Replacement Bracket for WL-1 Floating Strobe LED Waterlight Features: Replacement Bracket Specifically for WL-1 Floating Strobe LED Waterlight

WL-1 Floating Strobe LED Water Light Floating Man Overboard Strobe LED Light/Buoy Light Recent intense technological developments in the camera industry enable Forespar® to bring you this advanced LED strobe light at a significantly lower price. Powerful LED strobe, operates with spring post 6V lantern battery, comes with bracket mount, USCG approved. Built to meet Code of Federal Regulations sub part 161.010; this rugged LED water light produces brilliant strobe flashes automatically when thrown overboard and is visible for miles at sea. When used with a 6 volt alkaline lantern battery (not included) it will flash at the U.S.C.G. required rate for over 52 hours and will still flash at least every 2 seconds after 7 days of continuous operation (meets U.S.C.G. requirements – 46 CFR-161-010). A stainless steel molding bracket is included. Dimensions are 11-1/2” long, and 4” maximum diameter.

keywords: Golight, golight led lights, led lighting, led spotlight, led searchlight

Bosworth 400-H-Ale-1/2"F Guzzler 1/2" Hand Pmp,Tappd   Bosworth Hand Diaphragm Pump Guzzler Delrin, .44Qt per Stroke, 1/2" Female Threaded Ports, Buna Flapper Valves and Diaphragm, Horizontal Handle with Epoxy Coated Aluminum Clamp Ring for Durability

The Coast Guard's Seventh District has received at least three reports in the past few months regarding unapproved replacements of 406 EPIRB batteries by servicing companies having no association with the EPIRB manufacturer.  These unauthorized battery installations would likely result in a failure of this critical item of lifesaving equipment, and as such are not in compliance with the operational readiness requirements of 46 CFR. The following is a typical excerpt from an EPIRB manufacturer report: "The unit was opened and a foreign battery was found inside.  The battery was built up using (manufacturer) fuses and wiring salvaged from the original (manufacturer) battery.  They then covered their battery with the original (manufacturer) yellow heat shrink, (manufacturer) labels and taped it together.  This was then covered with a black heat shrink wrap.  The connections were soldered and not spot welded, as is required by the design and is performed in (manufacturer) production.  The battery measured 8.7 volts.  Our batteries read 9+ volts when they are new.  This battery was installed one week prior to it being brought into (manufacturer). There was also evidence of water intrusion due to the crack in the top cap, which (servicing company) did not recognize as they are not trained in these matters. The EPIRB was condemned by (manufacturer) and the customer was notified when he came to pick the unit up." Every approved (i.e., accepted by the FCC) EPIRB is tested during its approval process using a battery, or batteries, specified by the manufacturer.  Approved EPIRBs come with a user's manual which describes battery maintenance and replacement procedures.  In order for the EPIRB to remain within the conditions of its approval, the manufacturer's instructions in the user's manual must be adhered to.  To ensure that replacement batteries are of the same type with which the EPIRB was approved, and are correctly installed, manufacturers typically specify that battery replacements only be done by the manufacturer or a manufacturer-approved shop. Any modification or changes to an EPIRP must be made in accordance with the manufacturer.  The use of alternative replacement parts or batteries is prohibited and may prevent the device from meeting lifesaving requirements.  The Coast Guard strongly reminds EPIRB owners and servicing facilities to be aware of the compliance implications and potential for equipment failure stemming from any EPIRB modification or unauthorized battery replacement. This safety alert is provided for informational purposes only and does not relieve any domestic or international safety, operational or material requirement.  Questions regarding the information presented in this alert may be addressed to LCDR Vince Gamma of the U.S. Coast Guard Headquarters Lifesaving & Fire Safety Standards Division at 202.372.1396 or Vincent.A.Gamma at uscg.mil.

Pro Series 3.0 Double Row 30" LED Light Bar - Combo Optics - Black Housing The 30'' Double Row Series is for users who want a painfully bright LED bar that won't break the bank. This light is perfect for mounting on a lower bumper, behind the grill, or across the top of an ATV and can throw a beam that will illuminate a whole air strip. Don't underestimate it's size.  At almost a meter long, Black Oak's 30" LED light bar has two rows of blindingly bright Osram 5W white LEDs (60 LEDs in total). Equipped with spot, flood and Combination beam pattern, this light bar will light up objects hundreds of yards ahead of a vehicle as well as objects in a vehicle’s blind spots with equal effectiveness, making it perfectly suited for every driving scenario. In order to take all the punishment that an off-road outing can throw, this 30" LED light bar is made using the most durable materials and proven manufacturing processes available today. Through this painstaking construction, this light was able to achieve a security rating of IP69K as well as pass US military standards. Black Oak's 30-inch light bar is completely waterproof, corrosion-resistant, and has an average lifespan of 50,000 hours of continuous use. All said, the 30" LED light bar is almost guaranteed to outlast the vehicle it is mounted on and is backed by Black Oak's limited lifetime warranty and money-back guarantee. Black Oak has taken the LED game to the next level. The Pro Series 3.0 features top-of-the-line LED tech, boasting a 20% increase in lumens, making this series of lights one of the brightest on the market. Features: 360° Ceramic Protection against UV, Salt Water & Corrosion 2 Stage Hydrex Seal Lock for IP69 protection and a fully submersible light bar Heavy-duty Dynamax housing for a 4x stronger frame Premium Dupont powder-coating for the highest quality and most resistant finish Combination Flood/Spot light pattern offers a superior lighting pattern Multi-mount brackets made of 9 gauge marine grade Stainless Steel Lens cover made of Lexan with a UV protectant Activities & Uses:  Off-Road combo light T-Top boat light Behind the grill light bar UTV trail riding Grill guard truck lights Technical Specifications: Total Wattage: 300W Amp. Draw: 12.7 LED Quantity: 60 Weight: 10.8 lbs. Raw Lumens: 39,600 Warranty: Lifetime IP Rating: IP69K     Connection: Deutsch connector Dimensions with Mounting Bracket (Width x Height): 31.4" x 4.125" In the Box: Light bar Complete wiring harness with fuse, relay, and switch 12 gauge wire Mounting brackets All hardware is ready to install! *Sold as an Individual

