Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Globe Impeller Model 125 RED Globe Impeller Model 125 RED Replaces the following impellers Ancor J050405 CEF 500205 Jabsco 18021-0003, 836-0003, 836-0008 Johnson Pump 09-1029B-9 Sierra Marine 18-3037 Weight: 0.6 lbs. Od (in/mm): 3 3/4" / 95 Width (in/mm): 2 1/2" / 63 Shaft Size (in/mm): 1" / 25 Drive Type: 12 pt Spline Core Type: Composite Number of Blades: 9 Silhouette Letter: O Fuel Type: Diesel Includes matching Gaskets or O-rings For Diesel and Oil Applications Only

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

2" Bronze Pedestal Pump Flow rate: Nominal 60 gallons/min at 1500 rpm Self-priming from dry up to 7.8ft Features: Constructed from marine quality bronze and stainless steel for ruggedness and reliability. Easy to service and maintain. Inexpensive to buy and operate. Will tolerate abrasive wear (this may affect performance - seek advice from your distributor). Handles hard and soft solids without clogging. Can pump in either direction. Will not airlock. APPLICATIONS MARINE: Engine cooling, pumping bilges, wash downs, circulating water in bait tanks, utility dock side pump. INDUSTRIAL: Circulating and transferring, Velocity-mixing, Return spill, Sump drainage, Chemicals, Pharmaceuticals, Soap, Liquors, Inks, Dyes, Alcohol, Tanning Liquors, Glycerin, Brine, etc. FARMING: Pumping water for stock, Pumping water from shallow wells and cisterns. WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer, and LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

9 amp stators for 2, 3, 4 and 6 cylinder outboard engines.

Inverter 24VDC - 250VA - 120VAC - VE.Direct - NEMA 5-15R Inverters allow you to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V, or 48VDC.  The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook, and other devices (VE.Direct Bluetooth Smart dongle needed) Fully configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load, and alarms Please get in touch with your dealer for any returns, repairs, or support issues related to this product. Phoenix Inverter 24/250 Specifications: Continuous Power at 25°C: 250VA Continuous Power at 25°C / 40°C: 200 / 175W  Peak Power: 400W  Output AC Voltage / Frequency (adjustable): 120VAC +/- 3% Input Voltage Range: 9,2 - 17 / 18,4 - 34,0 / 36,8 - 62,0V DC Low Shut Down (adjustable): 9,3 / 18,6 / 37,2V Dynamic (Load Dependent) DC low shut down (fully configurable): Dynamic cut-off DC Low Restart and Alarm (adjustable): 10,9 / 21,8 / 43,6V Battery Charged Detect (adjustable): 14,0 / 28,0 / 56,0V Maximum Efficiency: 87 / 88 / 88%  Zero-Load Power: 4,2 / 5,2 / 7,9W  Default Zero-Load Power in ECO Mode (default retry interval: 2,5 s, adjustable): 0,8 / 1,3 / 2,5W ECO Mode Stop and Start Power Setting: Adjustable Protection: a - f Operating temperature Range: -40 to +65°C (fan-assisted cooling) / Derate 1,25% per °C above 40°C Humidity (non-condensing): Max 95% Enclosure: Material & Color: Steel chassis and plastic cover (blue Ral 5012) Battery-Connection: Screw terminals Maximum Cable cross-Section 10mm^2 / AWG8  Standard AC outlets 230V: Schuko (CEE 7/4), IEC-320 (male plug included), UK (BS 1363), AU/NZ (AS/NZS 3112), 120V: Nema 5-15R, GFCI Protection Category: IP 21 Weight: 2,4kg / 5,3lbs Dimensions (h x w x d, mm) / (h x w x d, inch): 86 x 165 x 260 mm / 3.4 x 6.5 x 10.2 in. Accessories: Remote On-Off: Yes Automatic Transfer Switch: Filax

