Tough-Track™ for '21-23 Ford Bronco The RAM® Tough-Track™ for '21-23 Ford Bronco (RAM-DT-207-TRACK-EXA-29BU) converts a dashboard into a full-length track mounting area. This dashboard mount consists of two top-loading black aluminum 13" RAM® Tough-Track™s attached to three high-strength composite grips, custom fit the Bronco accessory-ready area — no drilling required. Installation is easy, simply remove the center hex bolt, align the grips to the defrost ducts, and reinstall the hex bolt through the center grip. For a fumble-free device mount installation with no tools, hand tighten RAM® Track Ball™ components along with double socket arms and device holders for phones, small tablets, GPS units, radios, cameras, and more. Install this Ford Bronco dashboard track mount with no drilling or modifications required. Thoughtfully designed with rounded edges to ensure dashboards stay pristine, avoiding scuffs and nicks during the installation. Features: Installs directly onto the dashboard of '21-'23 Ford Bronco models via defrost duct hooks and an existing hex bolt, with no drilling or modifications necessary Rounded edges are thoughtfully designed to avoid scuffing the dashboard surface The top-loading track is compatible with RAM® Track Ball™ bases for fumble-free accessory mount installation Made of powder-coated steel and high-strength composites for durability and reliability in the most demanding environments Backed by a lifetime warranty Specifications: Hardware Included: Assembly hardware Product Dimensions: 29 in. inside track length Materials:  Marine-grade aluminum and high-strength composite  Weight: 2.0 lb. Compatibility This dash mount for the Ford Bronco is compatible with all models, including the base model, Big Bend, Black Diamond, Outer Banks, Badlands, Wildtrak, Everglades, Heritage, and Raptor.

Tough-Track™ for 18-19' Jeep JL/Gladiator The RAM® Tough-Track™ for the dash of 2018-2019 Jeep JL/Gladiator vehicles creates an ideal device setup for overland and off road enthusiasts. Consisting of a dash mounting plate (screws included) and a top-loading composite 12” RAM® Tough-Track™, easily attach RAM® Track Ball™ components along with double socket arms and device holders for phones, small tablets, GPS units, radios, cameras, and more.  Specifications: Materials: Powder coated steel, High strength composite Hardware Included: Assembly Hardware Product Dimensions: Inside Track Length: 12" Track Dimensions: Track length: 14.5" Track width: 1.75" Track thickness: .35" Inside track length: 12"

Tough-Track™ Overall Length - 7" With the RAM Tough-Track, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks, and more. This track mount solution can be drilled to any flat surface and is designed for use with #10 screws for easy installation – hardware not included. The Tough-Track works with a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones, and tablets.  Material: High Strength Composite Dimensions: Overall length: 7" Overall width: 1.75" Track thickness: .35" Inside track length: 5"

Tough-Track™ Overall Length - 14.5" With the RAM Tough-Track, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks, and more. This track mount solution can be drilled to any flat surface and is designed for use with #10 screws for easy installation – hardware not included. The Tough-Track works with a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones, and tablets.  Material: High Strength Composite Dimensions: Overall length: 14.5" Overall width: 1.75" Track thickness: .35" Inside track length: 12"

Tough-Track™ Overall Length - 18.5" With the RAM Tough-Track, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks, and more. This track mount solution can be drilled to any flat surface and is designed for use with #10 screws for easy installation – hardware not included. The Tough-Track works with a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones, and tablets.  Material: High Strength Composite Dimensions: Overall length: 18.5" Overall width: 1.75" Track thickness: .35" Inside track length: 16"

Tough-Track™ Overall Length - 10.75" With the RAM Tough-Track, flat surface mounting possibilities are nearly endless for ATVs, cars, combines, motorboats, tractors, trucks, and more. This track mount solution can be drilled to any flat surface and is designed for use with #10 screws for easy installation – hardware not included. The Tough-Track works with a wide variety of RAM track bases to attach devices like action cameras, fishing rods, phones, and tablets.  Material: High Strength Composite Dimensions: Overall length: 10.75" Overall width: 1.75" Track thickness: .35" Inside track length: 9"

