Sikaflex® 295 UV - White - 10oz Tube with Nozzle Exterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).   Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of Application Sikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.  Application: Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting Sikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

Sikaflex® 295 UV - Black - 10oz Tube with Nozzle Exterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).   Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of Application Sikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.  Application: Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting Sikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

Sikaflex® 292i - White - 10oz Tube with Nozzle Sikaflex®-292i is a non-sag 1-component polyurethane adhesive of thixotropic, paste-like consistency which cures on exposure to atmospheric moisture. It exhibits excellent adhesive properties and good mechanical strength. Sikaflex®-292i meets the low spread of flame requirements set out by the International Maritime Organisation (IMO).   Features: Good gap-filling properties Can be painted Bonds well to a wide variety of substrates Areas of Application: Sikaflex®-292i is suitable for structural joints in marine constructions which will be subjected to high dynamic stresses. It is suitable to bond metals, particularly aluminum (including anodized finishes), metal primers and paint coatings (2-component systems), or ceramic materials, plastics such as GRP (unsaturated polyester resin), ABS, etc. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-292i on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring adhesion and material compatibility.   Benefits: Good gap-filling properties Can be painted Bonds well to a wide variety of substrates Wheelmark approved Solvent-free and very low VOC Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application: Sikaflex®-292i can be processed between 10 °C and 40 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-292i can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin.

Sikaflex® 295 UV - White - 3oz Tube Features: UV resistant – no cracking or chalking Salt water resistant Good gap filling properties Fast tack-free time Paintable and sandable Bonds and seals in one step Non-yellowing WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 291 LOT - White - 3oz Tube with Nozzle Sikaflex®-291 LOT is a 1-component, marine-grade polyurethane elastomeric adhesive, and sealant. It is a moisture-cured, non-sag system designed with a long open time for jobs that require more time. Features: Use above and below the waterline Resists saltwater Paintable and sandable Usage: General all-purpose, high strength marine sealant, which may be used for light-duty bonding with long open time capability for humid climates or jobs requiring more time that remains permanently elastic. Advantages: Use above and below the waterline Resists saltwater Paintable  and sandable Excellent bond   NSF approved for potable water USDA approved for incidental food contact

Sikaflex® 291 Fast Cure - White - 3oz Tube Sikaflex® 291 is a 1-component, marine grade polyurethane elastomeric adhesive and sealant. Used by many boat builders, its fast cure time makes it ideal for applications where speed is important. Sikaflex® 291 is manufactured in accordance with IOS 9001/14001 quality assurance system and the responsible care program. Features: General purpose polyurethane marine sealant Fast curing Above and below water applications Ideal for sealing thru hull and hardware applications Excellent adhesion to Gelcoat Resists saltwater WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 295 UV - Black - 3oz Tube Features: UV resistant – no cracking or chalking Salt water resistant Good gap filling properties Fast tack-free time Paintable and sandable Bonds and seals in one step Non-yellowing WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 291 LOT - Black - 3oz Tube with Nozzle Sikaflex®-291 LOT is a 1-component, marine-grade polyurethane elastomeric adhesive, and sealant. It is a moisture-cured, non-sag system designed with a long open time for jobs that require more time. Features: Use above and below the waterline Resists saltwater Paintable and sandable Usage: General all-purpose, high strength marine sealant, which may be used for light-duty bonding with long open time capability for humid climates or jobs requiring more time that remains permanently elastic. Advantages: Use above and below the waterline Resists saltwater Paintable  and sandable Excellent bond   NSF approved for potable water USDA approved for incidental food contact

Sikaflex® 291 Fast Cure - Black - 3oz Tube  Sikaflex® 291 is a 1-component, marine grade polyurethane elastomeric adhesive and sealant. Used by many boat builders, its fast cure time makes it ideal for applications where speed is important. Sikaflex® 291 is manufactured in accordance with IOS 9001/14001 quality assurance system and the responsible care program. Features: General purpose polyurethane marine sealant Fast curing Above and below water applications Ideal for sealing thru hull and hardware applications Excellent adhesion to Gelcoat Resists saltwater WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

BPO Cream Hardener White 1oz Tube Resin Required BPO (benzoyl peroxide) is a peroxide used for curing amine accelerated polyester resins and fillers. It leads to rapid hardening and de-molding, even at low temperatures.

BPO Cream Hardener White 4oz Tube Resin Required BPO (benzoyl peroxide) is a peroxide used for curing amine accelerated polyester resins and fillers. It leads to rapid hardening and de-molding, even at low temperatures.

