No. 1091 - Longarm Downrigger Combo Pack (36"-60") Ideal for big boats. All the same features as the 1090 plus with the addition of the Pedestal Swivel Mount. PRODUCT OVERVIEW:  High speed, 2 ft. per turn of the spool coupled with an extended handle for extra leverage Spray protected positive-drive depth counter 200 ft. of 150 lb. Test, Stainless Steel Downrigger Cable Boom mounted adjustable 358 Rodmaster II Rod Holder Marine grade stainless steel boom Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position Includes 1026 Swivel Pedestal Mount with 16 available positions Clutch brake with the largest braking surface in the industry – In the event of a bottom hang-up, it will pay out to avoid loosing gear Includes Power Grip Plus Line Release Fully assembled and factory tested with complete saltwater protection Downrigger Boom Length: 36″-60″ telescoping stainless steel boom Downrigger Boom Diameter: 1 1/4″ Rod Holder Interior Diameter: 1.85″ WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Swivel Base Rod Holders RH570XL Stainless Steel Side Mount w/ Swivel Base Extra Long This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface. Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.

Swivel Base Rod Holders RH570 Stainless Steel Side Mount w/ Swivel Base Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a inch stainless steel lock nut at the bottom of the rod holder.

2116 HP Electric Downrigger (36"-60") The number one choice in trolling performance for the charter captain. Equipped with heavy duty, adjustable dual rod holders and all the other great features of our heavy duty, High Performance Downriggers. PRODUCT OVERVIEW:  Unbeatable pulling power lifts 15 lb. weights at 295 ft./min. and 20 lb. weights with ease at 260 ft./min. Includes Illuminated, resettable, sealed and silent digital line counter 300 ft. of 180 lb. Test, HP Stainless Steel Downrigger Cable Dual adjustable and stainless steel jacketed Rocket Launcher Rod Holder (No. 447) Includes Scotty/Marinco™ Plug and Receptacle Includes 1148 Weight Storage Hook and marine grade stainless steel boom Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position Multi-position auto-stop included (Use 1008 Stopper Beads to stop at any pre-set position) Includes Power Grip Plus Line Release 1/2″ Kevlar drive belt by Optibelt™ – The same belts used by superior European auto manufacturers Clutch brake with the largest braking surface in the industry Includes 1026 Swivel Pedestal Mount with 16 available positions Fully assembled and factory tested with complete saltwater protection Downrigger Boom Length: 36″ – 60″ telescoping stainless steel boom Downrigger Boom Diameter: 1 1/4″ Rod Holder Interior Diameter: 1.70″ WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Swivel Base Rod Holders RH575 Standard Angle 30° Stainless Steel Flush Mount w/ Swivel Base Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.

Swivel Base Rod Holders RH575XL Standard Angle 30° Stainless Steel Flush Mount w/ Swivel Base Extra Long This holder is 4" longer than the standard length allowing the bent butt to sit deeper in the holder thus reducing the leverage and stress on the mounting surface. Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.

Swivel Base Rod Holders RH579 Half Angle 15° Stainless Steel Flush Mount w/ Swivel Base Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.

Swivel Base Rod Holders RH579XL Half Angle 15° Extra Long Tube Stainless Steel Flush Mount w/ Swivel Base Without a doubt, our swivel base rod holder is the Ultimate Rod Holder for the serious sportsman. Primarily designed to be used with bent butt tackle, the rod holders unique swivel base allows the rod butt to rotate in the rod holder when side pressure is applied to the tip of the rod. This is an indispensable tool, especially important in Giant Blue Fin Tuna fishing, where reel drags in the neighborhood of 60 pounds are frequently used and can result in tremendous forces being applied to the rod holder pin. Not only does this make sheared rod holder pins a thing of the past but, more importantly, it allows the tip of the rod to follow the fish. This reduces the possibility of line fraying and enhanced drag as the line streams sideways out of the roller tip instead of over the roller. The rod is also more easily removed from the holder since it is not locked on a rigid pin. The swivel base holder functions as a standard rod holder when used with straight butt rods. Straight butt rods can be manually rotated so that the line remains on the tips roller. The amount of torque required to rotate the swivel is set by adjusting the pressure on two nylon drag washers with a 1/2 inch stainless steel lock nut at the bottom of the rod holder.

