Stanchion Kit SK135 - For All SailPods & Most SystemPods Great for overhead mounting on Powerboats or extending the available dash space on the flybridge. Useful for unique mounting locations in the cockpit on Sailboats. Includes two 1.25" Stainless Steel tubes with 15° bends pre-drilled for mounting 9.5" or 12" SailPods or SystemPods on a flat surface (does not fit GP1500/GP2500 Series or GP1600/GP2600 Series SystemPods). Stanchion Kit includes: 1.25" diameter 316 stainless steel Mirror polished finish Pre-drilled mounting and wire access holes Stainless steel feet can be removed for adjusting the height *See Literature tab for an image with dimensions

Stanchion Kit Predrilled for GP1300, GP1400 Series InstrumentPods, GP1500, GP1600 & GP1040 Series SystemPods & GP1800 Series SailPods SK11 Stanchion Kit is used for mounting GP1300, GP1400 Series InstrumentPods, GP1500, GP1600 and GP1040 Series SystemPods and GP1800 Series SailPods. It measures 11″ inch high, 1.25″ diameter stainless steel tube, predrilled to accommodate above listed products. The SK11 Stanchion Kit can be combined with most InstrumentPods or SystemPods and some SailPods for a very strong and sturdy mounting system. Great for on dash mounting on Powerboats or extending the available dash space on the flybridge. Can be used for overhead mounting as well. However, if interest in overhead mounting see SK125, SK129, or SK130 Stanchion Kits. Useful for unique mounting locations in the cockpit on Sailboats. Two 1.25″ stainless steel strait tubes. Includes pair of round stainless steel feet. They are polished and predrilled to easily fit together with the NavPod. Wires can be routed down both tubes and are all concealed for a very clean installation. Navpod sold separately 

AG118 Pedestal Guard  Single Bend AngleGuard 9.5″ Wide by 1.25″ diameter for all SailPods and SystemPods. Features: 316 grade stainless steel 065 gauge wall thickness Mirror polished finish All 1.25” include stainless steel feet (1” does not include feet)

SK130 PowerPanel Stanchion Kit for GP1030 / GP1060 / GP1080 NavPod's SK130 Stanchion Kit is used for the mounting of all SailPods and most SystemPods. Great for overhead mounting on Powerboats or extending the available dash space on the flybridge. Useful for unique mounting locations in the cockpit on Sailboats. Stanchion Kit Includes: 1.25" diameter 316 stainless steel Mirror polished finish Pre-drilled mounting and wire access holes Stainless steel feet can be removed for adjusting the height

SK129 PowerPanel Stanchion Kit for GP1800 / GP1040 / GP1050 SK129 Stanchion Kit is used for the mounting of all SailPods and most SystemPods. Great for overhead mounting on Powerboats or extending the available dash space on the flybridge. Useful for unique mounting locations in the cockpit on Sailboats. Stanchion Kit Includes: 1.25" diameter 316 stainless steel Mirror polished finish Pre-drilled mounting and wire access holes Stainless steel feet can be removed for adjusting the height

Clamp-On Furling Line Stanchion Lead Block - 1" Ball Bearing Delrin™ ball bearing sheave allows for quick and easy furling line adjustment. Stainless steel cage and strap ensure durability.  Specifications: Stanchions 1" (25mm) in diameter 1-7/16" (37mm) Sheave Diameter Maximum 1/2" (12mm) line size Safe Working Load = 1000 lbs (450kg) 

Stainless Steel Feet for 1.25″ Diameter AngleGuards or Stanchion Kits (Rectangular Base) with Hardware Stainless Steel Feet Pair Kit — compatible with all 1.25″ diameter AngleGuards or Stanchion Kits. All 1.25″ diameter AngleGuards and Stanchion Kits come with a pair of feet (rectangular base for AngleGuards, round base for Stanchion Kits), so it is not necessary to purchase this kit if you are already purchasing a 1.25″ diameter AngleGuard or Stanchion Kit. This kit includes: 2 stainless steel feet 316-grade stainless steel Mirror polished finish Rectangular base with footprint dimensions of 3-1/4″ x 1-7/8″ Eight mounting screws (#14 x 1″ Phillips Oval Head) Allen wrench for included foot set screws

