Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Adhesive Lined Heat Shrink Tubing (ALT) - 1/8" x 6" - 10-Pack - Black Package of 10 Black 6"(15.2cm) long sections with a 1/8"(3.2mm) diameter that shrinks to 1/32"(0.8 mm) Wire Range: <18 AWG Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257°F / 125°C Operating temperature range of -40°C to 110°C UL 224 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

Coolant Temperature Sensor - 40°C to 120°C - 1/8 - 27NPTF Features: Measurement Range - 40°C - 120°C Category - Temperature Sensors Signal Analogue - 287.4 - 22.7 Ohm Operating Voltage - 6 - 24 V Temperature medium - Coolant - Water - Air - Engine oil - Transmission oil - Fuel Communication - Analog Signal Output - 287.4 - 22.7 Ohm Sensor Signal - Common Ground Sensor Connector - AMP Male T-Model 6.3 X 0.8 mm Thread1/8" - 27 NPTF Male Warning Contact - None Connector Type - AMP Blade T-Model 6.3 X 0.8 mm *Sold as an Individual This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

1-1/8" x 50' VAC XHD Bilge & Live Well Hose - Hard PVC Helix - Black Trident VAC XHD Bilge and Live Well Hose. Helical PVC reinforcement provides excellent flexibility and bend radius for live well and heavy-duty bilge applications. It has a smooth outer surface to allow for easy clamping. The excellent bend radius of this product gives you the flexibility of a rubber hose making installations a breeze. Features: 149 series of hoses is extra flexible  Application: Bilge and live well hose Specifications: Tube & Cover: Hard PVC helix Color: Black Reinforcement: PVC Helix Temperature Range: 10°F-120°F (-12°C-48°C)  Boxed: 50ft. / (15.2m) Inner Diameter: (inch) 1-1/8" / (mm) 28.6 Outer Diameter: (inch) 1.433" / (mm) 36.4 Working Pressure: (Psi Vac In./Hg) 28 / (Bar) 1.93 Weight: (Lb./ 50 ft.) 15 / (Kg/m) 6.80  Bend Radius: (inch) 3" / (mm) 76.2 *Burst Pressure is 4 x Working Pressure

1-1/8" x 50' Heavy Duty PVC Bilge & Livewell Hose (FDA) - Clear with Black Helix Trident Smooth extra heavy wall vinyl (FDA) well hose. All clear (see thru) with black helix. Excellent durability, flexibility & bend radius for XHD bilge, live well, drain, scupper lines, etc. No cuffs are required.  Features: Flexible, but the 147 series is less flexible than the 149 series of hoses Application: Bilge and live well hose Specifications: Tube & Cover: Clear vinyl reinforced with black helix  Color: Clear with black helix Reinforcement: PVC Helix Temperature Range: 10°F-120°F (-12°C-49°C)  Boxed: 50ft. / (15.24m) Inner Diameter: (inch) 1-1/8" / (mm) 28.6 Outer Diameter: (inch) 1.39" / (mm) 35.4 Working Pressure: (Psi Vac In./Hg) 28 Weight: (Lb./ 50 ft.) 15 / (Kg/m) 0.45 Bend Radius: (inch) 3.5" / (mm) 8.9 *Burst Pressure is 4 x Working Pressure

Single layer corrugated polyethylene hose. Resistant to mild chemicals and salt water. Clamping cuff every 1 foot. Primarily used for bilge pump discharge. Do not attach to thru hull fitting below the water line.

