Sikasil®-N Plus Clear 10oz with Nozzle Sikasil®-N Plus US is a general-purpose, one-component, non-sag, elastomeric, 100% RTV neutral cure silicone sealant. Meets the requirements of ASTM C-920, Type S, Grade NS, Class 25, Use NT, T, M, G, A, O; TT-S-00230C, Type II, Class A; TT-S-001543A, Class A; CAN/CGSB-19.13-M87, AAMA 802.3 Type II, AAMA 803.3, AAMA 805.2, AAMA 808.3 and California Air Resources Board 2003 requirements for Volatile Organic Compound content.  Features: Extremely long service life Excellent flexibility for dynamic joint movement Bonds to most substrates without priming Usage: Window and door fabrication Conventional glazing Back bedding and cap, toe and heel beads Perimeter sealing of windows, doors, and skylights Expansion and control joints HVAC, White goods assembly Kitchen and bath countertops/solid surfaces, Sanitary Seals Marine cabins Truck/trailer/auto/RV Typical Substrates:  Glass, aluminum, tile, fiberglass, plastic, ceramic, masonry, concrete, brick and wood Advantages: Extremely long service life Excellent flexibility for dynamic joint movement Bonds to most substrates without priming Ready to use, no mixing required AAMA Certified component for window backbedding/glazing All season ease of application Fungicide additive for mildew resistance

Sikasil®-N Plus White 10oz with Nozzle Sikasil®-N Plus US is a general-purpose, one-component, non-sag, elastomeric, 100% RTV neutral cure silicone sealant. Meets the requirements of ASTM C-920, Type S, Grade NS, Class 25, Use NT, T, M, G, A, O; TT-S-00230C, Type II, Class A; TT-S-001543A, Class A; CAN/CGSB-19.13-M87, AAMA 802.3 Type II, AAMA 803.3, AAMA 805.2, AAMA 808.3 and California Air Resources Board 2003 requirements for Volatile Organic Compound content.  Features: Extremely long service life Excellent flexibility for dynamic joint movement Bonds to most substrates without priming Usage: Window and door fabrication Conventional glazing Back bedding and cap, toe and heel beads Perimeter sealing of windows, doors, and skylights Expansion and control joints HVAC, White goods assembly Kitchen and bath countertops/solid surfaces, Sanitary Seals Marine cabins Truck/trailer/auto/RV Typical Substrates:  Glass, aluminum, tile, fiberglass, plastic, ceramic, masonry, concrete, brick and wood Advantages: Extremely long service life Excellent flexibility for dynamic joint movement Bonds to most substrates without priming Ready to use, no mixing required AAMA Certified component for window backbedding/glazing All season ease of application Fungicide additive for mildew resistance

Sikaflex® 291 LOT - White - 3oz Tube with Nozzle Sikaflex®-291 LOT is a 1-component, marine-grade polyurethane elastomeric adhesive, and sealant. It is a moisture-cured, non-sag system designed with a long open time for jobs that require more time. Features: Use above and below the waterline Resists saltwater Paintable and sandable Usage: General all-purpose, high strength marine sealant, which may be used for light-duty bonding with long open time capability for humid climates or jobs requiring more time that remains permanently elastic. Advantages: Use above and below the waterline Resists saltwater Paintable  and sandable Excellent bond   NSF approved for potable water USDA approved for incidental food contact

Sikaflex® 291 LOT - Black - 3oz Tube with Nozzle Sikaflex®-291 LOT is a 1-component, marine-grade polyurethane elastomeric adhesive, and sealant. It is a moisture-cured, non-sag system designed with a long open time for jobs that require more time. Features: Use above and below the waterline Resists saltwater Paintable and sandable Usage: General all-purpose, high strength marine sealant, which may be used for light-duty bonding with long open time capability for humid climates or jobs requiring more time that remains permanently elastic. Advantages: Use above and below the waterline Resists saltwater Paintable  and sandable Excellent bond   NSF approved for potable water USDA approved for incidental food contact

Sikaflex® 295 UV - White - 10oz Tube with Nozzle Exterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).   Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of Application Sikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.  Application: Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting Sikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

Sikaflex® 295 UV - Black - 10oz Tube with Nozzle Exterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).   Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of Application Sikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.  Application: Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting Sikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

