Large Gunnel Mount Backing Plates f/88506 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Large Side Mount Backing Plates f/88508 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Gunnel Mount Backing Plates f/88502 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Side Mount Backing Plates f/88505 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Sidewinder Backing Plate f/Bolt-In Holders Below top operation. Fully locked in Running and 80° out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. Available with Quick Laydown or Curved Tube. No ball bearings to rust. Internal Delrin and nylon bearing surfaces provide smooth operation and prevent metal to metal contact. Accepts our 16Ft Extra Strong (AP3916XS) or 18Ft (AP3918) Outrigger Pole. Has 4"x6" Mounting plate. Extends 14" above and 8-1/2" below mounting plate. Fits all outrigger ready boats.

RH5930 Stainless Steel Backing Plate for 0°, 15° & 30° Heavy Rod Holders.

RH5931 Stainless Steel Backing Plate for 0°, 15° & 30° Medium Rod Holders.

441 Backing Plate f/241 & 244 Mount Use the Scotty Backing Plate to add structural support when attaching the Scotty 241L / 241 Combination Side / Deck Mount or the Scotty 244L / 244 Flush Deck Mount to thin-walled watercraft. Made with super tough, rugged engineering grade nylon. *Stainless steel nuts & machine screws included. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Backing Plate for 70 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series. Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plate for 80 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plates For Grand Slam Outriggers (pair) Part #: BP-150BSY-320-1 Specifically made for additional support for Grand Slam Outriggers when mounting to hard tops and gunnels. Made of Anodized Aluminum.

Striker Base Gunnel Mount F16-0150-F The TACO Striker skiff flush mount base is the strongest gunnel mount base on the market today. 12 locking positions with our hex nut design including stand up and lay down. Manufactured to very high standards using marine grade cast 316 stainless steel. Ambidextrous arms. (will fit both port and starboard bases). Welded locking adapter for maximum strength. Removable arms for unobstructed decks. Template included for installation. Bases compatible with Lee™, Perko™, & Rupp™ outrigger poles

Dashboard Mount with Backing Plate for 7"-8" Tablets with Cases The RAM® Tab-Tite™ bundle is a rugged mount including the RAM® Tab-Tite™, RAM® Universal Double Ball Mount with Two Round Plates, and RAM® Backing Plate Adapter. The RAM® Tab-Tite™ spring-loaded, quick-release holder offers a secure fit with easy access to the mounted tablet. The spring-loaded design makes it easy to insert and remove your tablet, along with keeping it secure in mobile applications. The custom end cups are designed to optimize the functionality of your tablet, enabling access to all ports and tablet functions. The RAM-101U-B consists of a short double socket arm and two 2.5" diameter round bases with the universal AMPS hole pattern. Designed into the mount is a 1.5" diameter patented rubber ball and socket system with adjustment points at both socket ends of the arm. Rubber ball and socket technology allow for almost infinite adjustment and perfect viewing angles. The included 2.10" x 2.60" steel backing plate with #8-32 threaded holes attaches to a variety of RAM® Mounts ball bases. Features: The spring-loaded holder secures 7 in. -8 in. tablets with a case; interchangeable end cups allow you to modify the holder when upgrading devices Drill-down mounting solution; choose either round plate featuring the AMPS hole pattern for attachment to compatible device holders 2.10 in. x 2.60 in. steel backing plate attaches to a variety of RAM® Mounts ball bases Ball and socket technology allows for near-infinite adjustability Backed by a lifetime warranty Specifications: Hardware Included: Assembly Hardware, (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Holder Dimensions (inch): Height Range: 8.32" - 10.92", Width Range: 4.43" - 5.3", Depth Range: .13" - .62" Socket to Socket Length (inch): 2.5” Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum, high-strength composite, powder-coated steel Weight: 1.98 lb. Compatible Devices: Samsung: Galaxy Tab 4 8.0 with Otterbox Defender Case, Galaxy Tab A 8.0 (2017) with Case, Galaxy Tab A 8.0 (2018) with Case, Galaxy Tab A 8.0 (2019) with Case, Galaxy Tab S 8.4 with Otterbox Defender Case, Galaxy Tab E 8.0 with Verizon Rugged Case, and Galaxy Tab Active2