No-Drill™ Laptop Mount Vehicle System for '17-20 Ford F-Series + More This RAM® No-Drill™ laptop stand system installs quickly and easily into a variety of Dodge, Ford, and Jeep vehicles using the existing hardware of the passenger side seat rails. This configuration provides a telescoping feature that ranges from 12” to 18”. Dual swing arms provide articulation and 12” of reach for passenger and driver access to the mounted device. RAM® rubber ball and socket technology provides additional adjustability as well as shock and vibration isolation. The spring-loaded RAM® Tough-Tray™ laptop holder accommodates 10” to 16” wide laptops, and 17” wide screens. The tray features four adjustable retaining arms with rubber grips that can be moved both vertically and horizontally. These arms allow for a custom fit for laptops of varying thickness while not blocking drives or ports. A screen support and USB light are also available to accessorize the RAM® Tough-Tray™. In addition, hole patterns on the perimeter of the laptop holder are compatible with several RAM® mounting solutions.  Features: Placement of Mount: Passenger side, in front, where seat frame meets floor board Drilling Requirements: None. Utilizes existing vehicle mounting points and hardware Seat Configuration: Bucket Material: High Strength Composite and Powder Coated Steel Custom, No-Drill™ mounting base offers lowest profile in the industry Ball and socket mounting system offers shock and vibration dampening Dual articulating swing arm offers the simplest and most comfortable adjustment points in the industry Combination Telescoping pole adjusts both height and swing with one knob Modular system makes changing your vehicle, or your device, simple and cost effective Ability to mount laptops, tablets and other devices using the same mounting system Universal Laptop Tray accommodates most laptops Compatible Devices 10" to 16" Wide Laptops & (17" Wide Screens) Compatible Vehicles Dodge Journey (2011-2020) Ford F-150 (2015-2020) F-250-F-550 (2017-2020) Escape (2013-2019) Expedition (2018-2021) Transit Connect (2014-2021) C-Max (2014-2018) Focus (2011-2018) Raptor (2015-2020) Jeep Compass (2013-2021) Patriot (2013-2017)

Tough-Tube™ Rod Holder with Track Base The Tough-Tube™ Rod Holder with Track Base kit is compatible with the RAM Tough-Track™ to provide an ideal fishing rod holder mounting solution. Attach the rod holder using the included track base and RAM ROD® ratchet attachment. The track base’s tether point secures your rod holder while the adjustable ratchet attachment allows for multiple angles, keeping you in control out on the water.  Features: 1. Quick release and installation 2. High strength materials ensure product longevity 3. Compatible with spinning reels and level wind reels 4. Ratchet system allows for multiple articulation points 5. Lanyard tie points for extra security 6. Custom designed for heavy chop environments 7. Mount virtually anywhere on heavy rigged kayaks without hinderance 8. Lifetime warranty 9. Made in U.S.A. Dimensions: Inner diameter: 1.9" Inner tube length: 10" (from bottom to top of lip) Post Spline Length: 3" Material: High Strength Composite Notes: Part number reflects product packaged in retail bag for store shelf display. Weight: 1.05 lbs.

RAM® Tough-Cleat™ for the Tough-Track™ Create an anchor tie-off point for your kayak with the RAM® Tough-Cleat™. While fishing on the river or lake, moving the Tough-Cleat to an ideal position is easy – simply loosen the knob and slide along your track mounting system. The Tough-Cleat features a T-Bolt attachment and is compatible with the RAM Tough-Track™.  Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. 

RAM® Tough-Clip™ Paddle Cradle with Track and Drill-Down Mounting Hardware The RAM Tough-Clip™ Paddle Cradle allows you to mount a paddle to your canoe, kayak or paddle board. With its universal design, the Tough-Clip™ will hold most paddles with a handle of 1”-1.31” in circumference. This kit includes hardware and instructions for both a drill-down installation option and a track mounting option that’s compatible with the RAM Tough-Track™. Material: High Strength Composite Note: Part number reflects product packaged in retail bag for store shelf display.

