Simer 2810E-02 Shallow Well Jet Pump, 3/4HP Simer Shallow Well Jet Pump, Cast Iron Construction, 3/4HP 115/230 Volt Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, Best for Shallow Wells to 20 Feet, Maximum Lift 25 Feet, up to 14.4GPM, Adjustable Pressure Switch Set to 30psi On / 50psi Off

Simer 3107P Shallow Well Jet Pump, 3/4HP Simer Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 3/4HP 115/230V Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 10.3GPM at 40psi, Pressure Switch Set to 30psi On / 50psi Off, up to 25 Foot Water Depth

Flotec FP4822 Stainless Steel Shallow Well Jet Pump 3/4 HP Stainless steel shallow well jet pumps are heavy-duty, durable, corrosion resistant, high pressure and offer efficient non-stop operation for years. KEY FEATURES Superior performance at depths to water of 25' or less Heavy-duty, stainless steel pump housing for highest corrosion resistance Ready-to-install 230 volt motor - see manual for 115 volt conversion 1-1/4" NPT suction and 1" NPT discharge pipe sizes WARRANTY 1 year limited warranty  BODY CONSTRUCTION:  Stainless Steel HORSEPOWER:  3/4 MAXIMUM CAPACITY:  11 GPM FLOW at 10' LIFT and 40 PSI:  11 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  52 psi MAXIMUM INLET PRESSURE:   PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  NPT AMP DRAW (full load):  7.4 amps on 230v / 14.8 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v MAXIMUM WATER TEMPERATURE:  122°F (50 °C)

Flotec FP4022-10 Thermoplastic Shallow Well Jet Pump 3/4 HP This new revision of an "old hand" provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  3/4 MAXIMUM CAPACITY:  12 GPM FLOW at 10' LIFT and 40 PSI:  9.7 GPM MAX LIFT:  25' MAXIMUM PRESSURE:  78 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  6.1 amps on 230v / 12.2 amps on 115v VOLTAGE:  230v / 115v, 60 Hz RECOMMENDED BREAKER:  15 amp on 230v / 20 amp on 115v   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Sta-Rite PWP-01 Shallow Well Jet Pump 3/4HP Sta-Rite Shallow Well Jet Pump, Fiberglass Reinforced Thermoplastic Construction, 3/4HP 115/230V, 1-1/4”NPT Suction x 1”NPT Discharge Ports, up to 10.3GPM at 40psi, No Pressure Switch, up to 25 Foot Water Depth

Sta-Rite HMSE-1FL Multi-Stage Jet-Centrifugal Pump 1HP Sta-Rite- Multi-Stage Jet-Centrifugal Pump, Convertible, Cast Iron Construction, 1HP 115/230V Motor, 1-1/4" Suction Port, 1" Drive and Discharge Ports, 30/50PSI Pressure Switch, For Shallow or Deep Wells

Sta-Rite MSE-7 Vertical Multi-Stage Jet Pump 1HP Sta-Rite- Vertical Multi-Stage Jet Pump, Convertible, Cast Iron Construction, 1HP 115/230V Motor, 1-1/4" Suction and Drive Ports, 1" Discharge Port, 40/60psi Pressure Switch, For Shallow or Deep Wells

Flotec N76-46P Pump Body This is the durable plastic pump body, that is specially designed for use with Flotec shallow well jet pumps.   Replacement pump body N76-46P covers the pump impeller and directs water flow through the pump. This part replaces a worn or damaged body to restore proper pumping.   The Flotec, Simer and Sta-Rite pumps have interchangeable parts. If the part number is the same, it will work in any of the Flotec, Simer and Sta-Rite pumps.

STA-RITE A100DLL 3/4HP JET MOTOR

Simer 2805E-02 Shallow Well Jet Pump, 1/2HP Simer Shallow Well Jet Pump, Cast Iron Construction, 1/2HP 115/230Volt Motor, 1-1/4”NPT Suction x 1”NPT Discharge Ports, Best for Shallow Wells to 20 Feet, Maximum Lift 25 Feet, up to 8.5GPM, Adjustable Pressure Switch Set to 30psi On / 50psi

Goulds J5S 1/2Hp Shallow Well Jet Pump Goulds Jet Pump Shallow Well Only Cast Iron J+ Series, 1 1/4” x 1”FNPT Ports, 1/2HP 115V, Carbon/Ceramic/Buna Seal

Flotec FP4012-10 Thermoplastic Shallow Well Jet Pump 1/2 HP This new revision provides good pressure pumping from wells where the depth-to-water is 25' or less. KEY FEATURES Perfect for shallow wells (depth-to-water less than 25') Thermoplastic construction for higher corrosion resistance 1-1/4" Suction / 1" Discharge Comes with pre-wired 30/50 pressure switch WARRANTY 1 year limited warranty BODY CONSTRUCTION:  Thermoplastic HORSEPOWER:  1/2 MAXIMUM CAPACITY:  8 GPM FLOW at 10' LIFT and 40 PSI:  6.4 GPM MAX LIFT:  25' MAX PRESSURE:  77 psi PRESSURE SWITCH SETTING:  30/50 SUCTION PIPE SIZE:  1-1/4" NPT DISCHARGE PIPE SIZE:  1" NPT AMP DRAW (full load):  9.4 amps VOLTAGE:  115v/230v, 60 Hz (factory preset to 115v) RECOMMENDED BREAKER:  15 amp   MAXIMUM WATER TEMPERATURE:  140 °F (60 °C)

Sta-Rite JHB-61HL Centrifugal Pump High Head 1/3HP Sta-Rite- Centrifugal Pump, High Head, Cast Iron Construction, 1/3HP 115V Motor, 1-1/4" Suction and 1" Discharge Ports, up to 30GPM, up to 82 Feet of Head, Maximum Lift is 25 Feet

Sta-Rite JHC-61HL Centrifugal Pump High Head 1/2HP Sta-Rite- Centrifugal Pump, High Head, Cast Iron Construction, 1/2HP 115/230V Motor, 1-1/4" Suction and 1" Discharge Ports, up to 40GPM, up to 82 Feet of Head, Maximum Lift is 25 Feet

Sta-Rite JHE-63HL Centrifugal Pump High Head 1HP Sta-Rite- Centrifugal Pump, High Head, Cast Iron Construction, 1HP 115/230V Motor, 1-1/4" Suction and 1" Discharge Ports, up to 61GPM, up to 112 Feet of Head, Maximum Lift is 25 Feet