) Quik-Tilt Seat Mount (1615254-EC) Gray, Pro Stand-Up Seat (1040213) Adjusts From 23-1/2″ To 30-1/2″ Use With Standard KingPin™ Base (sold separately) Rated ABYC Class H-31 B (Fishing Only) 

GP1040-22 SystemPod Pre-Cut for Raymarine ES97/ES98 & Space On The Left for 9.5 Wide Guard NavPod GP1040 Series for 9.5" Guard SystemPods are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic. A SystemPod is best mounted on a Single Bend AngleGuards. The Hi-Gloss Material NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity. The Waterproof Seal All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The Nickel Chrome Plated Screws We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling! The Manufacturing Process Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances. Our Commitment to Quality We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.