Elastomeric Marine Sealant - 10oz Cartridge - Clear A one-part, fast skinning (10 minutes) and fast curing (24 hours) multi-purpose marine grade sealant with superior strength, adhesion, elongation and life characteristics. Cures in temperatures of -20°F (-28.9°C) to 120°F (48.9°C) and can be wet sanded and painted after curing. Flexibility and compression capabilities are excellent. Heavy duty use above or below the waterline. Twists, bends, expands, compresses. Seals ports, beds hardware, stops leaks. Resistant to teak cleaners, oil, diesel fuel and salt water. Adheres tenaciously without primers to fiberglass, glass, plastic, metal and wood. Simple clean up with mineral spirits. Not recommended for wooden deck seams or use in areas subject to gasoline. WARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Elastomeric Marine Sealant - 10oz Cartridge - White A one-part, fast skinning (10 minutes) and fast curing (24 hours) multi-purpose marine grade sealant with superior strength, adhesion, elongation and life characteristics. Cures in temperatures of -20°F (-28.9°C) to 120°F (48.9°C) and can be wet sanded and painted after curing. Flexibility and compression capabilities are excellent. Heavy duty use above or below the waterline. Twists, bends, expands, compresses. Seals ports, beds hardware, stops leaks. Resistant to teak cleaners, oil, diesel fuel and salt water. Adheres tenaciously without primers to fiberglass, glass, plastic, metal and wood. Simple clean up with mineral spirits. Not recommended for wooden deck seams or use in areas subject to gasoline. WARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Elastomeric Marine Sealant - 10oz Cartridge - Black A one-part, fast skinning (10 minutes) and fast curing (24 hours) multi-purpose marine grade sealant with superior strength, adhesion, elongation and life characteristics. Cures in temperatures of -20°F (-28.9°C) to 120°F (48.9°C) and can be wet sanded and painted after curing. Flexibility and compression capabilities are excellent. Heavy duty use above or below the waterline. Twists, bends, expands, compresses. Seals ports, beds hardware, stops leaks. Resistant to teak cleaners, oil, diesel fuel and salt water. Adheres tenaciously without primers to fiberglass, glass, plastic, metal and wood. Simple clean up with mineral spirits. Not recommended for wooden deck seams or use in areas subject to gasoline. WARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Silicone Rubber Sealant Cartridge - Clear An all-purpose, non-corrosive, non-yellowing, mildew resistant, low-odor, 100% marine high quality silicone sealant. Tack-free in 30 minutes or less. *Fully cured in 24 hours. For use above or below the waterline. Will not shrink, crack, or dry out. Superior flexibility and adhesion to fiberglass, plastic, metal, and wood. Retains flexibility and tensile strength even after years of exposure. Acid free cure will not corrode metal.

LifeSeal® Sealant Cartridge - Clear A unique combination of marine silicone and polyurethane, formulated especially for fiberglass. LifeSeal® offers a fast-curing, low odor, high adhesion, non-sagging, non-corrosive, non-yellowing formula. It provides a durable permanent watertight seal for joints subject to structural movement. May be used above and below the waterline. Use for sealing decks to hulls, thru-hull fittings, vinyl ports, sealing/glazing windshields and bedding marine hardware. Will adhere to metal, glass, wood, Lexan®, ABS® and certain other materials. Can be removed without damaging gel-coat. Not recommended for ferro cement hulls, impregnated wood or oil-soaked materials. Cures in presence of water. Mildew resistant and acid free.

  Scanstrut is an international leader in the design and manufacture of outdoor and marine equipment. Renowned around the globe for its strict product testing, all mounts, chargers, and seals meet the highest and most demanding set of performance standards.     The Scanstrut PowerTower has been designed and engineered to install your radar on the roof, T-top, flybridge, or radar arch of your powerboat, providing the clearest view of the horizon allowing you to get the best performance from your radar in all conditions.   Designed to fit the most up to date radars from Garmin, Lowrance, Raymarine, Simrad, and Furuno Pre-drilled mounting holes allow the radar to fasten straight to the PowerTower No need to cut the radar’s connectors off for installation Marine sealant not required Available in 2 heights Available in Aft or Forward leaning designs Range of accessories light bars can be bolted to the back of the PowerTower     Securely holds and wirelessly charges your phone even in the toughest conditions. Now you can keep your phone in reach, fully charged, and ready to go. 12/24V 100% Waterproof Mount & charge One-handed operation Works with wireless charging enabled phones of all sizes Works through non-metallic, waterproof cases     Scanstrut's range of cabling solutions eliminates time-consuming, sub-standard routing of cables and messy sealant to achieve a 100% watertight installation for your marine cables every time.   IPX68 waterproof range Easy fit cable routing that cuts down your installation time. A guaranteed 100% watertight seal Marine sealant not required       Specials    Closeouts    Remanufactured    Rebates

