VE. Can to NMEA 2000 Micro-C Male Cable Use this cable to connect a Victron product with a VE. Can port to a NMEA2000 network. Warranty Info WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. Please contact your dealer for any returns, repairs or support issues related to this product.

Lynx Smart BMS 1000 Battery Management System for Lithium Smart Batteries The Lynx Smart BMS is a dedicated Battery Management System (BMS) for the Victron Lithium Battery Smart batteries. These batteries are Lithium Iron Phosphate (LiFePO4) batteries and are available in 12.8 V or 25.6 V in various capacities. They can be connected in series, parallel, and series/parallel so that a battery bank can be built for system voltages of 12V, 24 V, or 48 V. The maximum number of batteries in one system is 20, which results in a maximum energy storage of 84 kWh in a 12 V and up to 102 kWh in a 24 V1) and 48 V1) system. Out of the various available BMSes, the Lynx Smart BMS is the most feature-rich and complete option and integrates seamlessly into the Lynx Distributor system. This model is a 1000 A (M10) version. Built-in 1000 A Contactor The contactor acts as a secondary safety system to protect the battery in case the primary controls (ATC, ATD, and/or DVCC) fail to disable loads and/or chargers when required and is also suitable as a remote controllable main system switch. Pre-charge Circuit In addition to the contactor, a built-in pre-charge circuit prevents high inrush currents when connecting a capacitive load such as a MultiPlus/Quattro or other inverter, eliminating the need for external pre-charging. Monitoring and Control Monitor and control the BMS via Bluetooth using the VictronConnect App or a GX device such as a Cerbo GX and the VRM Portal. A built-in battery monitor that operates similarly as the other Victron Energy battery monitors, provides data such as state of charge, voltage, current, historical data, status info, and more in real-time and with instant readout even without the need to connect to the BMS, allowing diagnostic at a glance. DVCC closed Loop Control as Well as ATC/ATD Contacts Compatible Victron inverters/chargers and solar chargers are automatically controlled via a connected GX device and DVCC. The ATC/ATD contacts can be used to control other chargers and loads that have a remote on/off port. Programmable Relay The relay can be used either as an alarm relay (combined with the pre-alarm) or to control an alternator via its external regulator (ignition cable). In Alternator ATC mode, the relay will only activate when the contactor is closed. Alternator ATC contact of the alternator opens first and then with a delay of 2 seconds the contactor. These 2 seconds ensure that the alternator is switched off before the battery is disconnected from the system. AUX Terminal The advantage of the onboard auxiliary power supply (1.1 A @ system voltage) is to provide power to specific loads (i.e. a GX device) after the BMS has shut down the loads in the event of a low cell voltage event. If no charge voltage is detected within 5 minutes, the BMS, including the AUX connection switches off. VE.Can and NMEA 2000 Data Communication VE.Can allows for easy connection (standard RJ45 network cable) and communication with a GX device. Since the CANbus protocol is based on NMEA 2000 (and J1939), it is easy to integrate into a marine network and feed a marine MFD with data (requires a VE.Can to NMEA 2000 micro-C male cable). Lynx Distributor Fuse Monitoring Read out the fuse status and receive an alarm in case a fuse is blown. The Lynx Smart BMS monitors up to 4 connected Lynx Distributors and their fuses via VictronConnect or a GX device 1) To reduce the required balancing time, we recommend using as many different batteries in series as possible for the application. 24 V systems are best built using 24 V batteries, and a 48 V system. This System Contains the Following Components: Lynx Distributor with 2 fused paralleled lithium-ion smart batteries. Lynx Smart BMS with BMS, contactor, and battery monitor A second Lynx distributor provides fused connections for inverter/charger(s), loads and chargers (additional modules can be added if more connections are needed) A Cerbo GX (or other GX device) to read out the Lynx Smart BMS and Lynx Distributor data. Power Specifications: Battery Voltage Range: 9 – 60 VDC Maximum Input Voltage: 75 VDC Supported System Voltages: 12, 24, or 48 V Reverse Polarity Protection: No Main Safety Contactor Continuous Current Rating: 1000 A continuous Main Safety Contactor Peak Current Rating: 1200 A for 5 minutes  Power Consumption OFF Mode: 0.3 mA for all system voltages Power Consumption in Standby Mode: Approximately 0.6 W (50 mA at 12 V) Power Consumption in ON Mode: Approx. 2.6 W (217 mA at 12 V) depending on the state of the relays Approximately 4.2 W (350 mA at 12 V) depending on the state of the relays Minimum Load Resistance for Pre-Charging: 10 Ω and above for 12 V systems, 20 Ω and above for 24 V and 48 V systems AUX Output Maximum Current Rating: 1.1 A continuous, protected by resettable fuse Allow-to-Charge Port Maximum Current Rating: 0.5 A at 60 VDC, protected by a resettable fuse Allow-to-Discharge Port Maximum Current Rating: 0.5 A at 60VDC, protected by a resettable fuse Alarm Relay (SPDT) Maximum current Rating: 2 A at 60 VDC Connections: Busbar: M10 (Torque: 17 Nm) VE.Can: RJ45 I/O: Removable multi-connector with screw terminals Battery BTV Cables: Male and female circular 3-pole connector with M8 screw ring Up to 20 batteries can be connected in one system Lynx Distributor fuse monitoring (up to 4 modules) RJ10 (cable ships with each Lynx Distributor) Physical Specifications: Enclosure Material: ABS Enclosure Dimensions (h x w x d): 230 x 180 x 100 mm Unit Weight: 2.7 kg Busbar Material: Tinned copper Busbar Dimensions (h x w): 8 x 30 mm Environmental Specifications: Operating Temperature Range: -40 °C to +60 °C Storage Temperature Range: -40 °C to +60 °C Humidity Max.: 95 % (non-condensing) Protection Class: IP22 Standards Safety: EN-IEC 63000:2018 EMC: EN-IEC 61000-6-3:2007/A1:2011/AC:2012 QMS: NEN-EN-ISO 9001:2015 Please contact your dealer for any returns, repairs or support issues related to this product.

