Tuthill 1LEV-C-A-88520-7 Pump W/3Ph 1/2Hp Motor

Tuthill 1LEV-C-A-88513-7 Pump And Motor

Tuthill 1LEV-C-A-88494-7 Pump And Motor

Tuthill 1LEV-C-A-88462 Pump 3.2Gpm 1/2Hp 1725Rpm 1P

Tuthill 1LEV-C-A-7 Pump 3.2Gpm Tang Shaft Cast Iron Rotary Gear Pump Pump End Only L Series Pump Cast Iron Construction NO motor Has Internal Relief Valve. Relief valve is set at 55 PSI (can be adjusted in field) Clockwise rotation only (from shaft end view) Tang Shaft Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 3.0 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU

Tuthill 1LEV-C-7 Pump 3.2 Gpm Cast Iron Rotary Gear Pump Pump End Only Tuthill L Series Pump Cast Iron Construction Has Internal Relief Valve Relief valve is set at 55 PSI (can be adjusted in field). Clockwise rotation only (from shaft end view) Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 3.0 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU

Groco C-60 12V Deck Wash Pump, 12Volt  Groco- Deck Wash Vane Pump System 6.5GPM 20-40psi 12VDC   More Info: C60

Groco C-60 24V Deck Wash Pump, 24Volt  Groco- Deck Wash Vane Pump System 6.5GPM 20-40psi 24VDC   More Info: C60

Tuthill 2LEV-C-A-7 Pump 6.2Gpm Short Shaft Type: Internal Gear Maximum Flow Rate: 6.2 gpm Max Pressure: 300 psi Inlet/Outlet Port Sizes: 1/2 in NPT Pump Body Material: Cast Iron Wetted Materials: Steel, Carbon, Bronze, P/M Steel, Carbon O-Ring Material: Viton, Neoprene, EPR Seal: Viton Mechanical Seal

Tuthill 0LEV-C-A-7 Pump Tuthill 0LEV-C-A-7 Pump with Relief valve CW rotation only with Tang Shaft Tuthill 0LE Series are compact, highly efficient, cast iron positive displacement rotary gear pumps with a mechanical seal. Pumping action is based on a rotor, idler gear, and a cover cast with a crescent-shaped partition. They are self priming and particularly suited to handle liquids of 35 to 1000 SSU viscosity. Higher viscosities can be handled at reduced speeds. The pump has a non-pulsating flow and runs substantially quieter than other pump designs.   Features : Pump Body: Cast Iron Relief Valve: Relief valve is factory set to 55 PSI for spring adjustment between 55-120 PSI. Shaft Seal: Mechanical Seal Viton Port Size: Inlet Port is 1/2 inch NPT, Discharge Port is 1/2 inch NPT.

Tuthill 4C2FV-C-A-7 Gear Pump (505000) Tuthill 4C2FV-C-A-7, Cast Iron Rotary Gear Pump. Pump End Only. 36 GPM C Series. Cast Iron Construction NO motor. Flange mount. Has Internal Relief Valve. Relief valve is set at 90 PSI (can be adjusted in field). Clockwise rotation only (from shaft end view). Tang Shaft. Inlet Port is 1-1/2 inch NPT, Discharge Port is 1-1/2 inch NPT.   Features : Pump Body:Cast Iron  Relief Valve:Relief valve is factory set to 90 PSI for adjustment between 30-225 PSI. Other PSI ranges available.  Shaft Seal:Sleeve Bushing Lip Seal Viton  Port Size:Inlet Port is 1-1/2 inch NPT Discharge Port is 1-1/2 inch NPT.