      Sprayway manufactures a complete line of industrial MRO, automotive, screen print and housekeeping products since 1947. Sprayway has been an innovative industry leader, and its Sprayway Glass Cleaner is recognized as "The World's Best." From marine detailing to industrial maintenance, whether it is a detailing wax or an industrial lubricant, Sprayway provides wide-ranging industries with the products they need.     The World's Best Glass Cleaner - Excellent for windows, mirrors, windshields and other glass surfaces! For cleaning and polishing glass, mirrors, windshields and windows. This easy-to use, fast acting product uses a clinging foam to break up soils and hold them - even on vertical surfaces. There is no dripping, no running and no streaking. With an exclusive formulation using denatured alcohol and no ammonia, this product cleans thoroughly, dries quickly, requires no rinsing and leaves a pleasant, fresh aroma.   SHOP: https://www.clrmarine.com/462m4/manufacturers/s/sprayway.html     Specials    Closeouts    Remanufactured    Rebates  

Elastometric 3 oz (89ml) Sealant Tube - Clear A one-part, fast skinning (10 minutes) and fast curing (24 hours) multi-purpose marine grade sealant with superior strength, adhesion, elongation and life characteristics. Cures in temperatures of -20°F (-28.9°C) to 120°F (-48.9°C) and can be wet sanded and painted after curing. Flexibility and compression capabilities are excellent. Heavy duty use above or below the waterline. Twists, bends, expands, compresses. Seals ports, beds hardware, stops leaks. Resistant to teak cleaners, oil, diesel fuel and salt water. Adheres tenaciously without primers to fiberglass, glass, plastic, metal and wood. Simple clean up with mineral spirits. Not recommended for wooden deck seams or use in areas subject to gasoline. Features: Twists, bends, expands, compresses Seals ports, bed hardware and stops leaks Perfect for trim tabs and transducers WARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 291 LOT Slow Cure Adhesive & Sealant 10.3oz(300ml) Cartridge - White Sikaflex®-291 LOT is a 1-component, marine grade polyurethane elastomeric adhesive and sealant. It is a moisture cured, non-sag system designed with a long open time for jobs that require more time. Uses: General all-purpose, high strength marine sealant, which may be used for light duty bonding with long open time capability for humid climates or jobs requiring more time that remain permanently elastic. Characteristics & Advantages: Use above and below water line Resists salt water Paintable and sandable Excellent bond NSF approved for potable water USDA approved for incidental food contact WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 291 LOT Slow Cure Adhesive & Sealant 10.3oz(300ml) Cartridge - Black Sikaflex®-291 LOT is a 1-component, marine grade polyurethane elastomeric adhesive and sealant. It is a moisture cured, non-sag system designed with a long open time for jobs that require more time. Uses: General all-purpose, high strength marine sealant, which may be used for light duty bonding with long open time capability for humid climates or jobs requiring more time that remain permanently elastic. Characteristics & Advantages: Use above and below water line Resists salt water Paintable and sandable Excellent bond NSF approved for potable water USDA approved for incidental food contact WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Elastometric 3 oz (89ml) Sealant Tube - White A one-part, fast skinning (10 minutes) and fast curing (24 hours) multi-purpose marine grade sealant with superior strength, adhesion, elongation and life characteristics. Cures in temperatures of -20°F (-28.9°C) to 120°F (-48.9°C) and can be wet sanded and painted after curing. Flexibility and compression capabilities are excellent. Heavy duty use above or below the waterline. Twists, bends, expands, compresses. Seals ports, beds hardware, stops leaks. Resistant to teak cleaners, oil, diesel fuel and salt water. Adheres tenaciously without primers to fiberglass, glass, plastic, metal and wood. Simple clean up with mineral spirits. Not recommended for wooden deck seams or use in areas subject to gasoline. Features: Twists, bends, expands, compresses Seals ports, bed hardware and stops leaks Perfect for trim tabs and transducers WARNING: This product can expose you to chemicals including Toluene which is known to the State of California to cause birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Sikaflex® 295 UV - White - 10oz Tube with Nozzle Exterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).   Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of Application Sikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.  Application: Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting Sikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