NMEA 2000 Micro Terminator - Male  Furuno's NMEA2000 Micro Terminator with male connector. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Micro Terminator - Female  Furuno's NMEA 2000 Micro Terminator with female connector. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 - 2M Cable NMEA 2000 Micro-C Medium duty cable. 2M (6.5 ft) Low loss 18 gauge cable recommended for network backbone runs.

N2KEXT Cable Micro-C - 10M Medium Duty Cable - N2K NMEA 2000 Micro-C Medium duty cable. 10M (33 ft) Low loss 18 gauge cable recommended for network backbone runs.

NMEA 2000 T-Connector - Male This NMEA 2000 T-connector offers connection between NMEA 2000 drop cables and backbone cables. The couplers connect to the corresponding T-connectors and backbone cables, creating a simplified installation.  Features: Includes (1) NMEA 2000 T-connector 1-Year Limited Warranty

Simrad SimNet Product to NMEA 2000 Network Adapter Cable The Simrad SimNet Product to NMEA 2000® Network Adapter Cable, manufactured by Simrad, is used to connect a Simrad SimNet product like the NMEA 2000®/NMEA 0183 Adapter (AT10) or CX NavStation Series products to an NMEA 2000® network as shown in the following diagram. The cable is 0.5 meters in length and has a female SimNet connector on one end and a standard male NMEA 2000® Micro Series connector on the other end.

Devicenet Male ADP Cable SeaTalkng to NMEA 2000 Adapts SeaTalkng to NMEA2000 network. For use with E & C Series Widescreen, G Series, and ST70 systems. Male: 1.5M cable

SimNet to Micro-C Mast Cable - 35M 35M (115') NMEA 2000 Wind Vane Cable (Micro-C Male - Simnet).