Myers Pumps 05014A158 Gasket RUBBER GASKET 6 3/4 X 6 1/2 X 1/8

Phoenix Inverter 12/250 - 120V - VE.Direct GFCI Duplex Outlet - 200W Inverters allow users to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V or 48V DC. *This inverter has a GFCI Duplex Outlet. E.Direct Communication Port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook, and other devices (VE.Direct Bluetooth Smart dongle needed) Fully Configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load, and alarms Proven Reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short-circuit proof and protected against overheating, whether due to overload or high ambient temperature. High Start-Up Power Needed to start loads such as power converters for LED lamps, halogen lamps, or electric tools. ECO Mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once on standby, the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote On/Off A remote on/off switch can be connected to a two-pole connector, or between battery plus and the left-hand contact of the two-pole connector. LED Diagnosis Please see the manual for a description. To Transfer the Load to Another AC Source: The Automatic Transfer Switch For Victron’s low-power inverters, they recommend the Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.  Inverter Specifications: Cont. Power at 25 degrees C: (1) 250VA  Cont. Power at 25 degrees C / 40 degrees C: 200 / 175W  Peak Power: 400W  Output AC Voltage / Frequency (adjustable): 230VAC or 120VAC +/- 3% 50Hz or 60Hz +/- 0,1% Input Voltage Range: 9,2 - 17 / 18,4 - 34,0 / 36,8 - 62,0V DC Low Shut Down (adjustable): 9,3 / 18,6 / 37,2V Dynamic (load dependent) DC Low Shut Down (fully configurable): Dynamic cut-off, see https://www.victronenergy.com/live/ve.direct:phoenix-inverters-dynamic-cutoff DC Low Restart & Alarm (adjustable): 10,9 / 21,8 / 43,6V Battery Charged Detect (adjustable): 14,0 / 28,0 / 56,0V Max. Efficiency: 87 / 88 / 88%  Zero-Load Power: 4,2 / 5,2 / 7,9W  Default Zero-Load Power in ECO Mode (default retry interval: 2,5 s, adjustable): 0,8 / 1,3 / 2,5W  ECO Mode Stop & Start Power Setting: Adjustable Protection (2): a - f Operating Temperature Range -40 to +65 degrees C (fan-assisted cooling)  Enclosure Specifications: Material & Color: Steel chassis and plastic cover (blue Ral 5012) Battery-Connection: Screw terminals Maximum Cable Cross-Section: 10mm² / AWG8  Standard AC Outlets: 230V: Schuko (CEE 7/4), IEC-320 (male plug included); UK (BS 1363), AU/NZ (AS/NZS 3112); 120V: Nema 5-15R, GFCI Protection Category: IP 21 Weight: 2,4kg / 5,3lbs  Dimensions (H x W x D, mm); (H x W x D, inch): 86 x 165 x 260; 3.4 x 6.5 x 10.2 Accessories: Remote On-off: Yes Automatic Transfer Switch: Filax Standards: Safety: EN-IEC 60335-1 / EN-IEC 62109-1 / UL 458 (3) EMC: EN 55014-1 / EN 55014-2 / IEC 61000-6-1 / IEC 61000-6-2 / IEC 61000-6-3 Automotive Directive ECE R10-4: 1) Nonlinear load, crest factor 3:1; 2) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) DC ripple too high Please contact your dealer for any returns, repairs or support issues related to this product.