RAM® Vertical Track Tie Down – 2 Pack As a pack of two, the RAM® Vertical Track Tie Down system features a T-Bolt and provides an anchor point for use with a track mounting system, allowing you to secure coolers and other accessories to your kayak. Each tie down is designed to work with 1” and 1.5” flat webbing, as well as ropes and bungee cords up to 3/8”. Compatible with all versions of the RAM Tough-Track™.  Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag. 

PedestalPod with RAM Mount Pre-Cut for Lowrance HDS-9 Gen2 Touch, HDS-9 Gen3 & HDS Carbon 9 - Carbon Black PedestalPod with RAM Mounts is specifically designed for mounting the fishfinder near the bow on Bass Boats. Built on the foundation of NavPods popular range of waterproof housings for marine electronics, PedestalPods position your fishfinder/chartplotter at an easy to reach 20” off the deck. This allows the user easy access to the display for changes to range, zoom or even control the trolling motor. There is a big difference between reaching down to a height off the deck of 20” to control your fishfinder compared to reaching all the way down to the deck when it was only bracket mounted.  PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal. This offers protection of your fishfinder/chartplotter from the harshest of wet boating conditions.  This protection assures reliability and longevity of your marine electronics. PedestalPod with RAM Mounts utilizes the proven RAM Mounting system with the large 2.25” rubber “D” size ball and the RAM pin-lock security solution.  RAM Mounts are designed with a patented rubber ball and socket system that allows an almost infinite amount of ways to position the angle of the fishfinder for that precise position of viewing. When you might be trailering, or storing the boat, the display can fold flat onto the deck with only 10” of clearance.  This will allow most boat covers to fit over the PedestalPod when not in use. Your fishfinder is easily flush mounted into the pre-cut face of the NavPod. There are pre-cut models available for 7”, 9” and 12” LCD displays from all major marine electronic manufacturers. PedestalPods are waterproof housings for marine electronics specifically designed for bass boats. PedestalPods are better than bracket mounting. Very sturdy and secure, yet clean and attractive, this mount provides protection of your marine electronics from the harshest of wet boating conditions. PedestalPods provide the convenience of height for accessibility and added security with protection from theft. PedestalPods position your fishfinder/chartplotter at 20” off the deck and located near the bow and at a 45-degree angle for ease of viewing while fishing. This allows the user to easily reach and access the fishfinder/chartplotter for changes to range, zoom or even control the trolling motor. All NavPods are manufactured with a double gasket system that provides an excellent watertight seal. They keep harsh spray off the electrical connections on the back of your fishfinder/chartplotter assuring reliability and longevity of your marine electronics. Your fishfinder/chartplotter is easily flush mounted into the pre-cut face of the PedestalPod. The heavy duty, black powder coated aluminum pedestal tube is 3” in diameter with a 5” round base and has a large 1.75” opening providing plenty of room for running wires and connectors internally for a very clean look. It provides protection for wires and connectors from water intrusion, UV exposure or damage from just getting kicked or snagged and ripped out of their sockets. All NavPods come with a security wrench and nickel chrome-plated stainless steel tamperproof screws for protection from theft. PedestalPods are available pre-cut for 7”, 9” and 12” LCD displays from all major marine electronic manufacturers. Constructed out of durable ABS like all Gen3 NavPods, black carbon PedestalPods have the same high gloss finish with UV stability. NavPod backs up their commitment to quality by offering a 10-year warranty on all Gen3 NavPods. PedestalPods – Protection, Convenience, Security

