ADAF3 Modular Top Plate for FLIR M300 Series Thermal Cameras f/Mounts Ending in M1 or M2 Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.  Unique Design No longer the unwanted “swiss cheese” look with a Seaview modular top plate. These plates result in only 4 visible mounting screws to secure electronics. A anodized 1/4" thick aluminum plate is pre-drilled to fit most marine electronics. This aluminum plate is then encased in a UV stable glass filled ABS white plastic. Each top plate is dimpled to match the provided drill templates for easy and precise drilling for your specific marine electronics. Note: This only applies to the ADA-R1, ADA-S1 & ADA-S2 Top Plates King Starboard The ADA-R2, ADA-S3, ADA-S4 & ADA-F1 Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation.

Black Modular Plate for FLIR M300 Series Thermal Cameras for Mounts Ending in M1 or M2 Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.

Modular Plate to Fit Searchlights & Thermal Cameras on Seaview Mounts Ending in M1 or M2 The Seaview ADABLANK is a universal modular top plate for mounting a searchlight or thermal camera for Seaview Modular Mounts ending in M1 or M2. King Starboard Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean-looking installation.

ADAF2 Black Modular Top Plate for FLIR M100 or M200 Series Cameras for Use with Mounts Ending in M1 or M2 This Seaview top plate is for FLIR M100 or M200 thermal cameras. This one-piece design gives the top plate a nice clean look and is made from King Starboard.

Modular Plate to Fit Searchlights & Thermal Cameras on Seaview Mounts Ending in M1 or M2 - Black The Seaview ADABLANKBLK is a universal modular top plate for mounting a searchlight or thermal camera for Seaview Modular Mounts ending in M1 or M2. King Starboard Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The result is a clean-looking installation.

Camera Plate 3 Fits FLIR M300 Series Thermal Cameras for Dual Mount Systems The modular Dual Power Tower has been designed to allow your open array. radar, satdome and camera to be mounted together in one single space saving modular installation. Specifically for Camera plate 2 (FLIR M300 Thermal Imaging Cameras for Dual Mount Systems)

Mast Mount for FLIR M300 Series Fits Mast with 2-5/8" or Larger Achieve an unobstructed view for your FLIR or Raymarine thermal camera by mounting it on your mast. Made from marine grade aluminum. We now Chem-Film (same process used by Boeing) each high grade aluminum part prior to our standard 3 part epoxy prime and powder coat to ensure the best possible finish and corrosion resistance. Heavy Duty Six rivets per foot are used to hold the heavy duty mounting feet to the mast. Solid under-body construction not only greatly improves strength but also hides cables.

2" Diameter Compact Light Bar f/Thermal Cameras, Spotlights & Nav Light To Clear Closed Dome Radars *Must Pick an LTB TOP A compact 2” diameter light bar designed to fit Seaview modular mounts that will elevate most searchlights, thermal cameras with the universal plate, and a nav light above closed dome radars. This will clear 18-24" diameter closed dome radars with the exception of Raymarine RD424.  Works with Mounts ending in M1 or M2. * Will work for all FLIR models, WITH THE EXCEPTION OF THE FLIR M300C, M332, M364, M364C ** Will clear 18"-24" closed dome radars, WITH THE EXCEPTION OF THE RAYMARINE RD424

Electrically Actuated Hinge 24V Fits Seaview Mounts Ending in M1 & M2 The Seaview SVEHB1 electrically actuated hinge will fit all Seaview mounts with 7"x7" and 10"x10" mounting base plates. Some electronics can also be mounted directly to the hinge plates when needed (contact Seaview to direct mount electronics). Professionally designed to raise and lower marine electronics with the push of a button. This single electrically actuated hinge will accommodate single small Seaview mounts up to large dual mounts fully loaded with marine electronics. This hinge is 5-9/16" tall x 13" wide x 20-1/2" long. This will hinge approximately 93 degrees leaving the hinge plate vertical off the mounting surface about 11-7/16". This Seaview hinge is marine grade aluminum expertly fabricated for consistently superior welds. The actuator used is 24V however, 12V is an option with a conversion kit. The 24V actuator has a current draw of 10.4 amps on startup and when it is fully loaded with 2248 pound-force. The hinge has a very durable finish unlike anything else in the industry. This is first chem treated (for corrosion resistance), then an epoxy polyester primer coat is applied and finished with a polyester powder coat for a superior gloss white finish. There are two waterproof cable glands inside the hinge for water proof cable routing. This also has a removable lid to conveniently service the inside of the hinge if needed. This actuated hinge has been used for many applications. Some examples, but not limited to are: Princess 66, Navetta 48, Sunseeker 52 & 66, Absolute 58, Sabre 45, Jupiter 27 and HCB Yacht 65CC. Features: Electrically Actuated Hinge  Volt: 24V  Fits Seaview Mounts ending M1 and M2

  FLIR is excited to announce the launch of the FLIR M-Series Thermal Promotion! For a limited time, save $1,000 on select M-Series stabilized thermal cameras.   Navigate at night like a pro with the enhanced situational awareness and peace of mind a FLIR M-Series camera brings aboard.  Hurry in to your authorized FLIR dealer and add a FLIR M-Series camera to your boat. The M-Series $1,000 rebate runs through July 7th, 2019 and is valid on the following M-Series models: M-324CS, M-625S, M-625CS and M-617CS.  *Offer valid now until July 7th, 2019     Specials    Closeouts   Remanufactured    Rebates  

5.5" Thermal Camera Mount for FLIR M300 Series Cameras Seaview 5" and 12" tall aft leaning mounts for thermal cameras and searchlights. Powder-coated brilliant white gives it a nice clean look and yet is very durable. Specifically designed for installations where space is very limited. The base for this mount is 7″ x 7″. Cable Management  A hollow oval mast section provides plenty of room for cable management. Space Saving Design The small 7"x 7" base footprint makes this a great solution to an installation where space is an issue.

Modular Top Plate for Flir M or Ray T Series Thermal Cameras Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. King Starboard Made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation. 

Starlink Modular Top Plate with Starlink Stainless Steel 1"-14 Threaded Adapter & Stainless Steel Base Starlink quick-release top plate for Seaview "M1" and "M2" style mounts. Features: 316L stainless steel Starlink adapter with a 1"-14 threaded fixed base on ¼” aluminum plate The top of the adapter is machined to fit the Starlink antenna post The adapter with the fixed base and modular plate is 4 1/4” tall The ¼” aluminum plate is powder-coated white and can accommodate a Seaview light bar

Starlink Maritime Top Plate for Seaview M1 & M2 Style Modular Mounts Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Features: Starlink Wedge Base hole pattern pre-dimpled in this modular top plate Water-tight gasket in the center of the plate to pass the Starlink cable The 1” thick starboard plate can accommodate a Seaview light bar

Starlink Maritime Top Plate for Seaview M1 Style Modular Mounts Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Features:  Water-tight gasket in the center of the plate to pass the Starlink cable Predrilled and all hardware needed to mount the Starlink is included *Not light bar compatible