ZCI™ Zero Contact Interface Universal Trailer Light Power Modulite® Wiring Kit Wiring Kit for Installing #119146, #119147, #119176, #119177, #119179, #119180, #119190, #119192 ModuLite® Power Modules, Includes 20 ft. Undercar Wire, Fuse w/Holder and Attaching Terminals Features: Wiring kit for installing all Modulites Includes 10 AMP fuse WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ZCI™ Zero Contact Interface Universal ModuLite® - Universal Trailer Light Power Module ZCI sensor technology and direct connection to the tow vehicle battery, eliminates all electrical connection and interference with the tow vehicle electrical system. Vehicles with 12 volt system only. Features: NO CUTTING OR SPLICING VEHICLE WIRING! Isolates Trailer Light Operation from Tow Vehicle's Electrical System Works with 2 or 3 wire systems Works with PWM or Multiplexed systems requiring 2 or 3 wire hookup Rated for up to 4.2 amps for turn/stop & 7.5 amps for taillight trailer circuits Works with low side switched vehicles Integrated auto resetting short & overload protection Robust design allows for interior or exterior mounting WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

ZCI™ Zero Contact Interface Universal ModuLite® & Installation Kit ZCI sensor technology and direct connection to the tow vehicle battery, eliminates all electrical connection and interference with the tow vehicle electrical system. Vehicles with 12 volt system only. Features: No cutting or splicing vehicle wiring Isolates Trailer Light Operation from Tow Vehicle's Electrical System Works with 2 or 3 wire systems Works with PWM or Multiplexed systems requiring 2 or 3 wire hookup Rated for up to 4.2 amps for turn/stop & 7.5 amps for taillight trailer circuits Works with low side switched vehicles Integrated auto resetting short & overload protection Robust design allows for interior or exterior mounting WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Safety First when it comes to Trailer Lighting   Safety is important, not only on the water, but on the road going to and coming from the water. If your trailer is more than a few years old, most likely you have had or are having some issues with the lights and the electrical system on your trailer. Fortunately, most issues are pretty easy to fix.   The first thing to do is to test the lights by hooking up to the vehicle harness and checking all lights to make sure they are bright and working. If any are dim or not functioning, connect a tester to the vehicle harness to see if there might be an issue with the electrical source. Cleaning the connectors of the harness on both the vehicle and trailer side is critical, and can easily be done with a can of electrical connector spray and a fine wire brush. Also, clean the ground contact and tighten the ground wire.   Make sure to check the ground screw and replace it if it is corroded. Most bulbs are easily replaceable by simply twisting them to remove and install them. You can also clean up corroded sockets by gently sanding away the corrosion with fine sandpaper. It's possible you may have to replace wiring, which can be purchased as part of a complete kit that includes new lights, connectors, and lenses. We suggest if you do not have LED light on your trailer to switch over to them. Led lights are brighter, more efficient and has multiply bulbs so you will never have a taillight completely unlit if one bulb burns out.   CLR Marine carries trailer lights and lighting kits, which are complete with license plate holder, wiring and side lights. Along with any other trailer accessory you may need.       Specials   Closeouts    Remanufactured    Rebates  

Universal Bumper Wiring Kit 6' for Trailer Winches 6' of 8-gauge wire 6' of 12-gauge wire T-Style Handle

Submersible Trailer Light Kit Applicable to trailers under 80 inches wide. Ideal for utility, snowmobile, camping, motorcycle, and boat trailers. Design conforms to applicable US FMVSS and Canadian CMVSS safety standards. Complete Kit Includes:  A pair of 8-function stop/tail/turn lights, wiring harness, and license plate bracket

Low-Profile Submersible Trailer Light Kit Low profile for trailers over 80 inches wide. Ideal replacement lights for most boat trailers. Conforms to applicable U.S. FMVSS and Canadian CMVSS safety standards.  Kit Includes: (2) multi-function lamps  Wiring harness  License plate bracket and mounting hardware

Submersible LED Trailer Light Kit For use with trailers under 80 inches wide. Conforms to applicable U.S. FMVSS and Canadian CFMVSS standards. Kit Includes: (2) multi-functional (stop/tail/turn) submersible LED trailer lights  License plate bracket Wiring harness and installation hardware

Submersible LED Low-Profile Trailer Light Kit Ideal replacement or upgrade for most trailers. Conforms to applicable U.S. FMVSS and Canadian CFMVSS standards. Kit Includes: Includes (2) multi-functional (stop/tail/turn) submersible low-profile LED trailer lights  License plate bracket  Wiring harness and installation hardware

