Gunnel Mount Backing Plates f/88502 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Large Gunnel Mount Backing Plates f/88506 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Side Mount Backing Plates f/88505 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Large Side Mount Backing Plates f/88508 Outrigger Holder - Pair Made of heavy gauge stainless steel. Sized for cast outrigger holders only.

Sidewinder Backing Plate f/Bolt-In Holders Below top operation. Fully locked in Running and 80° out Trolling positions. Locks when handle is up or down. Rotates when handle is to the left or right. Fastest Lay-Down on the market. Automatically locks in position when raising or lowering the pole. No knobs to loosen or tighten. Just pull down the Ridged Collar and lower or raise the pole. Available with Quick Laydown or Curved Tube. No ball bearings to rust. Internal Delrin and nylon bearing surfaces provide smooth operation and prevent metal to metal contact. Accepts our 16Ft Extra Strong (AP3916XS) or 18Ft (AP3918) Outrigger Pole. Has 4"x6" Mounting plate. Extends 14" above and 8-1/2" below mounting plate. Fits all outrigger ready boats.

Backing Plate for GS-850 & GS-950 To provide strength for your Grand Slam 850 and 950 when installed to your T-top, our TACO Grand Slam Backing Plates are the answer.  Features: Provides strength to base Matches existing base hole pattern No drilling Attractive addition to your T-top 5-year limited warranty

RH5930 Stainless Steel Backing Plate for 0°, 15° & 30° Heavy Rod Holders.

RH5931 Stainless Steel Backing Plate for 0°, 15° & 30° Medium Rod Holders.

441 Backing Plate f/241 & 244 Mount Use the Scotty Backing Plate to add structural support when attaching the Scotty 241L / 241 Combination Side / Deck Mount or the Scotty 244L / 244 Flush Deck Mount to thin-walled watercraft. Made with super tough, rugged engineering grade nylon. *Stainless steel nuts & machine screws included. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Gunnel Mount Outrigger Holder - Fabricated 304 S.S. - 1-1/8" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Gunnel Mount Outrigger Holders - Cast 316 S.S. - 1-1/8" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Gunnel Mount Outrigger Holders - Cast 316 S.S. - 1-1/2" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Backing Plate for 70 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series. Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plate for 80 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plates For Grand Slam Outriggers (pair) Part #: BP-150BSY-320-1 Specifically made for additional support for Grand Slam Outriggers when mounting to hard tops and gunnels. Made of Anodized Aluminum.