3/8" x 50' Boxed Barrier Lined B1-15 EPA Compliant Outboard Fuel Line Hose - Gray This hose is built with the best fuel and age-resistant formulations and a unique "Barrier Liner" on the inside surface of the tube, so the fuel is not in direct contact with rubber. This greatly reduces fuel permeation and prevents ethanol degradation of the rubber tube, which can cause small pieces of rubber to reach and damage the engine. That is particularly important considering the prospect of higher ethanol blends (E-15) available at gas stations next year.  Features:  Provides extraordinary resistance to fuel permeation, aging, heat, cold, and ozone   Also, provides excellent rope-like bend-ability and fitting retention For both gasoline (including ethanol blends up to E85) and diesel (including bio diesel blends up to 100%) EPA Certified and CARB Executive Order for low permeation Type B1-15 NMMA Type Accepted & CE certified Application: Marine Fuel Hose for distribution, return, vent and transfer For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Fluoroplastic Internal Barrier Cover: Gray CPE Rubber Reinforcement: 2-Spiral Polyester Plies  Temperature Range: -20°F to 212°F (-28ºC to 100ºC) Length: 50’ (15m) Boxed Specifications: Inner Diameter: (inch) 3/8" / (mm) 9.50 Outer Diameter: (inch) 0.588 / (mm) 14.9 Burst Pressure: (psi) 175 / (mpa) 1.21 Working Pressure: (psi) 35 / (mpa) 0.24 Bend Radius: (inch) 4" / (mm) 101.6 Weight: (lb/100 ft.) 10.5 / (kg/m) 0.156 Permeation Rate (Standard is (15g/m^2/24hrs (CE10)): 5.0 *The #305 series exceeds ABYC H-24, SAE J1527, ISO 8469 B1, USCG Type B1-15

5/16" x 50' Boxed Barrier Lined B1-15 EPA Compliant Outboard Fuel Line Hose - Gray This hose is built with the best fuel and age-resistant formulations and a unique "Barrier Liner" on the inside surface of the tube, so fuel is not in direct contact with rubber. This greatly reduces fuel permeation and prevents ethanol degradation of the rubber tube, which can cause small pieces of rubber to reach and damage the engine. That is particularly important considering the prospect of higher ethanol blends (E-15) available at gas stations next year.  Features:  Provides extraordinary resistance to fuel permeation, aging, heat, cold, and ozone   Also, provides excellent rope-like bend-ability and fitting retention For both gasoline (including ethanol blends up to E85) and diesel (including bio diesel blends up to 100%) EPA Certified and CARB Executive Order for low permeation Type B1-15 NMMA Type Accepted & CE certified Application: Marine Fuel Hose for distribution, return, vent and transfer For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Fluoroplastic Internal Barrier Cover: Gray CPE Rubber Reinforcement: 2-Spiral Polyester Plies  Temperature Range: -20°F to 212°F (-28ºC to 100ºC) Length: 50’ (15m) Boxed Specifications: Inner Diameter: (inch) 5/16" / (mm) 7.92 Outer Diameter: (inch) 0.500 / (mm) 12.7 Burst Pressure: (psi) 175 / (mpa) 1.21 Working Pressure: (psi) 35 / (mpa) 0.24 Bend Radius: (inch) 2.5" / (mm) 63.5 Weight: (lb/100 ft.) 7.8 / (kg/m) 0.116 Permeation Rate (Standard is (15g/m^2/24hrs (CE10)): 5.0 *The #305 series exceeds ABYC H-24, SAE J1527, ISO 8469 B1, USCG Type B1-15

