|
Our P79 in-hull transducer easily adjusts to hull deadrise angles up to
22'. This ensures that the beam is vertically oriented to receive echos resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance.
Works with the Lowrance HDS Series and Simrad NSE Series Multifuction Display units.
Features
Depth
50/200 kHz
600 W RMS
Mid-performance
Plastic
7 Pin Blue Connector
|
174.35 |
|
|
P79 In-Hull Transducer w/Humminbird #9 Plug - 7-Pin
Our P79 in-hull transducer easily adjusts to hull dead rise angles up to 22º. This ensures that the beam is vertically oriented to receive echoes, resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance.
Features:
Adjusts to hull deadrise angles from 2° to 22°
No holes to drill
Depth only
Recommended for solid fiberglass hulls
Adheres to aluminum hulls under 3.8 mm (0.16") thick
Recommended for planing-hull power boats, trailered boats, rigid inflatable boats (RIBS), and racing sailboats
No hull protrusions
Boat Size: Up to 8M (25')
Specifications:
Weight: 2.3kg (5lb)
Hull Deadrise: 0° to 22°
Acoustic Window: Layered plastic urethane
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
168.41 |
|
|
xSonic P79 Adjustable 200/50kHz Plastic In-Hull Transducer - 9-Pin
This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap.
The 9-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise.
Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat.
*Fiberglass should be no more than 5/8" thick
*Not recommended for cored hulls
|
122.22 |
|
|
P79 NMEA 2000 In-Hull 235 kHz
The P79 in-hull transducer easily adjusts to hull deadrise angles up to 22 °. This ensures that the beam is vertically oriented to receive echos, resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance.
The unique adjustable-angle design ensures the beam is vertically oriented for maximum echo returns and the best possible performance. Because the transducer is mounted inside the hull, it is the perfect solution for rigid inflatable boats (RIBS) and racing sailboats.
Features:
Adjusts to hull deadrise angles up to 22°
No holes to drill
Depth Only
Frequency: 235 kHz
Cone: 11°
Recommended for solid fiberglass hulls
Epoxies to aluminum hulls under 0.38 mm (0.150”) thick
Recommended for planing-hull power boats, trailered boats, rigid inflatable boats
No hull protrusions
6M (20’) NMEA 2000® cable & connector
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
373.09 |
|
|
Adjustable In-Hull Transducer
600 Watt adjustable angled in hull transducer. (P79)
Compatible with the following Echo Sounders:
SL Series: SL755RC, SL760RC , SL1250, and SL1250RC
hsb2 Plus Series: L755RC, L760, L760RC, L1250,and L1250RC
hsb2 HDFI Series: DSM250, L770D, L770DRC, L1260D, and L1260DRC
Compatible hull material: fiberglass
Max Power: 600 W
Frequency: 200/50 kHz
Beam Angles: 200 kHz 11 50 kHz 45
Features:
Depth only.
Can be used in conjunction with the E66019 ST69 speed and temperature sensor
Easily adjusts to any deadrise angle up to 22
Transmits sound waves directly at the bottom so strong echoes are reflected back to the transducer
Can be removed in seconds for servicing or storage
Only the base piece is bonded to the hull. There is no adhesive layer under the transducer face to absorb sound energy
Simplifies in-hull installation
30ft (10m) Cable
|
209.98 |
|
|
P79 Adjustable In Hull Transducer 50/200kHz with 6-Pin
Features:
In Hull Transducer
Plastic
Adjustable
6-Pin
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
168.41 |
|
|
P79 In-hull
Our P79 in-hull transducer easily adjusts to hull deadrise angles up to 22°. This ensures that the beam is vertically oriented to receive echos resulting in accurate depth readings. Unlike traditional "puck" type transducers, our P79 consists of a base that is bonded to the hull and filled with liquid. The separate transducer then attaches to the base with a twist lock. The sound waves travel more efficiently though the liquid, giving the best possible performance.
Features:
Depth
200 kHz
600w RMS
Mid-performance
Plastic
|
219.98 |
|
|
Airmar P79 Adjustable 200/50kHz Plastic In-hull Transducer (8-pin)
010-10327-20
This entry level in-hull transducer with an adjustable deadrise angle makes installation a snap.
The 8-pin 600 W transducer has a depth of 800 to 1,200 ft; an operating frequency of 50 to 200 kHz; a beamwidth of 45 to 12 degrees; and a 0 to 22 degree deadrise.
Transducer kit comes with installation instructions*. Follow the instructions carefully to avoid damaging your boat.
*Fiberglass should be no more than 5/8" thick. Not recommended for cored hulls.
When using with a 6-pin Garmin sounder, transducer adapter cable part number 010-11612-00 is required.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
168.41 |
|
|
Adjustable In-Hull Transducer
This in-hull transducer has a patented adjustable feature which ensures that sound waves are transmitted vertically to the bottom on almost any hull with a deadrise up to 22°.
With no hull penetration, installation is easy and high speed performance is maximized.