PedestalPod with RAM Mount Pre-Cut for Lowrance HDS-9 MFD Gen2 Touch & HDS-9 Gen3 - Carbon Black PedestalPod with RAM Mounts is specifically designed for mounting the fishfinder near the bow on Bass Boats.  Built on the foundation of NavPods popular range of waterproof housings for marine electronics, PedestalPods position your fishfinder/chartplotter at an easy-to-reach 20” off the deck. This allows the user easy access to the display for changes to range, zoom or even control the trolling motor. There is a big difference between reaching down to a height off the deck of 20” to control your fishfinder compared to reaching all the way down to the deck when it was only bracket mounted. PedestalPods are manufactured with a double gasket system that provides an excellent watertight seal. This offers protection of your fishfinder/chartplotter from the harshest of wet boating conditions.  This protection assures the reliability and longevity of your marine electronics. The PedestalPod with RAM Mounts utilizes the proven RAM Mounting system with the large 2.25” rubber “D” size ball and the RAM pin-lock security solution. RAM Mounts are designed with a patented rubber ball and socket system that allows an almost infinite amount of ways to position the angle of the fishfinder for that precise position of viewing. When you might be trailering, or storing the boat, the display can fold flat onto the deck with only 10” of clearance.  This will allow most boat covers to fit over the PedestalPod when not in use. Your fishfinder is easily flush mounted into the pre-cut face of the NavPod. There are pre-cut models available for 7”, 9”, and 12” LCD displays from all major marine electronic manufacturers. PedestalPods – Protection, Convenience, Security.

Tough-Charge™ 15W Wireless Charging Mount with Tough-Claw™ The RAM® Tough-Charge™ with X-Grip® Technology is the world's first patented, universal, waterproof wireless charging cradle for phones. Designed with spring-loaded RAM® X-Grip® Technology, this cradle features an 'X' design that expands and contracts to secure nearly any phone while taking advantage of Qi wireless phone charging. All four arms feature rubber-coated caps that hold your phone firmly in place, and the open design keeps buttons and switches accessible on the sides of phones. To insert your device, simply squeeze the arms on one side of the cradle and place your phone inside before releasing the arms. This Qi wireless charging cradle ensures your compatible phone charges no matter what position it's placed at. For added security and peace of mind, a device tether is included that’s recommended for outdoor applications. In addition, a support leg can be adjusted to the ideal position or removed altogether. This RAM® Tough-Charge™ with X-Grip® Technology wireless charging kit includes a B-size diamond base featuring a 1" rubber ball, a short-length double socket arm, and a RAM® Tough-Claw™ clamping base. With the RAM® Tough-Claw™ base, you can easily attach the wireless phone charger to round, square, and odd-shaped rails and bars ranging from .625" to 1.14" in outer diameter. The connected Type-A male pigtail connector features an in-line switch that allows you to turn off the wireless charging module when not in use. For in-vehicle charging, attach the pigtail to the included 1.2m Type-A male to Type-A female extension cable. This kit includes a hardwired charger. Features: Waterproof Qi-compatible wireless phone charging cradle features spring-loaded RAM® X-Grip® technology and 15W maximum output Kit includes a wireless charging cradle, B-size diamond ball base, short double socket arm, RAM® Tough-Claw™ clamping base, and hardwire charger Made of powder-coated, marine-grade aluminum, stainless steel components, and high-strength composite for durability and reliability in the most demanding environments RAM® mounts are backed by a lifetime warranty, and RAM® electronics are backed by a 1-year warranty with proof of purchase required Specifications: Hardware Included: (1) Safety Tether, (1) Glue Tube for Rubber Caps, (1) Cradle Leg, (1) Cradle Leg Cover, (1) Silicon sleeve for USB waterproof connection, (1) Hardwire Charger with Cable, (4) Small zip ties, and (4) Large zip ties Holder Dimensions (inch): Width Range: 2.375" - 3.25", Depth Range: .875" max Clamp Range (inch): 625" - 1.14" diameter Socket-to-Socket Length (inch): 1.75” Ball Size (inch): B Size (1") Weight Capacity: Standard Use: 2 lbs / Heavy-Duty Use: 1 lbs Materials: High-strength composite and stainless steel Weight: 1.81 lb. Warranty: 1 year Power Specifications: Input Power: 5V-2A; 9V-1.67A Output: 15W Conversion Efficiency: 85% Max Maximum Case Thickness: 6mm Working Frequency: 110-205KHZ Product Standard: WPC v.1.2.4 Qi Compatible: Yes Compatible with QC2.0/QC3.0 power supplies Operating Temperature: 0°C to +37.7°C Compliance: Over Voltage Protection, Short Circuit Protection, Reverse Polarity Protection, RoHS Compliance, WEEE Compliance, SAE J-1113-5 Load Dump (Transient Voltage), Moisture Resistant Certifications: CE Certification, KC, e-Mark Certification, RCM Certification, FCC Certification Compatible Devices: Apple: iPhone 11, iPhone 11 Pro, iPhone 11 Pro Max, iPhone 8, iPhone 8 Plus, iPhone SE, iPhone X, iPhone Xr, iPhone Xs, and iPhone Xs Max Blackberry: Evolve X Blackview: BV9900 and BV9900 Pro Google: Pixel 3, Pixel 3 XL, Pixel 4, Pixel 4 XL, Pixel 5, Pixel 6, Pixel 6 Pro, Pixel 7, and Pixel 7 Pro Huawei: Mate 20 Pro, P30 Pro LG: G6, G6+, G7 ThinQ, G8 ThinQ, G8S ThinQ, V30, V35 ThinQ, V40 ThinQ, V50 ThinQ Nokia: 8 Sirocco and 9 PureView Razer: Phone 2 Samsung: Galaxy Note 10, Galaxy Note 10 Plus, Galaxy Note 5, Galaxy Note 8, Galaxy Note 9, Galaxy S10, Galaxy S10 5G, Galaxy S10+, Galaxy S10e, Galaxy S20, Galaxy S20+, Galaxy S20 Ultra 5G, Galaxy S21 5G, Galaxy S21+ 5G, Galaxy S21 Ultra 5G, Galaxy S22 5G, Galaxy S22+ 5G, Galaxy S22 Ultra 5G, Galaxy S23, Galaxy S23+, Galaxy S23 Ultra, Galaxy S6, Galaxy S6 Edge, Galaxy S6 Edge+, Galaxy S7, Galaxy S7 Active, Galaxy S7 Edge, Galaxy S8, Galaxy S8+, Galaxy S8 Active, Galaxy S9, and Galaxy S9+ Sony: Xperia XZ2, Xperia XZ2 Compact, and Xperia XZ3 Xiaomi: Mi 9, Mi 9 Explorer, Mi Mix 2S, and Mi Mix 3 ZTE: Axon 9 Pro, Axon 10 Pro