Sikaflex®-715 - White - 300ml Cartridge Semi self-leveling roof membrane sealer. Sikaflex®-715 is a one-component silane terminated polymer (STP) sealant that cures on exposure to atmospheric humidity.  Its unique flow characteristic is designed for roof sealing applications.  Sikaflex®-715 has very good adhesion and UV resistance making it suitable for open joints.   Features: Primerless adhesion to the difficult substrate Semi self-leveling for roof sealing Very good dispensing characteristics Isocyanate free Low VOC content Very good UV resistance Usage: Sikaflex®-715 is suitable for sealing a wide variety of RV roofing components including, EPDM; metals such as anodized and bare aluminum; phosphate, chromate, and zinc-plated steel; metal primers; 2-part coatings; ceramics and plastics. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-715 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface Preparation: Surfaces must be clean, dry and free from grease, oil and dust. For repairs, removal of pre-exisiting products is crucial to avoid compatibility issues.  Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Adhesion and compatibility have to be verified by tests on original substrates. Application: Sikaflex®-715 can be processed between 5 °C and 40 °C (41 °F and 104 °F) but, changes in reactivity and application properties have to be considered. The optimum temperature for substrate and process material is between 15 °C and 25 °C (59 °F and 77 °F). Sikaflex®-715 can be processed with manual, pneumatic, or electric-driven piston guns as well as pump equipment. Removal: Uncured Sikaflex®-715 may be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically.  Hands and exposed skin have to be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting: Sikaflex®-715 is not suitable for overpainting. Specifications: Chemical base: Silane Terminated Polymer Color (CQP001-1): White, black Cure mechanism: Moisture-curing Density (uncured): 1.52 kg/l (12.7 lb/gal) Non-sag properties: Semi self-leveling Application temperature: 5-40 °C (41-104 °F) Skin time (CQP019-1): 30 minutes A Shore A hardness (CQP023-1 / ISO 48-4): 10 Tensile strength (ASTM D412): 0.6 MPa (85 psi) Elongation at break (ASTM D412): 500% Service temperature (CQP513-1): -50-90 °C (-58-94 °F)

Sikasil®-N Plus White 10oz with Nozzle Sikasil®-N Plus US is a general-purpose, one-component, non-sag, elastomeric, 100% RTV neutral cure silicone sealant. Meets the requirements of ASTM C-920, Type S, Grade NS, Class 25, Use NT, T, M, G, A, O; TT-S-00230C, Type II, Class A; TT-S-001543A, Class A; CAN/CGSB-19.13-M87, AAMA 802.3 Type II, AAMA 803.3, AAMA 805.2, AAMA 808.3 and California Air Resources Board 2003 requirements for Volatile Organic Compound content.  Features: Extremely long service life Excellent flexibility for dynamic joint movement Bonds to most substrates without priming Usage: Window and door fabrication Conventional glazing Back bedding and cap, toe and heel beads Perimeter sealing of windows, doors, and skylights Expansion and control joints HVAC, White goods assembly Kitchen and bath countertops/solid surfaces, Sanitary Seals Marine cabins Truck/trailer/auto/RV Typical Substrates:  Glass, aluminum, tile, fiberglass, plastic, ceramic, masonry, concrete, brick and wood Advantages: Extremely long service life Excellent flexibility for dynamic joint movement Bonds to most substrates without priming Ready to use, no mixing required AAMA Certified component for window backbedding/glazing All season ease of application Fungicide additive for mildew resistance

Cell 18" 295-PW White Global Antenna - 9dB Digital Antenna's new 9dB gain global cellular antenna is designed and manufactured for all cellular systems, including third generation (3G) and WCDMA technology. It improves signals on all cellular bands (850, 900, 1800, 1900 and 2100 MHz), offering excellent performance in a compact design. Ideal for many land and marine applications, including boats, RVs, homes and offices. Includes stainless steel L-bracket and U-bolts for mounting to a wall or pole. Made in the USA; assembled, tested and tuned by hand for maximum performance, quality and durability. Features: Powerful brass radiators Soldered connections Power directing ferrite choke bead High gloss urethane finish 316 stainless steel ferrule 9dB gain This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

15' White Coiled Hose with Adjustable Nozzle Features: 15' White Coiled Hose with Nozzle Male fitting: 3/4" Female Fitting: 3/4" Material: Polyrethane Hose