Specifications:
30" (10 Meter) Cable included
Adjusts to Hull Deadrise Angles from 2° to 22°
2-pin Packard connector (CN0068)
Depth only
Boat Size: Up to 8 m (25’)
Epoxies to aluminum hulls under 3.8 mm (0.125”) thick
Factory P/N SN2010 and AirMar® P/N 31-247-1-01 (Model P79)
**Sold as an Individual
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
143.99 |
|
|
P79, In-Hull Mount Smart Transducer, NMEA 2000
Our in-hull mount smart transducer provides depth data to your NMEA 2000® network. This transducer has an operating frequency of 235 kHz and a beamwidth of 11°. It accommodates deadrise angles of up to 22°.
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
310.79 |
|
|
Active Imaging 2-in-1 Transducer & 83/200 Pod In-Hull Transducer with Y-Cable
Allows for connection of an in-hull puck transducer and an Active Imaging 2-in-1 (Side/Down) transducer to the single sonar port of an Elite Ti2 or Elite FS display.
Features:
Active Imaging 2-in-1 Transom Transducer
83/200 Pod/Puck Transducer without temperature
Dual 9-pin Y-cable
|
289.30 |
|
|
P79 Plastic In-Hull Transducer, 600w (10-Pin)
600 Watts
50/200 kHz
45/15 degree Beam Angles
Plastic In-Hull Mount for Shoot-Through Applications
30 Foot Cable with 10-Pin Connector
WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
218.18 |
|
|
xSonic M135M Medium Chirp 1 kW In-Hull Transducer - 9-Pin
The M135M’s medium frequency delivers the right combination of coverage under the boat, an extended depth range, and the ability to produce clean and accurate target and structure returns in mid- to deeper water. Medium frequency also delivers excellent shallow to mid-depth performance, bottom detail, and fish-target separation. Operating at a frequency range of 85 to 135 kHz, this transducer reveals fish at medium depths up to 457 m (1500 ft) and gives ultra-clear target resolution.
Airmar’s M135M includes a plastic mounting base that is aligned with the centerline and secured inside the hull. Then it is filled with non-toxic antifreeze. The transducer is inserted into the base and adjusted for the proper deadrise offset, ensuring the beam is shooting straight down for maximum echo returns. The eco-friendly coolant is the best medium to transmit through solid fiberglass and into the surrounding water. The major benefit of an in-hull transducer is that there are no protruding features on the exterior of the hull, making it the perfect choice for trailered or lifted boats. Designed for smaller boats up to 11 m (36') with a solid fiberglass hull.
Features:
Depth only
1 kW of power
50 kHz of total bandwidth from one transducer
Recommended for use on planing and displacement hulls
Plastic transducer and mounting base
Covers popular fishing frequencies of 88 and 107 kHz plus everything else in the bandwidth
Also available as transom (TM185M), thru-hull low-profile (B175M), and thru-hull with fairing (B285M) mounts
Patented Xducer ID® technology
Specifications:
Medium frequency: 85 to 135 kHz
Beamwidth: 16 degrees to 11 degrees
Maximum Depth: 457 m (1500 ft.)
Weight: 4.2 kg (9.2 lb.)
Recommended Boat Length: Up to 11 m (36 ft.)
Hull Material: Solid fiberglass only
Hull Deadrise: Up to 22 degrees
Acoustic Window: Urethane
Transducer Element: One broadband ceramic assembly
Includes: Adjustable mounting base
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
809.66 |
|
|
Kronos 2" Depth Sounder with In-Hull Transducer
Polished Stainless Steel Bezel, flat glass lens, Perimeter lighted spun Aluminum dial with Gold and Black graphics.
The Depth Sounders from Faria offer a 3-199 foot (1-61meters) depth capability, with an automatic gain control, backlighting for maximum night vision, keel offset, and deep and shallow water alarms.
Depth can be read in meters, and feet. With its oversized back-lit display depth can be easily read in any condition. Audible and Visual alarms let the boater know when a shallow or deep water condition exists.
Depth Sounder includes a Faria SN2010 In-Hull Transducer w/20' cable.
2" - Hole Size: 2.0625" (53mm)
Specifications:
Imperial and Metric Values
199 Foot (61m) Depth Capability
Programmable Keel Offest
Audible and Visual alarm for Shallow/Deep Water Conditions
Flat Glass Anti-fog, Scratch Resistant Lens
Stainless Steel Bezel
Factory P/N DS0131
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
266.69 |
|
|
Chesapeake White SS 2" Depth Sounder with In-Hull Transducer
Perimeter-lighted White dial with stylish Blue and White graphics, polished stainless steel bezel and domed glass lens.
The Depth Sounders from Faria offer a 3-199 foot (1-61meters) depth capability, with an automatic gain control, backlighting for maximum night vision, keel offset, and deep and shallow water alarms.
Depth can be read in meters, and feet. With its oversized back-lit display depth can be easily read in any condition. Audible and Visual alarms let the boater know when a shallow or deep water condition exists.
Depth Sounder includes a Faria SN2010 In-Hull Transducer w/20' cable.
2" - Hole Size: 2.0625" (53mm)
Specifications:
Imperial and Metric Values
199 Foot (61m) Depth Capability
Programmable Keel Offest
Audible and Visual alarm for Shallow/Deep Water Conditions
Domed Glass Anti-fog, Scratch Resistant Lens
Stainless Steel Bezel
Factory P/N DS0110
*Sold as an Individual
**Gauge Cover not Included
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
208.09 |
|