Sikaflex® 295 UV - Black - 10oz Tube with Nozzle Exterior sealant and direct glazing adhesive for organic glass in Marine applications. Sikaflex®-295 UV is a 1-component polyurethane adhesive of paste-like consistency that cures on exposure to atmospheric moisture. It is suitable for interior and exterior sealing applications and to bond organic glass in the Marine business. Sikaflex®-295 UV meets the requirements set out by the International Maritime Organization (IMO).   Features: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Areas of Application Sikaflex®-295 UV has been specially developed for the marine industry, where it is used to bond and seal plastic glazing materials in boats and ships. Because of its excellent weatherability this product can also be used to seal joints in exposed areas. Suitable substrates are aluminum (bright or anodized), GRP (polyester resin), stainless steel, timber, 2-component coatings, and plastic glazing materials (PC, PMMA). Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-295 UV on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Product Benefits: Excellent application properties Resistant to aging and weathering Suitable for organic glasses Approved for the OEM market Wheelmark approved Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, dust, and contaminants. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.  Application: Sikaflex®-295 UV can be processed between 10 °C and 35 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. To ensure a uniform thickness of the bonding it is recommended to apply the adhesive in form of a triangular bead. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the product. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-295 UV can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting Sikaflex®-295 UV can be painted prior to and after the formation of the skin. If the painting process takes place after the sealant has built a skin, adhesion could be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 prior to the painting process. If the paint requires a baking process (> 80 °C), the best performance is achieved by allowing the sealant to fully cure first. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than that of sealants. This could lead to cracking of the paint in the joint area.

Sikaflex® 292i - White - 10oz Tube with Nozzle Sikaflex®-292i is a non-sag 1-component polyurethane adhesive of thixotropic, paste-like consistency which cures on exposure to atmospheric moisture. It exhibits excellent adhesive properties and good mechanical strength. Sikaflex®-292i meets the low spread of flame requirements set out by the International Maritime Organisation (IMO).   Features: Good gap-filling properties Can be painted Bonds well to a wide variety of substrates Areas of Application: Sikaflex®-292i is suitable for structural joints in marine constructions which will be subjected to high dynamic stresses. It is suitable to bond metals, particularly aluminum (including anodized finishes), metal primers and paint coatings (2-component systems), or ceramic materials, plastics such as GRP (unsaturated polyester resin), ABS, etc. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-292i on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed ensuring adhesion and material compatibility.   Benefits: Good gap-filling properties Can be painted Bonds well to a wide variety of substrates Wheelmark approved Solvent-free and very low VOC Surface Preparation: Surfaces must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long-lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application: Sikaflex®-292i can be processed between 10 °C and 40 °C (climate and product) but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Consider that the viscosity will increase at low temperatures. For easy application, condition the adhesive at ambient temperature prior to use. Tooling & Finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended to use Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior to the use.  Removal Uncured Sikaflex®-292i can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using Sika® Cleaner-350H cleaning towels or a suitable industrial hand cleaner and water. Do not use solvents on the skin.

Sikaflex®-715 - White - 300ml Cartridge Semi self-leveling roof membrane sealer. Sikaflex®-715 is a one-component silane terminated polymer (STP) sealant that cures on exposure to atmospheric humidity.  Its unique flow characteristic is designed for roof sealing applications.  Sikaflex®-715 has very good adhesion and UV resistance making it suitable for open joints.   Features: Primerless adhesion to the difficult substrate Semi self-leveling for roof sealing Very good dispensing characteristics Isocyanate free Low VOC content Very good UV resistance Usage: Sikaflex®-715 is suitable for sealing a wide variety of RV roofing components including, EPDM; metals such as anodized and bare aluminum; phosphate, chromate, and zinc-plated steel; metal primers; 2-part coatings; ceramics and plastics. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-715 on materials prone to stress cracking. This product is suitable for experienced professional users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface Preparation: Surfaces must be clean, dry and free from grease, oil and dust. For repairs, removal of pre-exisiting products is crucial to avoid compatibility issues.  Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Adhesion and compatibility have to be verified by tests on original substrates. Application: Sikaflex®-715 can be processed between 5 °C and 40 °C (41 °F and 104 °F) but, changes in reactivity and application properties have to be considered. The optimum temperature for substrate and process material is between 15 °C and 25 °C (59 °F and 77 °F). Sikaflex®-715 can be processed with manual, pneumatic, or electric-driven piston guns as well as pump equipment. Removal: Uncured Sikaflex®-715 may be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically.  Hands and exposed skin have to be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin. Overpainting: Sikaflex®-715 is not suitable for overpainting. Specifications: Chemical base: Silane Terminated Polymer Color (CQP001-1): White, black Cure mechanism: Moisture-curing Density (uncured): 1.52 kg/l (12.7 lb/gal) Non-sag properties: Semi self-leveling Application temperature: 5-40 °C (41-104 °F) Skin time (CQP019-1): 30 minutes A Shore A hardness (CQP023-1 / ISO 48-4): 10 Tensile strength (ASTM D412): 0.6 MPa (85 psi) Elongation at break (ASTM D412): 500% Service temperature (CQP513-1): -50-90 °C (-58-94 °F)