Phoenix Inverter 12/250 - 120V - VE.Direct NEMA 5-15R - Single Outlet - 200W Inverters allow users to power domestic equipment - requiring 230V/120V AC - using 'leisure' or 'automotive' batteries rated at 12V, 24V or 48V DC.  *This inverter has a NEMA 5-15R outlet.  E.Direct Communication Port The VE.Direct port can be connected to: A computer (VE.Direct to USB interface cable needed) Apple and Android smartphones, tablets, MacBook, and other devices (VE.Direct Bluetooth Smart dongle needed) Fully Configurable: Low battery voltage alarm trip and reset levels Low battery voltage cut-off and restart levels Dynamic cut-off: load-dependent cut-off level Output voltage 210 - 245V Frequency 50 Hz or 60 Hz ECO mode on/off and ECO mode sense level Monitoring: In- and output voltage, % load, and alarms Proven Reliability The full bridge plus toroidal transformer topology has proven its reliability over many years. The inverters are short-circuit proof and protected against overheating, whether due to overload or high ambient temperature. High Start-Up Power Needed to start loads such as power converters for LED lamps, halogen lamps, or electric tools. ECO Mode When in ECO mode, the inverter will switch to standby when the load decreases below a preset value (min load: 15W). Once on standby, the inverter will switch on for a short period (adjustable, default: every 2,5 seconds). If the load exceeds a preset level, the inverter will remain on. Remote On/Off A remote on/off switch can be connected to a two-pole connector, or between battery plus and the left-hand contact of the two-pole connector. LED Diagnosis Please see the manual for a description. To Transfer the Load to Another AC Source: The Automatic Transfer Switch For Victron’s low-power inverters, they recommend the Filax Automatic Transfer Switch. The Filax features a very short switchover time (less than 20 milliseconds) so that computers and other electronic equipment will continue to operate without disruption.  Inverter Specifications: Cont. Power at 25 degrees C: (1) 250VA  Cont. Power at 25 degrees C / 40 degrees C: 200 / 175W  Peak Power: 400W  Output AC Voltage / Frequency (adjustable): 230VAC or 120VAC +/- 3% 50Hz or 60Hz +/- 0,1% Input Voltage Range: 9,2 - 17 / 18,4 - 34,0 / 36,8 - 62,0V DC Low Shut Down (adjustable): 9,3 / 18,6 / 37,2V Dynamic (load dependent) DC Low Shut Down (fully configurable): Dynamic cut-off, see https://www.victronenergy.com/live/ve.direct:phoenix-inverters-dynamic-cutoff DC Low Restart & Alarm (adjustable): 10,9 / 21,8 / 43,6V Battery Charged Detect (adjustable): 14,0 / 28,0 / 56,0V Max. Efficiency: 87 / 88 / 88%  Zero-Load Power: 4,2 / 5,2 / 7,9W  Default Zero-Load Power in ECO Mode (default retry interval: 2,5 s, adjustable): 0,8 / 1,3 / 2,5W  ECO Mode Stop & Start Power Setting: Adjustable Protection (2): a - f Operating Temperature Range -40 to +65 degrees C (fan-assisted cooling)  Enclosure Specifications: Material & Color: Steel chassis and plastic cover (blue Ral 5012) Battery-Connection: Screw terminals Maximum Cable Cross-Section: 10mm² / AWG8  Standard AC Outlets: 230V: Schuko (CEE 7/4), IEC-320 (male plug included); UK (BS 1363), AU/NZ (AS/NZS 3112); 120V: Nema 5-15R, GFCI Protection Category: IP 21 Weight: 2,4kg / 5,3lbs  Dimensions (H x W x D, mm); (H x W x D, inch): 86 x 165 x 260; 3.4 x 6.5 x 10.2 Accessories: Remote On-off: Yes Automatic Transfer Switch: Filax Standards: Safety: EN-IEC 60335-1 / EN-IEC 62109-1 / UL 458 (3) EMC: EN 55014-1 / EN 55014-2 / IEC 61000-6-1 / IEC 61000-6-2 / IEC 61000-6-3 Automotive Directive ECE R10-4: 1) Nonlinear load, crest factor 3:1; 2) Protection key: a) output short circuit b) overload c) battery voltage too high d) battery voltage too low e) temperature too high f) DC ripple too high Please contact your dealer for any returns, repairs or support issues related to this product.

3 Blade aluminum propeller for Honda 75-130 horsepower engines and Nissan/Tohatsu 60-90 horsepower engines. Both with 15 tooth spline and thru hub exhaust. 4-1/4" gearcase.