High Performance Electric Downrigger The High Performance Downrigger features a new illuminated digital line counter as well as the sleek new Rocket Launcher rod holder. Pre-spooled with the HP stainless steel downrigger wire, the HP models have unbeatle pulling power lifting 20 lb. weights with ease at 260 ft. / min, and 10 lb. weights at 312 ft. / min. Includes: 36" - 60" telescoping stainless steel boom. 1 1/4" dia. Illuminated, resettable, sealed and silent digital line counter 300 ft. of 180 lb. Test, 316 stainless steel downrigger wire 1/2" Kevlar drive belt by Optibelt TM - The same belts used by superior European auto manufacturers Clutch brake with the largest braking surface in the industry Boom mounted adjustable Rocket Launcher Rod Holder Swivel Pedestal Mount WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Depthpower 60" Electric Downrigger w/200lb Test Braid The most popular Scotty Electric Downrigger, with a boom that telescopes for extra reach and collapses for storage. Makes for a great “big boat” downrigger. PRODUCT OVERVIEW:  Fully adjustable decent speed, lifts 7 lb. weights at 235 ft./min. and 15 lb. weights at 203 ft./min. Spray protected positive-drive depth counter and Kevlar drive belt by Optibelt™ 300 ft. of 200 lb. test, low drag microfilament premium power braid downrigger line (No. 2701) Boom mounted adjustable 358 Rodmaster II Rod Holder Includes Scotty/Marinco™ Plug and Receptacle The lowest amperage draw of any downrigger made with less than 1/3 the battery draw than some of the competition Marine grade stainless steel boom Multi-position auto-stop included (Use 1008 Stopper Beads to stop at any pre-set position) Includes Power Grip Plus Line Release Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position Includes 1026 Swivel Pedestal Mount with 16 available positions Fully assembled and factory tested with complete saltwater protection Downrigger Boom Length: 36″-60″ telescoping stainless steel boom Downrigger Boom Diameter: 1 1/4″ Rod Holder Interior Diameter: 1.85″ WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Uni-Troll 10 Take command of controlled depth fishing when you equip your boat with a Uni-Troll downrigger. features an innovative design that lets you pull your lines back in with less cranking effort and One-Hand Clutch Deploy for simple precise bait positioning. Built with a 2:1 retrieval speed, a low-profile swivel base and a heavy-duty telescopic boom that extends from 24" to 53". More control at every turn. Take command of controlled depth fishing when you equip your boat with our Uni-Troll™ manual downriggers. Perfect for smaller boats, each model allows for quick line retrieval and controlled, one-handed weight descent. FAST RETRIEVAL RATE Our Uni-Troll and Easi-Troll models feature an innovative design that lets you pull your lines back in with less cranking effort. The quicker you can retrieve your lines, the quicker you can get back to catching fish. CONTROLLED WEIGHT DESCENT Get controlled, accurate bait positioning thanks to the One-Hand Clutch Deploy on all Cannon manual downriggers. It's designed to gradually, precisely lower your weight and lure into the strike zone. Features: Fast, effortless 2:1 retrieval speed One-Hand Clutch Deploy for simple, precise bait positioning Enclosed boom end pulley prevents line jumping Easy-Access Universal Mounting Base - same as our electric models Dual axis rod holder - fully adjustable, both front to back and side to side Ergonomic crank handle Integrated ball storage hook Three-digit depth counter Pre-spooled with 200' of 150-lb test stainless steel cable and includes a line release Includes - Universal Mounting Base, Low-Profile Swivel Base, line terminator, one (1) Uni-line releases, and ergonomic crank handle. Limited lifetime warranty WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Uni-Troll™ 5 ST Manual Downrigger Trolling Kit All-in-one trolling kit Designed for smaller boats Includes: Uni-Troll 5 ST Manual Downrigger 6lb Cannon Flash Weight Universal Line Release Swivel Base Take command of controlled depth fishing when you equip your boat with a Uni-Troll™ downrigger - features an innovative design that lets you pull your lines back in with less cranking effort. Built with a 2:1 retrieval speed and a 24" heavy-duty boom. Features: Fast, efficient 2:1 retrieval speed One-Hand Clutch Deploy for controlled, precise bait positioning Heavy-duty 24" boom Enclosed boom end pulley prevents line jumping Easy-Access Universal Mounting Base (interchangeable with our electric models) Dual axis rod holder - fully adjustable, both front to back and side to side Ergonomic crank handle Integrated ball storage hook Three-digit depth counter Pre-spooled with 200' of 150lb test stainless steel cable and includes a line release

No. 1085 Strongarm Downrigger (30") The heavy duty workhorse of the Scotty manual lineup. Excellent for the intermediate size boat. PRODUCT OVERVIEW:  High speed, 2 ft. per turn of the spool coupled with an extended handle for extra leverage Spray protected positive-drive depth counter 200 ft. of 150 lb. Test, Stainless Steel Downrigger Cable Boom mounted adjustable 358 Rodmaster II Rod Holder Marine grade stainless steel boom Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position Clutch brake with the largest braking surface in the industry – In the event of a bottom hang-up, it will pay out to avoid loosing gear Includes Power Grip Plus Line Release Fully assembled and factory tested with complete saltwater protection Downrigger Boom Length: 30″ stainless steel boom Downrigger Boom Diameter: 1 1/4″ Rod Holder Interior Diameter: 1.85″ WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

NEW - Innovative Trolling System Puts You In Control Aluminum Swivel Base Downrigger Pedestal For surface or track mounting, this smooth action swivel base provides for 360° rotation, with 16 locking points spaced every 22.5°. The top plate is pre-drilled and tapped for mounting Cannon downriggers, as well as other downrigger brands.

NEW - Innovative Trolling System Puts You In Control Aluminum Swivel Base Downrigger Pedestal For surface or track mounting, this smooth action swivel base provides for 360° rotation, with 16 locking points spaced every 22.5°. The top plate is pre-drilled and tapped for mounting Cannon downriggers, as well as other downrigger brands.