NMEA 2000 Liquid Level Sensor - 200 to 600mm The NMEA 2000® Liquid Level Sensor overcomes a laundry list of issues that plague traditional fluid level monitoring solutions, including being certified for drinking water—an industry first.   Powered by an NMEA 2000 network, three models are available to accommodate a wide range of tank depths from 200 mm to 1500 mm. The capacitive sensor is easily selectable between fresh and waste water, and is micro-adjustable for tank size. Unlike reed technology that only reports tank level in graduated steps, the Veratron NMEA 2000 Liquid Level Sensor, thanks to capacity measuring technology, offers level linearity on the full range. This provides precise data to make informed decisions on refilling and pumping out or discharging, for up to 4 tanks. Completely plug-and-play, the Veratron sensor simply connects directly into the NMEA backbone with its integrated Micro-C M12 5-pin NMEA 2000 connector. This provides the nominal 12V power and the ability to view tank level from any networked display. UL94, CE, REACH and RoHS compliant, the NMEA 2000 Liquid Level Sensor is IPX9K rated as an exposed device.  Features: Includes Flange Installation Kit 300mm NMEA Pigtail Connection Technical Specifications: Connector - NMEA 2000 Micro-C 5 pin M12 Male IP Protection Class - IPX9K In the Box: Sensor Sealing Kit Rubber Gasket Mounting Bracket Mounting Screws and Allen Wrench  *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Liquid Level Sensor - 600 to 1200mm The NMEA 2000® Liquid Level Sensor overcomes a laundry list of issues that plague traditional fluid level monitoring solutions, including being certified for drinking water—an industry first.   Powered by an NMEA 2000 network, three models are available to accommodate a wide range of tank depths from 200 mm to 1500 mm. The capacitive sensor is easily selectable between fresh and waste water, and is micro-adjustable for tank size. Unlike reed technology that only reports tank level in graduated steps, the Veratron NMEA 2000 Liquid Level Sensor, thanks to capacity measuring technology, offers level linearity on the full range. This provides precise data to make informed decisions on refilling and pumping out or discharging, for up to 4 tanks. Completely plug-and-play, the Veratron sensor simply connects directly into the backbone with its integrated Micro-C M12 5-pin NMEA 2000 connector. This provides the nominal 12V power and the ability to view tank level from any networked display. UL94, CE, REACH and RoHS compliant, the NMEA 2000 Liquid Level Sensor is IPX9K rated as an exposed device.  Features: Includes Flange Installation Kit 300mm NMEA Pigtail Connection Technical Specifications: Connector - NMEA 2000 Micro-C 5 pin M12 Male IP Protection Class - IPX9K In the Box: Sensor Sealing Kit Rubber Gasket Mounting Bracket Mounting Screws and Allen Wrench  *Sold as an Individual  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Liquid Level Sensor - 1200 to 1500mm The NMEA 2000® Liquid Level Sensor overcomes a laundry list of issues that plague traditional fluid level monitoring solutions, including being certified for drinking water—an industry first.   Powered by an NMEA 2000 network, three models are available to accommodate a wide range of tank depths from 200 mm to 1500 mm. The capacitive sensor is easily selectable between fresh and waste water, and is micro-adjustable for tank size. Unlike reed technology that only reports tank level in graduated steps, the Veratron NMEA 2000 Liquid Level Sensor, thanks to capacity measuring technology, offers level linearity on the full range. This provides precise data to make informed decisions on refilling and pumping out or discharging, for up to 4 tanks. Completely plug-and-play, the Veratron sensor simply connects directly into the backbone with its integrated Micro-C M12 5-pin NMEA 2000 connector. This provides the nominal 12V power and the ability to view tank level from any networked display. UL94, CE, REACH and RoHS compliant, the NMEA 2000 Liquid Level Sensor is IPX9K rated as an exposed device.  Features: Includes Flange Installation Kit 300mm NMEA Pigtail Connection Technical Specifications: Connector - NMEA 2000 Micro-C 5 pin M12 Male IP Protection Class - IPX9K In the Box: Sensor Sealing Kit Rubber Gasket Mounting Bracket Mounting Screws and Allen Wrench  *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

NMEA 2000 Inline Terminator - Female Features: Color - White Connector - Inline NMEA 2000 Connection - 1 Female *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

LinkUp Analog to NMEA 2000 Gateway The resistive-type LinkUp gateway provides an easy method to convert vessel and engine information to NMEA 2000. Easily installed, the LinkUp Gateway replaces the original wiring, delivering power to both the LinkUp device and sensor from the NMEA 2000 backbone while still being complaint with the NMEA 2000 certification requirements.  Configuring the LinkUp Gateway is simple using a mobile device and the companion LinkUp Configuration App for Android or IOS. Each device has a built-in passive NFC antenna, so the parameters of the sensors are wirelessly configured to type, instance and warning threshold on the mobile device which is then "tapped" against the LinkUp device for instant data download.  Features: User-friendly configuration through wireless interface and companion smartphone App Sensor Cable length - 25cm NMEA 2000 Cable length - 25 cm Tap to download parameters Mobile App for Android or IOS No power required to program No certification required Bi-directional communication, programming interface or data recovery Supported Sensors: Fuel Level Oil/Boost Pressure Fresh/Waste Water Level Oil/Gear Oil/Coolant Temperature Trim Tabs Rudder Angle Technical Specifications: Standard M12 NMEA 2000 plug LED Notification  Operating Voltage - 6 - 16.5V Nominal Voltage - 12 V (from NMEA 2000 network) IPX7 Rated Sensor Plug - Superseal Female 2 Pin Counterpart Sensor Plug - - Superseal Male 2 Pin *Sold as an Individual  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.