1-1/2" Seacock with Curved Tail Piece This Perko seacock incorporates a polymer ball and seat, ensuring a tight seal, ease of operation, and drain plugs for winterizing.  Features: Handles are easily removed Cast bronze 90-degree curved hose adapter Includes thru-hull, hose adapter, drain plug, four pre-drilled mounting holes, and bonding screw Specifications: Hose Size: 1-1/2 in. Pipe Size: 1-1/2 in. Flange Diameter: 5-1/2 in. Overall Height: 8-3/8 in. Bolt Size: 3/8

Perko 2-1/2" Seacock Ball Valve Bronze These valve bodies are offered to meet the needs of applications that require extra long, scoop or flush type thru-hulls. Cast Bronze. Technical Information: Flange Diameter Inches: 7-1/4" Overall Height Inches: 7-1/2" Pipe Size Inches: 2-1/2" Model Number: 0805010PLB Ship Weight: 19.6 lbs. *Overall height is measured from the top of the hose adapter to the bottom of the flange.

Perko 1-1/2" Seacock Ball Valve Bronze These valve bodies are offered to meet the needs of applications that require extra long, scoop or flush type thru-hulls. Cast Bronze. Technical Information: Flange Diameter Inches: 5-1/2" Overall Height Inches: 4-1/2" Pipe Size Inches: 1-1/2" Model Number: 0805008PLB Ship Weight: 6.4 lbs. *Overall height is measured from the top of the hose adapter to the bottom of the flange.

Backing Block for 1-1/4" & 1-1/2" Seacocks Features: Each size fits multiple seacock sizes Press threaded brass inserts into the hull side of the backing block into the holes that match the seacock flange Rigid 1/2" thickness provides secure installation but is flexible enough to conform to minor hull curvature Will not swell or absorb moisture Made from an environmentally friendly PVC foam specially formulated for marine applications

Backing Block for 2" & 2-1/2" Seacocks Features: Each size fits multiple seacock sizes Press threaded brass inserts into the hull side of the backing block into the holes that match the seacock flange Rigid 1/2" thickness provides secure installation but is flexible enough to conform to minor hull curvature Will not swell or absorb moisture Made from an environmentally friendly PVC foam specially formulated for marine applications

Perko 1/2" IPS Intake Strainer Bronze PERKO Intake Strainer are designed for easy installation and cleaning. Features include mounting lugs cast into both sides to assure universal mounting, four outside tie rods and a 316 stainless steel strainer basket to minimize electrolysis. Screen hole diameter .077 inches, 46% open area. Hinged lugs for the cast bronze cover permit easy removal and cleaning of the strainer basket. A drain plug in the bottom casting is provided for easily removing sediment and draining for winterizing. Cast bronze. Please note: Spare parts for this item are NOT interchangeable with the Perko 0593 Flushing Strainer. Technical Information: Pipe Size Inches: 1/2 Height Overall Inches: 5-3/4 Width Overall Inches: 4-1/2 Model Number: 0493004PLB Dimensions Cylinder Inches: 3-1/2 x 4 Dimensions Basket Inches: 1-13/16 x 4-3/8 Open Area to Pipe Size Ratio: 30.1 Ship Weight: 4.9 Spare Gasket Kit: 0493DP599M (or) 99R Made in the USA

Perko 1/2" Thru-Hull Fitting w/ Pipe Thread Bronze Flange is machined to fit hull and grooved to retain bedding compound. Neck is threaded to approximately 3/8 inch from flange. Cast bronze. Technical Information: Pipe Size Inches: 1/2 Mouting Hole Diameter Inches: 13/16 Maximum Hull Thickness Inches: 1-3/8 O.D. Flange Inches: 1-1/2 Model Number: 0322DP4PLB Ship Weight: 1.8/7.9 lbs. MADE IN THE USA

Perko 1/2" Thru-Hull Fitting f/ Hose Plastic Molded White Plastic Broad Flange Technical Information: Hose Size Inches: 1/2 Mounting Hole Diameter Inches: 13/16 Maximum Hull Thickness Inches: 1-1/4 O.D. Flange Inches: 1-1/2 Model Number: 0328DP4 Ship Weight: 1.0/5.8 lbs. MADE IN THE USA

Perko 1/2" Intake Strainer Bronze Cast bronze Machined Slots Technical Information: Maximum Pipe Size Inches: 1/2 Maximum Hull Thickness Inches: 2-1/4 Dimensions Strainer Inches: 3 x 4 Model Number: 0065DP4PLB Ship Weight: 3.8/7.3 Screw Size: #8 Spare Flanged Nut: 0075

