SI-TEX 492/50/200 In-Hull Transducer f/ES502 Dual Frequency 50/200 kHz Max Power: 500W Beam Angle: 42 deg. @ 50 kHz, 12 deg. @ 200 kHz Housing: Plastic Mount: In-Hull Plug: 8 pin Cable: 30' Temp: No Speed: No For SI-TEX model: ES502

SI-TEX 492/50/200ST Transom Mount Transducer f/ES502 Dual Frequency 50/200 kHz Max Power: 500W Beam Angle: 42 deg. @ 50 kHz, 12 deg. @ 200 kHz Housing: Plastic Mount: Transom Plug: 8 Cable: 30' Temp: Yes Speed: Yes For SI-TEX model: ES502

SI-TEX 250/50/200ST Transom Mount Transducer Dual Frequency 50/200 kHz Max Power: 600W Beam Angle: 45 deg. @ 50 kHz, 11 deg. @ 200 kHz Housing: Plastic Mount: Transom Plug: 8 pin Cable: 30' Temp: Yes Speed: Yes For SI-TEX model: CVS106MKIIDF, 106L, 106MKII, 832, 833, Genesis

XP-14-HW Dual Spectrum CHIRP In-Hull Transducer for SOLIX™ In-Hull Dual Spectrum CHIRP Transducer supports Dual Spectrum CHIRP 2D Sonar with high frequency beam and wide cone angle, offering CHIRP range of 150-220kHz and max depth of 1200ft. Intended for glue-in installation inside single layer fiberglass hulls. Includes epoxy kit and 20’ cable.  Features: This accessory is compatible with the following Humminbird products: SOLIX 10, 12, 15 – All G2 Models. Side Imaging™ and Down Imaging™ units can support the XP 14 HW as a sonar only transducer. This transducer does not support Side Imaging or Down Imaging. Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz Dual Spectrum CHIRP Max Depth: 1200ft (365m) WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SI-TEX 496/50/200ST Bronze Thru-Hull Transducer w/ Fairing Block f/ ES502 Dual Frequency 50/200 kHz Max Power: 500W Beam Angle: 42 deg. @ 50 kHz, 12 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: 8 pin Cable: 30' Temp: Yes Speed: Yes For SI-TEX model: ES502

SI-TEX 300/50/200T Bronze Thru-Hull Transducer Dual Frequency 50/200 kHz Max Power: 600W Beam Angle: 43 deg. @ 50 kHz, 9 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: Two 8 pin Cable: 30' Temp: Yes Speed: No For SI-TEX model: CVS208/209

SI-TEX 307/50/200T Transducer f/CVS-832 Dual Frequency 50/200 kHz Max Power: 1kW Beam Angle: 22 x 45 deg. @ 50 kHz, 6 x 11 deg. @ 200 kHz Housing: Bronze Mount: Through Hull Plug: 8 pin Cable: 30' Temp: Yes Speed: No For SI-TEX model: CVS862, 832C, 833C, Genesis

SI-TEX 250C/50/200ST Transducer Dual Frequency 50/200 kHz Max Power: 1kW Beam Angle: 45 deg. @ 50 kHz, 11 deg. @ 200 kHz Housing: Plastic Mount: Transom Plug: 8 pin Cable: 30' Temp: Yes Speed: Yes For SI-TEX model: CVS832C, 833C, Genesis

120kHz Bronze Thru-Hull Transducer f/SDD-110  Features: 120kHz Bronze Thru-Hull Transducer Specifically for SI-TEX SDD-110

250C/50/200ST-CX Transom Mount Transducer SI-TEX 250C/50/200ST-CX Transom Mount Transducer for the CVS-126 and CVS-128.

120 kHz Lexan Low-Profile Thru-Hull Transducer f/SDD-110 Seawater Depth Indicator.

Adjustable In-Hull Transducer 600 Watt adjustable angled in hull transducer. (P79) Compatible with the following Echo Sounders: SL Series: SL755RC, SL760RC , SL1250, and SL1250RC hsb2 Plus Series: L755RC, L760, L760RC, L1250,and L1250RC hsb2 HDFI Series: DSM250, L770D, L770DRC, L1260D, and L1260DRC Compatible hull material: fiberglass Max Power: 600 W Frequency: 200/50 kHz Beam Angles: 200 kHz 11 50 kHz 45 Features: Depth only. Can be used in conjunction with the E66019 ST69 speed and temperature sensor Easily adjusts to any deadrise angle up to 22 Transmits sound waves directly at the bottom so strong echoes are reflected back to the transducer Can be removed in seconds for servicing or storage Only the base piece is bonded to the hull. There is no adhesive layer under the transducer face to absorb sound energy Simplifies in-hull installation 30ft (10m) Cable

Airmar P79 Adjustable 200/50kHz Plastic In-hull Transducer (8-pin) 010-10327-20 This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap. The 8-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise. Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat. *Fiberglass should be no more than 5/8" thick. Not recommended for cored hulls. When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

R111-LH Chirp In-Hull Transducer - Bare Wire Rely on Airmar’s new broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 117 kHz of total bandwidth in just one installation, saving customers time and money. A Hard-Core In-Hull model in the Chirp Thru-Hull product line L/H Chirps across the following bandwidths: L/H Model -Low Frequency 38-75 kHz, High Frequency 130-210 kHz Features Depth & fast-response water-temperature sensor Low—CHIRPS from 38 kHz to 75 kHz 19° to 10° beamwidth High—CHIRPS from 130 kHz to 210 kHz 8° to 4° beamwidth 117 kHz of total bandwidth from one transducer Covers popular fishing frequencies of 38, 50, and 200 kHz plus everything else in the bandwidth Fishing Profile: Recreational and commercial inshore and offshore fishing (deep-water canyon and sea-mount tracking) Urethane transducer housing Hull Type: Solid fiberglass only Exclusive Xducer ID® technology Hull Deadrise: 0° to 22° Acoustic Window: Epoxy/urethane All mounting hardware provided, including tank Weight: 19.7 kg (43.4 lb) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Active Imaging 2-in-1 Transducer & 83/200 Pod In-Hull Transducer with Y-Cable  Allows for connection of an in-hull puck transducer and an Active Imaging 2-in-1 (Side/Down) transducer to the single sonar port of an Elite Ti2 or Elite FS display. Features: Active Imaging 2-in-1 Transom Transducer 83/200 Pod/Puck Transducer without temperature Dual 9-pin Y-cable