X-Grip® Dashboard Mount with Backing Plate for 9"-10" Tablets The RAM® X-Grip® universal holder for 9"-10" tablets features an 'X' design that expands and contracts to provide a perfect fit for your device – even if it's in a case. Included are easy-access grip knobs located on the back of the holder for quick release of your tablet. No matter what double socket arm and mounting base you pair the RAM® X-Grip® with, RAM® ball and socket technology allow for near-infinite adjustability to achieve the ideal viewing angle while also extending the life of your tablet by providing shock and vibration damping. The RAM-101U-B consists of a short double socket arm and two 2.5" diameter round bases with the universal AMPS hole pattern. Designed into the mount is a 1.5" diameter patented rubber ball and socket system with adjustment points at both socket ends of the arm. Rubber ball and socket technology allow for almost infinite adjustment and perfect viewing angles. Features: Spring-loaded 'X' design with rubber caps sports great holding power without obstructing your tablet; fits most 9 in. -10 in. tablets Drill-down mounting solution; choose either round plate featuring the AMPS hole pattern for attachment to compatible device holders 2.10 in. x 2.60 in. steel backing plate attaches to a variety of RAM® Mounts ball bases Made of high-strength composite and steel components for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: Assembly Hardware, (1) 2.10" x 2.60" Steel Backing Plate, (4) #8-32 x 1" Screws, (4) #8 Split Lock Washers, and (4) #8 Flat Washers Holder Dimensions (inch): Max Height: 10.25" (using optional supports), Width Range: 6.25" - 8.1", and Max Depth: .875" Socket to Socket Length (inch): 2.5” Hole Pattern (inch): 4-Hole AMPS: 1.181" x 1.496", 3-Hole 120-Degree: 1.812" Diameter Plate Size (inch): 2.5" Diameter Ball Size (inch): C size (1.5”) Weight Capacity: The standard use is 4 lbs. and the heavy-duty use is 3 lbs. Materials: Marine-grade aluminum and high-strength composite Weight: 2.42 lb. Compatible Devices: Amazon: Fire HD 10 Apple: iPad (1st Generation), iPad (3rd Generation), iPad (4th Generation), iPad (5th Generation), iPad (6th Generation), iPad (7th Generation), iPad (8th Generation), iPad (9th Generation), iPad (10th Generation), iPad 2, iPad 9.7 (2017), iPad 9.7 (2018), iPad Air, iPad Air 2, iPad Air 3, iPad Air 4, iPad Air 5, iPad Pro 9.7 (1st Generation), iPad Pro 10.5 (2nd Generation), iPad Pro 11", iPad Pro 11" (2020), iPad Pro 11" (2021), and iPad Pro 11" (2022) ASUS: MeMO Pad FHD 10, Transformer Pad, ZenPad 10, ZenPad 3S 10, and ZenPad Z10 Dell: Venue 10 7000, Venue 11 Pro, and Venue 11 Pro 7000 Google: Nexus 10 and Pixel C HP: ElitePad 900, ElitePad 900 G1, Pro 610, and Pro Slate 10.1 Huawei: MediaPad M2 10.0, MediaPad M3 Lite 10.0, and MediaPad T3 10 Lenovo: Miix 3, Tab P12 Pro, S6000, Tab 2 A10-70, Tab 4 10, Tab 4 10 Plus, Tab A10, Tab3 10 Business, ThinkPad 10, ThinkPad Tablet 2, Yoga Book, Yoga Tab 3 10, Yoga Tab 3 Pro, Yoga Tablet 10, Yoga Tablet 10 HD+, and Yoga Tablet 2 (10 inches) LG: G Pad 10.1, G Pad II 10.1, G Pad X 10.1, and G Pad X II 10.1 Microsoft: Surface 2, Surface Pro, Surface Pro 2, Surface Go, and Surface Go 2 Nokia: T21 Samsung: Galaxy Book 10.6, Galaxy Tab 10.1, Galaxy Tab 2 10.1, Galaxy Tab 3 10.1, Galaxy Tab 4 10.1, Galaxy Tab A 9.7, Galaxy Tab A 10.5, Galaxy Tab A8 10.5, Galaxy Tab Active Pro, Galaxy Tab Active4 Pro, Galaxy Tab Pro 10.1, Galaxy Tab S 10.5, Galaxy Tab S2 9.7, Galaxy Tab S3 9.7, Galaxy Tab S4 10.5, Galaxy Tab S5e, Galaxy Tab S6, Galaxy Tab S7, Galaxy Tab S7 FE, Galaxy Tab S7 Plus, Galaxy Tab S8, and Galaxy Tab S8 Plus Sony: Vaio Tap 11, Xperia Tablet S, and Xperia Tablet Z Vankyo: MatrixPad Z4 10" Zebra: ET50 10" and ET55 10"

Striker Bases Gunnel Mount F16-0212-F The TACO Striker skiff flush mount base is the strongest gunnel mount base on the market today. 12 locking positions with our hex nut design including stand up and lay down. Manufactured to very high standards using marine grade cast 316 stainless steel. Ambidextrous arms. (will fit both port and starboard bases). Welded locking adapter for maximum strength. Removable arms for unobstructed decks. Template included for installation. Accept TACO 1-1/8" Tele-Outriggers Bases also compatible with Lee™, Perko™, & Rupp™ outrigger poles