Tough-Charge™ with X-Grip® Tech Waterproof Wireless Charging Holder The RAM® Tough-Charge™ with X-Grip® Technology is the world's first patented, universal waterproof wireless charging cradle for phones. Designed with spring-loaded RAM® X-Grip® Technology, this cradle features an 'X' design that expands and contracts to secure nearly any phone while taking advantage of Qi wireless phone charging. All four arms feature rubber-coated caps that hold your phone firmly in place, and the open design keeps buttons and switches accessible on the sides of phones. To insert your device, simply squeeze the arms on one side of the cradle and place your phone inside before releasing the arms. This Qi wireless charging cradle ensures your compatible phone charges no matter what position it’s placed at. For added security and peace of mind, a device tether is included that’s recommended for outdoor applications. In addition, a support leg can be adjusted to the ideal position or removed altogether. This RAM® Tough-Charge™ with X-Grip® Technology wireless charging kit for vehicles includes a B size diamond base featuring a 1” rubber ball – perfect for attaching to your choice of B size RAM® double socket arm. The connected Type-A male pigtail connector features an in-line switch that allows you to turn off the wireless charging module when not in use. For in-vehicle charging, attach the pigtail to the included 1.2m Type-A male to Type-A female extension cable. Features: Waterproof Qi wireless phone charging cradle features spring-loaded RAM X-Grip technology Kit for vehicles includes wireless cradle, B size diamond ball base, and extension cable; attaches to B size double socket arms Made of powder-coated, marine-grade aluminum, stainless steel components, and high-strength composite for durability and reliability in the most demanding environments RAM Mounts backed by lifetime warranty, RAM electronics backed by 1-year warranty Specifications: Hardware Included: (1) Safety Tether, (1) Glue Tube for Rubber Caps, (1) Cradle Leg, (1) Cradle Leg Cover, (1) Silicon sleeve for USB waterproof connection, (1) 1.2 Meter USB Extension Cable  Holder Dimensions: Width Range: 2.375" - 3.25", Depth Range: .875" max  Ball/Socket Size: B Size (1")