Tri-Color/Anchor/Strobe LED Navigation Light Lunasea's Tri-color/Anchor/Strobe LED navigation model has the added features that you asked for, and more. This lightweight fixture, made of machined aluminum weighs just 140 grams (4.9 ounces). We've added emergency strobe, auto daylight turnoff for anchor, and a removable bird spike. The waterproof connector is only 0.38 inch wide for easier cable routing. The glass lens assures excellent light transmission for the life off the product. This fixture produces NO EMI and utilizes Active Current Control technology. The masthead lamp eliminates all high frequency noise without compromising optical capability or mechanical and electrical specification.And last but not least, we hard anodized the unit to withstand harsh saltwater environments. Features: Anodized Machined Aluminum Ultra-light Weight, only 4.9 Ounces Miniature Waterproof Connector Glass Lens Maintains Full Brightness as low as 10VDC Three Wire Hookup Removable Anti-Bird Spike Specifications: Voltage Range: 12VDC Power Consumption: 4 Watt Light Output: 2NM Enclosure: Machined Aluminum - Removable Aluminum Bird-Spike Wiring: 3 Wire

Tilt & Swivel Lockable LED TV Wall Mount Bracket The Majestic BKT100 Tilt and Swivel Lockable LED TV Wall Mount Bracket is a unique bracket with a simple but very versatile design. The team at Majestic worked very closely with various Marine and RV manufacturers and customers to engineer a bracket that can be a simple wall bracket and yet give you the flexibility of some angular movement. The Majestic BKT100 Tilt and Swivel Lockable LED TV Wall Mount Bracket does just that is easy to install, and has a lot of flexibility. The Majestic BKT100 Tilt and Swivel Lockable LED TV Wall Mount Bracket comes in Black and will fit all Majestic LED TV models 22" or less. It is designed for easy mounting and removal. Simply remove the securing locking screw and slide up to remove or slide down to install. This bracket is designed for both 75mm and 100mm Vesa mounting solutions. The Tilt and Swivel allow for the TV to be installed almost anywhere and with the wide viewing angles, you will always see the perfect picture. Features Distance to wall: 44mm Loading weight: 15kgs Max TV size range: 15-22" Adjustable angle: 15 degrees up/down & left/right

P12 Battery Charger LED Remote LED Indicators Charging LED- Quick check for green light confirms charging Charge Stage- Displays charging stage Equalize LED- Indicates the charger is currently in equalization mode Fan Mode- Indicates charger's internal fan mode Charge Output- Displays the percentage of output current for each battery. Will also indicate maximum output setting when maximum output is adjusted to accommodate for AC source limitations Alert- Icon LEDs provide warning and alert status for quick diagnostics Four Control Buttons Fan- User adjustable settings Dim/ Alarm- Provides adjustment to brightness of LEDs on display as well as Silence function for alarms Output- User adjustable charger output when AC source limitations exist that require lowering the AC current draw Power- Places P12 Battery Charger into standby mode WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Replacement Transducer Bracket for Plastic Transom Mount Transducer with Depth & Temp This replacement Transducer Bracket is for the plastic transom mount that can be used to replace the dual frequency transducers included with many Garmin units. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MR11 LED Light Time to lose those heat producing energy hungry MR11s and replace them with cool running low energy LEDs. Super Bright - Low Energy General purpose and reading light Wide 120° viewing angle Super Bright Up to 50,000 Hours 10V-30VDC / 12V AC

FBRS 2897 Battery Replacement Service for PLB-300 ResQFix ACR Life Safety equipment batteries should be replaced according to the manufacturers recommendation and instructions to ensure proper functionality. Battery replacement service includes - Complete physical integrity check Pressure test Data transmission test Replacement of seal and o-rings Installation of the new battery  Disposal of the old battery. *Sold as a Service This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

FBRS 2898 Battery Replacement Service for PLB-300 MicroFix ACR Life Safety equipment batteries should be replaced according to the manufacturers recommendation and instructions to ensure proper functionality. Battery replacement service includes - Complete physical integrity check Pressure test Data transmission test Replacement of seal and o-rings Installation of the new battery  Disposal of the old battery. *Sold as a Service This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

FBRS 2882 Battery Replacement Service for PLB-350 AquaLink™ ACR Life Safety equipment batteries should be replaced according to the manufacturers recommendation and instructions to ensure proper functionality. Battery replacement service includes - Complete physical integrity check Pressure test Data transmission test Replacement of seal and o-rings Installation of the new battery  Disposal of the old battery. *Sold as a Service This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

FBRS 2883 Battery Replacement Service for PLB-350 B SARLink™ ACR Life Safety equipment batteries should be replaced according to the manufacturers recommendation and instructions to ensure proper functionality. Battery replacement service includes - Complete physical integrity check Pressure test Data transmission test Replacement of seal and o-rings Installation of the new battery  Disposal of the old battery. *Sold as a Service This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.