On-Board Precision Charger MK-106 PCL 1 Bank x 6 AMP LI Optimized Charger Longer run times. Shorter charge times. That's the precision difference that keeps anglers on the water longer and puts more fish in the boat. Now, the next generation of this legendary line of chargers has been optimized for 12-volt lithium (LiFePO4) batteries. Precision chargers feature battery-type selection by the bank, which now includes charge curves specially formulated for the high demands of lithium batteries, and can even wake these battery types from standby. Features: Battery Type Selection: Each charging bank can be selected to your specific battery type (Lithium (LiFePO4) AGM or flooded lead acid) to guarantee a safe, protected charge Automatic Temperature Compensation: Precision chargers sense and adjust to ambient temperature fluctuations to ensure a fast, accurate charge Low-Line Voltage Compensation: When outlets don't put out the 120 volts they are supposed to, Precision Chargers compensate to deliver a fast, consistent charge no matter what Battery Equalization: Cleans and protects your battery (flooded lead-acid only) every time you plugin. Also activates a more rigorous, complete cleaning at the push of a button Digital Control: Microprocessor-based design delivers a faster, more precise charge every time. Precision chargers can even wake dead 12-volt lithium (LiFePO4) batteries from standby automatically. LED Indicator Lights: Inform of charge stage, maintenance mode status, error notifications, and full charge Automatic Multi-Stage Charging: Controls the voltage and current your battery gets throughout the charging cycle, ensuring a fast, safe and precise charge Waterproof Construction: All on-board chargers are built to be waterproof, shock-resistant and vibration-resistant 3-Year Warranty: All battery chargers come with a full 3-year replacement warranty Specifications: Product Dimensions: 9.88 in x 4 in x 3.5 in Product Weight: 4.4 lb Charger Style: On-Board Output per Bank: 6 amps Wattage: 90W Charge Time: 10-12 hours Power Source: On-Shore AC Battery Type: 12v Lithium LiFePO4, 12v AGM, 12v Flooded Lead Acid 12v Lithium-Ion (LiFePO4) Optimized: Yes Waterproof: Yes Digital Control: Yes Automatic Temperature Compensation: Yes Battery Equalization: Yes Battery Type Selection: Yes LED Display: Yes Saltwater Compatible: Yes Battery Connection: Ring Terminal Warranty: Three-Year Warranty

R1 8" x 6.5" Vamp Spin Tower Speakers - Black - 160W RMS & 320W Peak Power Roswell’s patented vamp spin technology is supercharged with the R1 audio series, giving users 360 degrees of premium sound-sending freedom. This versatile combination pairs our R1 8" and R1 6.5" together to keep the party cranking from the front to the back, on the sandbar, and beyond. Features: Klippel® tested and certified to guarantee acoustic performance R1 8” & R1 6.5” component-style speakers    Coaxially mounted 1" silk dome tweeter Patented speaker spin technology allows the 6.5" speaker to spin 180 degrees   Concealed integrated 12 dB/oct crossover network Integrated RGB LED backlight the cone to create your desired visual atmosphere   Machined billet Roswell 360º 3" Universal Clamp with 1.90", 2.375, and 3" adapters Deutsch wiring harness included for water-tight connection Specifications: Color: Black Continuous Power (RMS): 160 Watts Peak Power (RMS): 320 Watts Sensitivity: 90 dB @ 1W/1M Frequency Response (+ / - 3 dB): 50Hz - 20kHz Impedance Ω: 2Ω Dimensions: Diameter: Spin Speaker: 6.5 in. I 16.51 cm / Mounted Speaker: 8 in | 20.32 Total Width: 19.30 in. I 49.0 cm  Total Depth: 13.575 in. 34.5 cm Hanging Distance (from center to lowest point): 12.26 in. I 31.93 cm *Sold as a Pair

Stainless Steel Locker Vent - 2-3/8" x 6-3/4"  Locker Vents are designed to promote air circulation in interior areas and prevent mold, mildew, and unpleasant odors. Easy to install with six #8 RH fasteners (not included). Corrosion resistant stamped 304 stainless steel construction. Vent area 2.56 in2.

Zinc U-Bolt 7/16"-14 X 3-1/8" X 4" with Washers & Nuts - Square Zinc-plated u-bolt for mounting brackets & accessories to trailer frames. Features: Square bend Grade 5 7/16"-14 diameter/thread 3-1/8" W x 4" L *Comes packaged with nuts and washers.

Zinc U-Bolt 7/16"-14 X 3-1/8" X 3" with Washers & Nuts - Square Zinc-plated u-bolt for mounting brackets & accessories to trailer frames. Features: Square bend Grade 5 7/16"-14 diameter/thread 3-1/8" W x 3" L *Comes packaged with nuts and washers.

Teak Louvered Insert Height:16" Width:9-1/8" Depth:3/4" Cut Out Height:15" Width:8-1/8" Measurements for the inserts, door, and drawer/door fronts are from outside edge to outside edge. All items have a 1/2" rabbet and use a cutout size one inch less than the listed dimension