Sikaflex® 292i - White - 10oz Tube with Nozzle Sikaflex®-292i is a non-sag 1-component polyurethane adhesive of thixotropic, paste-like consistency which cures on exposure to atmospheric moisture. It exhibits excellent adhesive properties and good mechanical strength. Sikaflex®-292i meets the low spread of flame requirements set out by the International Maritime Organisation (IMO).   Features: Good gap-filling properties Can be painted Bonds well to a wide variety of substrates Areas of Application: Sikaflex®-292i is suitable for structural joints in marine constructions which will be subjected to high dynamic stresses. It is suitable to bond metals, particularly aluminum (including anodized finishes), metal primers and paint coatings (2-component systems), or ceramic materials, plastics such as GRP (unsaturated polyester resin), ABS, etc. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-292i on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring adhesion and material compatibility.   Benefits: Good gap-filling properties Can be painted Bonds well to a wide variety of substrates Wheelmark approved Solvent-free and very low VOC Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application: Sikaflex®-292i can be processed between 10 °C and 40 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-292i can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin.

Sikasil® N PLUS - Translucent - 3oz Features: Bonds well to most substrates Fungicide additive for mildew resistance Excellent flexibility for dynamic joint movement Extremely long service life All season ease of application WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikasil® N PLUS - White - 3oz Features: Bonds well to most substrates Fungicide additive for mildew resistance Excellent flexibility for dynamic joint movement Extremely long service life All season ease of application WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

STRIKER™ Plus 4 US w/Dual-Beam Transducer 4” GPS Fishfinder with Industry-leading Sonar and Quickdraw Contours Mapping Software Includes dual-beam transducer with Garmin CHIRP traditional sonar for crystal-clear images and remarkable target separation Built-in Garmin Quickdraw™ Contours mapping software lets you create and store maps with 1’ contours for up to 2 million acres Built-in GPS lets you mark waypoints, create routes and view boat’s speed Bright, sunlight-readable 4.3” display and intuitive user interface Rugged design for every fishing environment The STRIKER Plus 4 fishfinder with a bright 4.3” display and built-in GPS features CHIRP sonar for crystal-clear images and Quickdraw Contours map drawing software, which stores up to 2 million acres of content with 1’ contours. The built-in GPS lets you mark and navigate to waypoints and shows your boat’s speed. Garmin Quickdraw Contours Nobody knows the waters you fish better than you and your fellow fishermen. While you are trolling the shorelines and the depths, Quickdraw Contours mapping software creates HD fishing maps of the places you’ve been. No special knowledge is required. STRIKER Plus 4 can now store up to 2 million acres of your Quickdraw Contours maps with 1’ contours. CHIRP Sonar Clarity The STRIKER Plus 4 fishfinder includes Garmin CHIRP technology for a higher level of clarity and detail that you have come to expect from Garmin. Crystal-clear sonar images provide remarkable target separation and resolution in shallow and deeper water. Bottom contours are more visible, even at higher speeds, and signal noise can be suppressed at greater depths for a timely interpretation of what’s below. GPS Fishfinder The built-in, high-sensitivity GPS finds and maintains your position anywhere you go on the water. The GPS allows you to mark waypoints for different locations. So, if the fish are biting in 1 spot, you can mark it, and return to it on your next trip. Mark docks, boat ramps and other locations on the lake, and create routes back to them for your next trip. GPS also allows STRIKER Plus 4 to show your speed on screen, so you can be sure you’re trolling at the right speed for the lure you’re using or in wake-controlled areas. Built for You The STRIKER Plus 4 fishfinder makes fishing a breeze, and it’s built to work in any environment. The bright, sunlight-readable display gives you a clear view of what is below your boat, even on the brightest days. And the larger screen gives you a better view of what is happening below the boat. The intuitive user interface makes it simple to navigate to whatever feature you need, so you are ready for anything on the water. In The Box STRIKER Plus 4 fishfinder Garmin dual beam transducer with 20' cable Power/data cable Tilt/swivel mount Hardware Documentation Connections Transducer Ports: 1 (4 Pin) WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