March TE-7S-MD 1.5hp 3 phase March Pump's industrial TE-7S-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 53 gallons per minute at 10 feet, and its maximum head is 57.5 Feet (or around 25PSI). The standard wet end (the materials that come into contact with the solution) is composed of 316 Stainless Steel, Viton, Carbon, and Ceramic. The inlet connection is 1-1/2 inch female pipe thread, and the outlet is 1 inch male pipe thread. There are two standard motors. The first is a 1 Phase 60 hertz 115/208/230V and 50 hertz 110/220V 1 horsepower totally enclosed fan cooled motor.  The second is a 3 Phase 60 hertz 208/230/460V and 50 hertz 190/380V 1 horsepower totally enclosed fan cooled motor. There are performance differences between the hertz options. The maximum internal pressure the pump can tolerate is 200PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius. The March TE-7S-MD centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents. To determine if the March TE-7S-MD is suitable for your application, please contact March Pump.   Perfect for Applications Including; Applications for the TE-7S-MD Magnetic Drive Pump include chemical recirculation, chemical transfer, refrigerators, scrubber systems, detergent mixers, computer cooling, carbon arc furnace cooling, silver recovery systems, and marine air conditioners.   Great for Chemicals Including The TE-7S-MD has pumped Acetic Acid, Citric Acid, Ethylene Glycol, Formaldehyde, Potassium Chloride, Potassium Hydroxide, Sodium Chloride,  Sodium Hydroxide (Caustic Soda), Fresh Water, Salt Water, and many more chemicals.     Unit 60HZ 50HZ System US Metric US Metric Max Flow 53 GPM 200 LPM 47.5 GPM 180 LPM Max Head 57.5 FT 17.5 M 39.4 FT 12 M Power 1 HP .745 KW 1 HP .745 KW Electrical 1PH 115/208/230V 60HZ, 110/220V 50HZ or 3PH 208/230/460V 60HZ, 190/380V 50HZ On 50HZ, the Single Phase Motor is rated for 1 horsepower or 0.7457 kilowatts. On 50HZ, the Three Phase Motor is rated for 1 horsepower or 0.7457 kilowatts.     Type Centrifugal Mag Drive Inlet 1-1/2"FPT Outlet 1"MPT Wet End 316 Stainless Steel (Front Housing, Rear Housing, Impeller), Viton (O-Ring), Ceramic (Shaft, Thrust Washers), Carbon (Bushing) Motor Options Available in 1HP, 1.5HP, 1HP Explosion Proof or 1.5HP Explosion Proof P/N 0155-0173-0300 (1 Phase 1HP) with Metal Motor Bracket P/N 0155-0174-0300 (3 Phase 1HP) with Metal Motor Bracket P/N 0155-0036-0300 (3 Phase 1.5HP) with Metal Motor Bracket P/N 0155-0285-0100 (1 Phase 1HP) with Plastic Motor Bracket P/N 0155-0286-0100 (3 Phase 1HP) with Plastic Motor Bracket P/N 0155-0287-0100 (3 Phase 1.5HP) with Plastic Motor Bracket  

Heat Shrink Tubing 1/2" x 6" - Red - 5 Pieces Package of 5 Red 6 in (15.2 cm) long sections with a 1/2 in (12.7 mm) diameter that shrinks to 5/32 in (4 mm). Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257 deg F / 125 deg C Operating temperature range of -40 deg C to 110 deg C UL 224 WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Premium Anchor Rode 215' - 15' of 1/4" Chain & 200' of 1/2" Rope w/Shackle This Premium Lewmar 215' anchor rode kit features 15 feet' of windlass chain spliced to 200' of 8 Plait line. Features: Eight (8) Plait rope is woven together with eight (8) individual braided strands. Outperforms the 3-strand once it is wet and used. Technical Specifications: Total Length - 215' Chain Length - 15' Chain Size - 1/4" Chain Type - G4 Rope Length - 200' Rope Size - 1/2" Rope Type - Eight (8) Plait Shackle - Not included *Sold as an Individual 

Ampco Pumps P1GXPIP-1/2 Plastic Cap Plug

Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0100 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents.     Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ     230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0100

Applications for the March AC-1A-MD-1/2 Magnetic Drive Pump include chemical transfer, photographic processing equipment, refrigeration systems, and water displays.   The AC-1A-MD-1/2 Part # 0115-0064-0200 has pumped Acetone, Ammonium Chloride, Ammonium Chloride, Ammonium Hydroxide, Citric Acid, Ethylene Glycol, Magnesium Nitrate, Potassium Carbonate, Sodium Borate, Fresh Water, Salt Water, and many more chemicals.  The AC-1A-MD-1/2 may have been modified to handle these chemicals.    March Pump's industrial AC-1A-MD-1/2 is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation and chemical transfer. It is capable of generating a maximum flow of 3 gallons per minute at 0.25 feet, and its maximum head is 4.6 Feet (or around 2PSI). The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Nylon, Carbon/Teflon, Stainless Steel, and Ceramic Magnet. The inlet connection is 0.5 inch smooth, and the outlet is 0.5 inch smooth. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on 60 hertz on 115V or 50 and 60 hertz on 230V (there are performance differences between the hertz options).  The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius. The March AC-1A-MD-1/2 centrifugal magnetic drive pump is capable of handling mildly or highly corrosive chemicals, acids, and solvents. To determine if the March AC-1A-MD-1/2 is suitable for your application, please contact March Pump.      Unit System 60Hz 50Hz Max Flow 3 GPM 9 LPM Max Head 4.6 FT 1 M Power .005 HP .003 KW Electrical 115V 60HZ       230V 50/60HZ   Type Centrifugal Mag Drive Inlet 1/2"OD Outlet 1/2"OD Wet End Polypropylene (Front and Rear Housing), Buna N (O-Ring), Nylon (Impeller), Carbon/Teflon (Thrust Washer), 316 Stainless Steel (Shaft), Ceramic Magnet   Part # 0115-0064-0200