Color Caster Extended Multi-Color Underwater Light - 10' Lead Wire The SCM-10-EXT-CC extended color underwater light provides your vessel with 42 watts of intense LED lighting. Easily switch between 12 standard colors or use an or use a Shadow-NET® enabled product to enjoy unlimited colors. The SCM-10-EXT-CC’s low profi le design allows for many mounting locations. The unique stainless steel housing compliments the look of any trailer or lift kept boat. Features: Proprietary clear-gel-fi lled design, injected through entire unit —eliminates condensation and/or water intrusion under stress Tough, polycarbonate lens  Passivated stainless steel 316 material provides a durable corrosion resistant housing Transient surge and reverse polarity protection — dramatically prolongs unit life Thermal throttling technology —enables safe operation even out of water From simple on-off to full-feature lighting effects, unit is enabled for a host of control interfaces Select between 12 colors when using a switch or unlimited colors when using Shadow-NET® enabled products Specifications: Up to 3,750 lumens 120 degree beam angle 42 watts power draw 3.5 amps operating current draw @ 12 volts 10-30 volts input 10” (254 mm) x 2.4” (61mm) x 0.5” (13mm) IP68 fully submersible waterproof design 10 RGBW LEDs Includes: Lighting unit 10’ (6 m) submersible-grade cable 2 SS316 1” #8 PH screws Standard 2 year warranty

Hydro Power Amplifier Install Kit - 4GA High quality wiring at it's best!  This DS18 wiring kit comes with everything you need to install your new amplifier.  OFC stands for oxygen free cooper which is the standard in wiring for the audio world. Stronger, more conductive, and corrosion resistant are the main benefits of our OFC kits.  These kits include power, ground, and remote OFC wiring all encased in our ultra tough marine grade insulation.   Also included are RCA's, fuse size label on wiring, and waterproof fuse holder. Features: 4GA - Up to 1800 watts Oxygen free tin copper wires Marine grade ATC Fuse holder In the Box: Waterproof Fuse Holder 17' of 4GA White Power Tin OFC Cable 17' of 4GA Black Ground Tin OFC Cable 17' of Red/Black RCA Tin OFC Cable with Metal Plugs 17' of Blue Remote Tin OFC Cable 1 x 80A Fuse (up to 960 watts) 1 x 100A Fuse (up to 1200 watts) 1 x 150A Fuse (up to 1800 watts) 10 x Cable Ties 2 x Ring Terminals 4 x 10 AWG End Sleeves (Silver Plating) 4 x 8 AWG End Sleeves (Silver Plating) 3 x Allen Keys (2mm, 1.4mm and 1.3mm) Instruction Manual ∗Sold as Individual Piece

Hydro Power Amplifier Install Kit - 8GA   High quality wiring at it's best!  This DS18 wiring kit comes with everything you need to install your new amplifier.  OFC stands for oxygen free cooper which is the standard in wiring for the audio world. Stronger, more conductive, and corrosion resistant are the main benefits of our OFC kits.  These kits include power, ground, and remote OFC wiring all encased in our ultra tough marine grade insulation.   Also included are RCA's, fuse size label on wiring, and waterproof fuse holder. Features: 8GA - Up to 960 watts Oxygen free tin copper wires Marine grade ATC Fuse holder In the Box:  Waterproof Fuse Holder 17' 8GA White Power Tin OFC Cable 17' 8GA Black Ground Tin OFC Cable 17' Red/Black RCA Tin OFC Cable with Metal Plugs 17' Blue Remote Tin OFC Cable 2 x 30A fuses (up to 720 watts) 2 x 40A fuses (up to 960 watts) 10 x Cable Ties 2 x Ring Terminals 4 x 10 AWG End Sleeves (Silver Plating) 4 x 8 AWG End Sleeves (Silver Plating) 2 x Allen Keys (2mm and 1.3mm) Instruction Manual ∗Sold as Individual Piece

V10-2041 4 Gauge Amp Wiring Kit - 20' (6.1 M) A marine amplifier has to stand up to the rigors of life on the water, and so does the wiring kit you use with it.  The T-Spec V10-2041 Amp Kit is ideal for most single marine amps with a power rating of up to 1000 watts and will give you reliable power for seasons to come. Features: Complete marine amplifier wiring kit Includes power wire, ground wire, turn-on wire, circuit breaker, ring terminals, wire ties, and more Marine-compliant cable In the Box: 4 AWG pearl White OFC copper wire - 20' 4 AWG matte Grey OFC copper wire - 20' 18 AWG Blue wire - 20' (1) 100 amp circuit breaker (1) 1/0 AWG ring terminal with White boot (1) 1/0 AWG ring terminal with Silver boot (10) 6" Wire ties *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

V10-1041 4 Gauge Amp Wiring Kit - 10' (3.05 M) A marine amplifier has to stand up to the rigors of life on the water, and so does the wiring kit you use with it.  The T-Spec V10-1041 Amp Kit is ideal for most single marine amps with a power rating of up to 1000 watts and will give you reliable power for seasons to come. Features: Complete marine amplifier wiring kit Includes power wire, ground wire, turn-on wire, circuit breaker, ring terminals, wire ties, and more Marine-compliant cable In the Box: 4 AWG pearl White OFC copper wire - 10' 4 AWG matte Grey OFC copper wire - 10' 18 AWG Blue wire - 20' (1) 100 amp circuit breaker (1) 1/0 AWG ring terminal with White boot (1) 1/0 AWG ring terminal with Silver boot (10) 6" Wire ties *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Trailer Connector-Flat 4-Wire - 12" Loop Molded trailer connector made in accordance with SAE color coding.  Features: Male Connector for Trailer Side/Female Connector for Vehicle Side Loops can be cut to the desired length for splicing into an existing wire assembly 12" Wire Loop - 16 AWG 4-contact connectors are molded with an EasyGrip for fast and easy disconnect