3/8" x 50' Boxed Low Permeation Type A1-15 Fuel Line Hose - Black Trident Barrier Lined A1-15 Fuel Hose for both gasoline (including ethanol blends up to 85%) and diesel (including bio diesel blends up to B100). This hose is built with the best fuel, fire, and age-resistant formulation, and a unique "Barrier Liner" on the inside surface of the tube, so fuel is not in direct contact with rubber. Features:  Provides extraordinary resistance to fuel permeation, aging, and also to fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Application: Marine Fuel Hose (distribution, return, vent and transfer) For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC)  Length: 50 ft. (15 m) Boxed Specifications: Inner Diameter: (inch) 3/8" / (mm) 9.50 Outer Diameter: (inch) 0.681 / (mm) 17.3 Burst Pressure: (psi) 400 / (mpa) 2.76 Working Pressure: (psi) 100 / (mpa) 0.69 Bend Radius: (inch) 2" / (mm) 50.8 Weight: (lb/100 ft.) 15.6 / (kg/m) 0.233 Permeation Rate: <10 (Standard is 10g/m2/24 hrs (CE10) *The #365 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, USCG Type A1-15; CARB Executive Order RM-17-008 and EPA Certified low permeation Type A1-10

5/8" x 50' Boxed Type A2 Fuel & Vent Line Hose - Black Trident 5/8” A2 Fuel Hose for gasoline vent hose (including ethanol blends) and diesel (including bio diesel blends). This hose is built with the best fuel, fire and age resistant formulation. Features: Provides extraordinary resistance to aging, fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Application: Fuel Hose for vent and diesel distribution  For all marine fuels including gasoline, alcohol blends, diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC)  Length: 50 ft. (15 m) Boxed Specifications: Inner Diameter: (inch) 5/8" / (mm) 15.9 Outer Diameter: (inch) 0.960 / (mm) 24.4 Burst Pressure: (psi) 200 / (mpa) 1.38 Working Pressure: (psi) 50 / (mpa) 0.34 Bend Radius: (inch) 3" / (mm) 76.2 Weight: (lb/100 ft.) 25.84 / (kg/m) 11.72 *The #317 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, & USCG Type A2

5/8" x 50' Boxed Reinforced PVC (FDA) Hot Water Feed Line Hose - Drinking Water Safe - Translucent Red Trident 166 Series Red - polyester reinforced PVC hose for "Hot Water" feed lines. The FDA-grade tube is non-toxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures of up to 149ºF (65ºC) and can handle pressures to a maximum of 250 psi (varies based on i.d size).  Features:  The Red cover allows for easy identification of "Hot Water" lines on your boat Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility This hose is safe for use with drinking water Application: Perfect for hot, pressurized applications, hot water feed, drains, and vent lines Construction: Tube & Cover: Clear FDA tube  Color: Red Transparent  Reinforcement: Polyester Temperature Range: -18°F to 149°F (-28°C to 65°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 5/8" / (mm) 15.9 Outer Diameter: (inch) .866 / (mm) 22.5 Working Pressure: (PSI Vac In./Hg) 230 / (bar) 16 Bend Radius: (inch) 1.26" / (mm) 32 *Burst Pressure is 4 x Working Pressure

5/8" x 50' Boxed Reinforced PVC (FDA) Cold Water Feed Line Hose - Drinking Water Safe - Translucent Blue Trident 165 Series Blue - polyester reinforced PVC hose for "Cold Water" feed lines. The FDA-grade tube is non-toxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures as low as -18.4ºF (- 28ºC) and can handle pressures up to 250 psi (varies based on I.D size). Features:  The Blue cover allows for easy identification of "Cold Water" lines on your boat   Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility This hose is safe for use with drinking water Application: Perfect for cold pressurized applications, water feed, drains, and vent lines Construction: Tube & Cover: Clear FDA tube  Color: Blue Transparent  Reinforcement: Polyester Temperature Range: -18°F to 149°F (-28°C to 65°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 5/8" / (mm) 15.9 Outer Diameter: (inch) .866 / (mm) 22.5 Working Pressure: (PSI Vac In./Hg) 230 / (bar) 16 Bend Radius: (inch) 1.26" / (mm) 32 *Burst Pressure is 4 x Working Pressure

