TigerShark I LineRigger® Electric Top Mount Outrigger Holders f/1-1/2" Poles - Pair Designed for Hard or Soft T-Tops Finally the first top mount outrigger holder that is electronically operational right at your console. This is a one-man operation to deploy, raise, lower and retrieve your outriggers with a simple push of a switch. Crafted of marine aluminum, highly polished and Anodized for years of service.  Package included 2 - 12' wire harnesses and one dual rocker switch panel Features: The simplicity of pressing a switch and you're fishing! The TigerShark I LineRigger® is the first electronically operated top mount outrigger holder offered in the market Meticulous engineering provides exact electronic deployment of your outriggers from your console The powerful 12V motor drive allows for the total deployment and/or adjustment by simply pressing the switch up for deploying or pressing the switch down for retrieval of your outriggers Fits all prepared t-tops with 3" Mounting Hole Mounting Plate Size: 4" W x 6" L Includes 12' of wire from each holder Units are supplied with a standard dual rocker switch panel  When activated simultaneously, it raises and deploys your outriggers to the fishing position Convenience, craftsmanship, quality and performance will make the TigerShark a top selection for the sports-fisherman

TigerShark III LineRigger® Manual Top Mount Outrigger Holder f/1-1/2" Poles-Pair For Hard or Soft Tops This TigerShark series features the lowest profile under your top. Simply push the handle up to release the gears and turn 14 to 17 times for complete deployment of your outriggers to maximum bait spread. Then, simply pull the handle down and lock into place. Simultaneous up and out motion eliminates climbing the gunnels to adjust your outriggers. A simple turn of the handle does it all- total deployment and total position adjustment. Features: Bottom mounted crank assembly for ease of deployment Simply push up on the handle to release the gears and turn 14 to 17 times to complete deployment of your outriggers, then simply pull handle down to lock into place Simultaneous up and out motion eliminates climbing the gunnels to adjust your outriggers Fits all prepared t-tops with 3" Mounting Hole Fits Hard tops up to 2 1/2" thick Allowing for the lowest profile under your t-top or hard top of any top mount outrigger holder in the industry

Gunnel Mount Outrigger Holders - Cast 316 S.S. - 1-1/8" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Side Mount Outrigger Holders - Fabricated 304 S.S. - 1-1/8" I.D.-Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Side Mount Outrigger Holders - Cast 316 S.S. - 1-1/8" I.D.-Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Gunnel Mount Outrigger Holder - Fabricated 304 S.S. - 1-1/8" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Gunnel Mount Outrigger Holders - Cast 316 S.S. - 1-1/2" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Side Mount Outrigger Holders - Cast 316 S.S. - 1-1/2" I.D.- Pair Our premium quality stainless steel outrigger holders are fabricated to our quality standards for years of service. All Tigress products are proven salt water worthy. For best installation, use our backing plates 88502-1 or 88505-1. For replacement tubes use 88501 or 88503.

Z-30 Top Gun Outrigger Kit - 15' Buy Rupp's complete Outrigger System and save money. The Rupp Sportfishing kits make it simple to have your boat ready to fish upon receipt. If your boat came "outrigger ready" with a Rupp outrigger mounting plate or similar plate from TACO or E-TEC Marine - your ready to bolt in a Rupp Outrigger and go. This package comes complete with a pair of Z-30 Bolt-In Top Gun Radial bases, a pair of 15' Telescoping poles and a complete single line rigging kit with Klicker release clips. Top Gun Telescoping Poles - 15' Pair Our 15 foot telescoping pole is comprised of three sections making it the most rigid and durable telescoping pole on the market. Very little flex and robust buttons make Rupp telescoping poles an obvious choice. Our telescoping poles are an ideal match for any of our Top Gun outrigger bases. Every part of these telescoping poles are fully serviceable, easy replaceable and made in the USA. O.D of outrigger base tube is 1.50", designed to fit perfectly into Rupp outrigger bases. Top Gun Bolt-In Z-30 Bases - Pair An innovative advance in Top Gun engineering, Rupp's Z-30 gear drive system offers unmatched ease of operation for top mount outriggers. Simply turning the palm-size handle deploys and retrieves riggers smoothly and effortlessly with an outstanding 30 to 1 advantage. Z-30 Top Guns are engineered for durability with a high strength, forged aluminum body that protects cutting edge components. Now with anodized aluminum knob and other enhancements. Forged 4" x 6" mounting flange provides ease of BOLT-IN installation and below top operation. Designed to accept Rupp Top Gun poles in 15' or 18'. Top Gun Rigging Kit w/Klickers Complete rigging packages that allow you to run One (1) lines on each rigger. this kit includes (2) exclusive Rupp single pulley shock cords, 50ft of white braided nylon halyard lines one pair of Rupp KLICKER release clips. (2) Nylon ball stops, (2) Strap Eyes, (4) Snap Swivels, (2) Swivels. This rigging kit is for small outriggers, 20' and under.

Outrigger Holder Reducer - 1-7/8" to 1-1/2" - Pair Downsize your outrigger holders Reduce from 1-7/8" to 1-1/2"

Outrigger Holder Reducer - 1-1/2" to 1-1/8" - Pair Downsize your outrigger holders Reduce from 1-1/2" to 1-1/8"

Rupp Outrigger Supports W/2" Offset - Pair Take the stress off of your hardtop and outrigger radial joint. Extends the life of your outriggers and bases by reducing outrigger movement while underway. This is a great choice for new or old T-Top mounted outriggers, designed with a 2" offset . Made from high impact injection molded plastic, fits 1.5" diameter outriggers, now with a retaining strap that firmly grabs the outrigger. Sold in pairs. Support "clevis" designed to accept pole diameter up to 1.50".

Side Mount Outrigger Holders OH2020S Size: 2.0" Dimensions: 4 3/4 x 7 1/2 Side Mount Bracket utilizes same curved tube as Gunnel Mount. One piece Bracket construction. Tube, Feet and Bar-Pin are all cast simultaneously for the ultimate in strength. Unit provides same three positions as Flush Mount. Same rugged Chrom on Brass Cosntruction. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Straight Side Mount Transom Rod or Console Rod Holder 8-1/2" Features: 4 hole 3" x 4-1/2" brushed pad Constructed of cold drawn anodized aluminum WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Flojet 20381-000 Kit Port 1/2" Quest (Pair)  Flojet Snap-In Quad Port Kit with EPDM O-Ring 1/2" Quest Thread Straight (pair)