Oberdorfer 104M Series Centrifugal Pump FEATURES Pump Body: Bronze Ports: Inlet: 3/4" NPT Outlet: 1/2" NPT Flow: 24 GPM Max Pressure: to 23 PSI, 53 feet of head Impeller: Centrifugal Shaft Seal: Teflon Barrier Seal to Protect Motor Bearings. Carbon Face Mechanical Pump Seals. Buna Std., Viton and Teflon available. Shaft: 416 Stainless Steel is standard, Monel Shaft available for Marine Use Motor / Drive: Pump heads mount to standard footed NEMA 56J jet pump motors. A wide variety of motors are available and we can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED CENTRIFUGAL PUMP This close-coupled pump uses a standard NEMA C-Flange Jet Pump Motor with weld-on base and threaded shaft end to accept the pump impeller. The pump uses a mechanical type shaft seal with a Buna rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212 F. Viton® seals and Teflon seals (Chemlon) are available for severe solvents, difficult chemicals, and elevated temperatures. Will Handle Contaminated Liquids. Extremely Quiet. A Standard in the Marine Air Conditioning Industry.   Oberdorfer Centrifugal Pump 1/2HP ODP 115/230V Monel Shaft  

Oberdorfer 406M Series Flexible Impeller Macerator Pump Body: Bronze Ports: Inlet: 1 1/2" Threads Outlet 1" NPT or 1 1/2 Hose Flow: 25 GPM Max Pressure: 44 PSI Max, 100 feet of head Impeller: Neoprene Standard, Buna Optional Shaft Seal: Mechanical Seal Shaft: Stainless Steel Motor / Drive: These Close coupled Rubber Impeller Pumps are mounted directly onto the electric motor without the use of a shaft coupling. This pump is coupled to standard motors with Nema C flange. It uses a motor adapter plate to accommodate the pump. We can supply additional motors and assemble for you.         CLOSE COUPLED RUBBER IMPELLER MACERATOR PUMP BRONZE Portable. Compact. Easy Impeller Replacement. Macerator Easily Replaced. Reversible Wear Plate. Vacuum Switch Shut-off Pictured is Optional. Suction lifts of 15 ft. are possible when pump is fully primed.   Oberdorfer Flexible Impeller Macerator Pump, with 1HP, 24VDC, TEFC Motor, Painted White   This item is 'build to order'. Please contact us for lead time.

Applications for the TE-7K-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, deionized water systems, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.    March Pump's industrial TE-7K-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 53 gallons per minute at 10 feet, and its maximum head is 60 Feet (or around 26PSI). The standard wet end (the materials that come into contact with the solution) is composed of carbon filled Kynar (PVDF), Viton, Carbon, and Ceramic. The inlet connection is 1.5 inch female pipe thread, and the outlet is 1 inch male pipe thread. The standard motor is a 1 Phase 115/230V or 3 Phase 230/460V 0.75 Horsepower totally enclosed fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 75PSI, and the maximum liquid temperature is 200 Fahrenheit or 93 Celsius. The March TE-7K-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 53 GPM 180 LPM Max Head 60 FT 12.3 M Power .75 HP .559 KW Electrical 1PH 115/230V or 3PH 230/460V 50/60HZ     Type Centrifugal Mag Drive Inlet 1-1/2"FPT Outlet 1"MPT Wet End Carbon Filled Kynar (Front Housing, Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing) Motor Options Available in .75HP, 1HP, 1.5HP, 1HP Explosion Proof, or 1.5HP Explosion Proof

Little Giant Submersible Pump Little Giant 1-A Submersible Pump Small submersible oil-filled pump with epoxy coated cast aluminum housing. For commercial, industrial and home applications including statuary fountains, water displays, air conditioners, machine tool coolants, and many other applications where liquid must be transferred or recirculated. This compact 170 GPH pump features a 1/4" MNPT discharge, 7' shut-off head capability, and screened inlet. This pump is not recommended for aquariums, swimming pools and fuel oil transfer.   Features: 170 GPH @ 1 ft. Horespwoer 1/200, 115 Volt, 1.1 Amps Operates submersed. 6' cord Epoxy-coated aluminum housing Bottom inlet has snap-off screen for easy cleaning. 1/4" MNPT outlet, with 90° elbow accessory, accepts 1/2" I.D. tubing