3/4" x 50' Boxed Reinforced PVC (FDA) Cold Water Feed Line Hose - Drinking Water Safe - Translucent Blue Trident 165 Series Blue - polyester reinforced PVC hose for "Cold Water" feed lines. The FDA-grade tube is non-toxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures as low as -18.4ºF (- 28ºC) and can handle pressures up to 250 psi (varies based on i.d size). Features:  The Blue cover allows for easy identification of "Cold Water" lines on your boat   Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility This hose is safe for use with drinking water Application: Perfect for cold pressurized applications, water feed, drains, and vent lines Construction: Tube & Cover: Clear FDA tube  Color: Blue Transparent  Reinforcement: Polyester Temperature Range: -18°F to 149°F (-28°C to 65°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 3/4" / (mm) 19 Outer Diameter: (inch) 1 / (mm) 25.4 Working Pressure: (PSI Vac In./Hg) 220 / (bar) 15 Bend Radius: (inch) 1.5" / (mm) 38 *Burst Pressure is 4 x Working Pressure

3/4" x 50' Boxed Reinforced PVC (FDA) Hot Water Feed Line Hose - Drinking Water Safe - Translucent Red Trident 166 Series Red - polyester reinforced PVC hose for "Hot Water" feed lines. The FDA-grade tube is nontoxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures of up to 149ºF (65ºC) and can handle pressures to a maximum of 250 psi (varies based on i.d size).  Features:  The Red cover allows for easy identification of "Hot Water" lines on your boat Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility This hose is safe for use with drinking water Application: Perfect for hot, pressurized applications, hot water feed, drains, and vent lines Construction: Tube & Cover: Clear FDA tube  Color: Red Transparent  Reinforcement: Polyester Temperature Range: -18°F to 149°F (-28°C to 65°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 3/4" / (mm) 19 Outer Diameter: (inch) 1 / (mm) 25.4 Working Pressure: (PSI Vac In./Hg) 220 / (bar) 15 Bend Radius: (inch) 1.5" / (mm) 38 *Burst Pressure is 4 x Working Pressure

 Outboard Fuel Line Issues   We could not start our outboard engine.  WHAT'S WRONG??    Our outboard engine usually always starts on the first pull and it is not flooded.   Trying to pump fuel through the squeeze bulb was a waste of time as fuel would not fill the bulb.  Take the line off the engine and put a screw driver in the end and sometimes it would pump fuel and sometimes it would not.  So you have to figure it is an issue with the hose or the bulb.  All fittings were factory tight and when the hose was submerged in water no air bubbles when squeezing the bulb.  Let's just replace the hose. We got lucky and got the dinghy started.  Off to the local chandlery we go, it was about a mile walk from the dock.  We were towed back to the boat because again we could not get the outboard started. This is our second fuel hose on a two year old engine.  Anyway I removed the fittings without a lot of work and reinstalled them on the new hose with new clamps.  The outboard is now starting on the first pull again.   About three weeks have gone by, we are now having starting issues again.  Now what? I pull the spark plugs out and the engine is not flooded.  That leaves a fuel issue again. I start playing with the fuel line again, it can not be this, I'm saying to myself.  I pull off the engine side of the fuel line from the bulb and nothing seems wrong.  Put that back together and take the tank end of the hose off the bulb.  There's an issue, I can't blow through it.   So I pull off the tank fitting, there it is, about a ½” in you can see something blocking the hose.  So I cut off about 3 inches of that end, I still could not blow through it. Cut off another 3 inches and found that same looking blockage twisted up in the hose.  What is this junk, this $50.00 fuel hose is garbage.  This time I have a new idea, can I pull this blockage out?  I was able to get hold of enough of that stuff to pull it all out of the hose.  It's a plastic liner and was twisted in several spots.  I ran some fuel through the hose without the liner, now to get rid of the glue that was used to keep the liner in place and then the engine ran fine.   Hose three, that's what I said hose number three.  This has to be a fluke so I bought another new hose and will change it out the next time I have an issue.  Well later is here and guess what.  The outer hose on this new replacement has shrunk some and the thin plastic liner is sticking out both ends of the new hose.  That hose was almost $65.00 as we were again in another country.   I have since replaced the Outboard Fuel Hose with Automotive Fuel Hose and put a plastic wire loom over it to protect it from the UV rays.  I'm just hoping the squeeze bulb I reused does not have a liner in it.  So far so Good two months later, our outboard starts on the first pull.       Closeouts     Rebates    Remanufactured    Specials  