RAM STACK-N-STOW Bait Board w/18" Pipe, Post & Spline The RAP-395-PSP-18U consists of the RAM STACK-N-STOW Bait Board and 18" long pipe with spline post. The bait board includes a magnetic surface for bait knife, hooks, lures or any ferrous metal item, never again scramble to find your essential tools while on the water. With various extension pole options for post and spline you can get creative with your install. Integrated features for hanging tools, lures, clippers, mounting a GoPro camera, cup holders and much more, this bait board is a feature rich option for the savvy angler. With spline post, located on the bottom of the 18" long pipe, easily integrate it to your existing spline post base, or choose from an assortment of RAM compatible bases. With the 18" long pipe, quickly rotate the bait board away from the action. Tightening of the included knob will resecure the bait board. Features: Magnetic surface for tools Customized mounting options Accessorize with phone, camera, drink cup mounts Mounting options for boat and kayak High strength materials ensure product longevity Integrated features for hanging tools Easy removal and stowage Made in U.S.A. Lifetime warranty Bait Board Dimensions: Length: 10" Width: 13" Depth: 1.625" Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag.

RAM STACK-N-STOW Bait Board w/Combination Bulkhead Rail Adapter Kit The RAP-395-RMU consists of the RAM STACK-N-STOW Bait Board, 3" long spline post and bulkhead rail adapter kit. The bait board includes a magnetic surface for bait knife, hooks, lures or any ferrous metal item, never again scramble to find your essential tools while on the water. With various extension pole options for post and spline you can get creative with your install. Integrated features for hanging tools, lures, clippers, mounting a GoPro camera, cup holders and much more, this bait board is a feature rich option for the savvy angler. This mount joins two plates with the screws provided and turns the flate base into a rail base. The adapter is a U shape, so it can wrap around a tube mount and the clamp by joining to the flat base. The bait board will also accomodate pipes and extension poles with a diameter of 1". Features: Magnetic surface for tools Customized mounting options Accessorize with phone, camera, drink cup mounts Mounting options for boat and kayak High strength materials ensure product longevity Integrated features for hanging tools Easy removal and stowage Made in U.S.A. Lifetime warranty Bait Board Dimensions: Length: 10" Width: 13" Depth: 1.625" Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag.

RAM STACK-N-STOW Bait Board w/Combination Bulkhead/Flat Surface Base & Plunger The RAP-395-BMPU consists of the RAM STACK-N-STOW Bait Board, 3" long spline post and combination bulkhead/flat surface mounting base. The bait board includes a magnetic surface for bait knife, hooks, lures or any ferrous metal item, never again scramble to find your essential tools while on the water. With various extension pole options for post and spline you can get creative with your install. Integrated features for hanging tools, lures, clippers, mounting a GoPro camera, cup holders and much more, this bait board is a feature rich option for the savvy angler. The mounting base can be installed on a flat surface such as the deck or on a vertical surface. This mounting base features a locking feature which requires the release of a plunger to remove the rod holder. The bait board will also accomodate pipes and extension poles with a diameter of 1". Features: Magnetic surface for tools Customized mounting options Accessorize with phone, camera, drink cup mounts Mounting options for boat and kayak High strength materials ensure product longevity Integrated features for hanging tools Easy removal and stowage Made in U.S.A. Lifetime warranty Bait Board Dimensions: Length: 10" Width: 13" Depth: 1.625" Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag.

RAM STACK-N-STOW Topside Base w/1" Ball The RAP-395W-BBU consists of a 1" ball, connected to a round base, that contains female grooves and hardware that will allow mounting to all RAM STACK-N-STOW Bait Boards. Material: High Strength Composite Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

Aktivator-205 Clear 250ml Bottle Sika® Aktivator-205 is a solvent-based colorless clear adhesion promoter, which reacts with moisture and deposits active groups on the substrate. These groups act as a link between substrates and primers or sealants/adhesives. Sika® Aktivator-205 is designed for the treatment of bond faces prior to the application of Sikaflex® and Sikasil® adhesives and sealants.    Features: Enhanced adhesion on various substrates Short flash-off time Easy to use Transparent Areas of Application: Sika® Aktivator-205 is used to improve adhesion on non-porous substrates such as metals, plastics, ceramic screen prints, and painted surfaces. Seek manufacturer’s advice and perform tests on original substrates before using Sika® Aktivator-205 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.