5/16" x 50' Boxed Low Permeation Type A1-15 Fuel Line Hose - Black Trident Barrier Lined A1-15 Fuel Hose for both gasoline (including ethanol blends up to 85%) and diesel (including bio diesel blends up to B100). This hose is built with the best fuel, fire, and age-resistant formulation and a unique "Barrier Liner" on the inside surface of the tube, so fuel is not in direct contact with rubber. Features:  Provides extraordinary resistance to fuel permeation, aging, and also to fire, heat, cold, and the ozone  Also provides excellent bend-ability NMMA Type Accepted & CE certified Application: Marine Fuel Hose (distribution, return, vent and transfer) For all marine fuels including gasoline, alcohol blends (CE-10), diesel and bio-diesel Construction: Tube: Nylon Internal Barrier, NBR  Cover: NBR/PVC Blend  Reinforcement: Polyester 2 spiral  Temperature Range: -20°F to 212°F (-28ºC to 100ºC)  Length: 50 ft. (15 m) Boxed Specifications: Inner Diameter: (inch) 5/16" / (mm) 7.92 Outer Diameter: (inch) 0.611 / (mm) 15.5 Burst Pressure: (psi) 400 / (mpa) 2.76 Working Pressure: (psi) 100 / (mpa) 0.69 Bend Radius: (inch) 1.75" / (mm) 44.5 Weight: (lb/100 ft.) 13.3 / (kg/m) 0.198 Permeation Rate: <10 (Standard is 10g/m2/24 hrs (CE10) *The #365 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, USCG Type A1-15; CARB Executive Order RM-17-008 and EPA Certified low permeation Type A1-10

1/2" x 50' Boxed Reinforced PVC (FDA) Cold Water Feed Line Hose - Drinking Water Safe - Translucent Blue Trident 165 Series Blue - polyester reinforced PVC hose for "Cold Water" feed lines. The FDA-grade tube is non-toxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures as low as -18.4ºF (- 28ºC) and can handle pressures up to 250 psi (varies based on i.d size). Features:  The Blue cover allows for easy identification of "Cold Water" lines on your boat   Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility This hose is safe for use with drinking water Application: Perfect for cold pressurized applications, water feed, drains, and vent lines Construction: Tube & Cover: Clear FDA tube  Color: Blue Transparent  Reinforcement: Polyester Temperature Range: -18°F to 149°F (-28°C to 65°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 1/2" / (mm) 12.7 Outer Diameter: (inch) .777 / (mm) 19.6 Working Pressure: (PSI Vac In./Hg) 250 / (bar) 17 Bend Radius: (inch) 0.98" / (mm) 25 *Burst Pressure is 4 x Working Pressure

1/2" x 50' Boxed Reinforced PVC (FDA) Hot Water Feed Line Hose - Drinking Water Safe - Translucent Red Trident 166 Series Red - polyester reinforced PVC hose for "Hot Water" feed lines. The FDA-grade tube is non-toxic, odorless, and tasteless. Suitable for use in harsh operating conditions with temperatures of up to 149ºF (65ºC) and can handle pressures to a maximum of 250 psi (varies based on i.d size).  Features:  The Red cover allows for easy identification of "Hot Water" lines on your boat Made of 3-ply polyester for excellent abrasion resistance and sustained flexibility This hose is safe for use with drinking water Application: Perfect for hot, pressurized applications, hot water feed, drains, and vent lines Construction: Tube & Cover: Clear FDA tube  Color: Red Transparent  Reinforcement: Polyester Temperature Range: -18°F to 149°F (-28°C to 65°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 1/2" / (mm) 12.7 Outer Diameter: (inch) .777 / (mm) 19.6 Working Pressure: (PSI Vac In./Hg) 250 / (bar) 17 Bend Radius: (inch) 0.98" / (mm) 25 *Burst Pressure is 4 x Working Pressure

3/4" x 50' Heavy Duty PVC Bilge & Livewell Hose (FDA) - Clear with Black Helix Trident Smooth extra heavy wall vinyl (FDA) well hose. All clear (see thru) with black helix. Excellent durability, flexibility & bend radius for XHD bilge, live well, drain, scupper lines, etc. No cuffs are required.  Features: Flexible, but the 147 series is less flexible than the 149 series of hoses Application: Bilge and live well hose Specifications: Tube & Cover: Clear vinyl reinforced with black helix  Color: Clear with black helix Reinforcement: PVC Helix Temperature Range: 10°F-120°F (-12°C-49°C)  Boxed: 50ft. / (15.24m) Inner Diameter: (inch) 3/4" / (mm) 19 Outer Diameter: (inch) 0.968" / (mm) 24.6 Working Pressure: (Psi Vac In./Hg) 28 Weight: (Lb./ 50 ft.) 11 / (Kg/m) 0.33 Bend Radius: (inch) 2.25" / (mm) 57.2 *Burst Pressure is 4 x Working Pressure

3/4" x 50' VAC XHD Bilge & Live Well Hose - Hard PVC Helix - Black Trident VAC XHD Bilge and Live Well Hose. Helical PVC reinforcement provides excellent flexibility and bend radius for live well and heavy-duty bilge applications. It has a smooth outer surface to allow for easy clamping. The excellent bend radius of this product gives you the flexibility of a rubber hose making installations a breeze. Features: 149 series of hoses is extra flexible  Application: Bilge and live well hose Specifications: Tube & Cover: Hard PVC helix Color: Black Reinforcement: PVC Helix Temperature Range: 10°F-120°F (-12°C-48°C)  Boxed: 50ft. / (15.2m) Inner Diameter: (inch) 3/4" / (mm) 19.1 Outer Diameter: (inch) .986" / (mm) 25 Working Pressure: (Psi Vac In./Hg) 28 / (Bar) 1.93 Weight: (Lb./ 50 ft.) 11 / (Kg/m) 4.99 Bend Radius: (inch) 3" / (mm) 76.2 *Burst Pressure is 4 x Working Pressure

3/4" x 50' Coil Flex Marine Wet Exhaust & Water Hose - Black Trident Flex wet exhaust hose for longer bent connections. In smaller I.D.’s for engine intake, critical water, drain, scupper bilge & sanitation uses. Resists heat, ozone, exhaust, panting, and collapse. Black High Temp EDPM Rubber 250°F (121°C) Max. Features:  Extra heavy tube and cover with wire helix between 2 ply reinforcement provides excellent flexibility and bend radius  Resists heat, ozone, exhaust, sani chemicals, panting and collapse Exceeds SAE J2006-R2, ABYC & NMMA P-1 exhaust standards, and Lloyd’s Registry Type Approved Application: Trident Flex wet exhaust hose for longer bent connections In smaller I.D.’s for engine intake, critical water, drain, scupper bilge & sanitation uses Construction: Tube & Cover: High temp EDPM rubber Color: Black with blue stripe Reinforcement: Multi-ply, high-tenacity polyester, steel helix Temperature Range: 250°F (121°C) Length: 50’ (15.24m) Specifications: Inner Diameter: (inch) 3/4" / (mm) 20 Outer Diameter: (inch) 1.15" / (mm) 29 Working Pressure: (Psi) 100 / (bar) 6.9 Bend Radius: (inch) 1" / (mm) 25 Weight: (Lb./50ft.) 23 / (Kg/m) 10.3 *Burst Pressure is 4 x Working Pressure