SWIVL-EZE Lock'N-Pin 3/4" Pedestal Kit 13" Post 7" x 7" Stainless Steel Base Plate Threaded Features: Includes 7" x 7" stainless steel threaded base plate, black E-coated seat mount and 13" high seat post The 3/4" system gives you outstanding economical performance Great for adding seating to fishing, pontoon or cruising boats Lock'N-Pin products meet ABYC Standard

Top Gun Rigging Kit w/Klickers Complete rigging packages that allow you to run One (1) lines on each rigger. this kit includes (2) exclusive Rupp single pulley shock cords, 50ft of white braided nylon halyard lines one pair of Rupp KLICKER release clips. (2) Nylon ball stops, (2) Strap Eyes, (4) Snap Swivels, (2) Swivels. This rigging kit is for small outriggers, 20' and under.

RailMount Pre-Cut for Raymarine Axiom 7 & Axiom+ 7 RailMount Pre-Cut for Raymarine Axiom 7 and Axiom+ 7 only NO SONAR—-NOT FOR AXIOM 7 DV or AXIOM 7 RV (Requires Part# R70561 Right Angled Cable) (Pre-Cut is for Surface Mount) (fits 1″ or 1.25″ tubing) RailMount NavPods are best used for mounting an autopilot control, sailing instrument, or small chartplotter onto an existing pedestal guard. Fits onto any 1″, 1.125″, or 1.25″ diameter tube. A Stainless Steel arm is used to mount the NavPod housing. The NavPod can rotate 180 degrees for easy viewing while sitting under the dodger on a rainy day. All wiring runs from the NavPod, down the center of the stainless steel arm (available space is 0.75″ inside the narrowest part of the arm, so keep this in mind for planning your cable run; most transducer cables will not fit through the arm), and into the pedestal guard. This application provides a clean and sturdy installation for electronics, without the replacement of the pedestal guard. RailMounts are designed for all popular standard-size instruments, as well as 7 and 9-inch chartplotters. Structural Rigidity – The Gen3 enhancements now include a thicker gauge acrylic capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening and more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All RailMount NavPods are manufactured with a double gasket system providing an excellent watertight seal. This seal provides the best protection for your Marine Electronics. NavPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a “compression set” like many rubber compounds. This is important when you need to open the NavPod in the future in order to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – We use all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets for the NavPod wrench for better holding ability when tightening than screws used on our Traditional Series NavPod. The Nickel Chrome-Plated Stainless Steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – We stand behind our commitment by offering a 10-year warranty on all new Gen3 NavPods.

StarPod Kit for Starlink Roam/RV Antenna - Housing & Base The StarPod from NavPod is a waterproof housing designed for permanent mounting of the Starlink Roam/RV antenna, typically on a yacht’s hardtop or radar arch. The StarPod housing fits Starlink model UTA-212 (dish face measuring 20.2” x 11.9” / 513 mm x 303 mm). NavPod model SP212-K is the StarPod Kit, which includes the StarPod housing and a black powder-coated aluminum base. The included base is 8.25" tall with a 4" outer diameter and has a 6" circular footprint with four screw mounting holes. Third-Party Accessory Disclaimer: The NavPod and StarPod brands are in no way affiliated with the Starlink or SpaceX brands. The company's products are third-party accessories, distinct from the brands and products they are designed to house. What are the benefits of mounting a Starlink dish in a StarPod? StarPod protects Starlink and completely encloses the Starlink antenna in a very sturdy and attractive waterproof housing. Testing has proven that there is no degradation of signal inside the thermoformed acrylic-capped ABS housing. The Starlink Roam dish was originally designed for RVs, not boats. Its waterproof rating of IP54 is a long way from the IP67 rating NavPod is accustomed to in boating from the likes of Garmin, Raymarine, and others. Mounting a Starlink dish inside a StarPod provides additional protection from water intrusion, just as all NavPods have done for other marine electronics for over 25 years. How do I mount a Starlink dish inside a StarPod? The 4-legged "X" base that comes with a Starlink Roam dish is not utilized when mounting inside a StarPod; only the dish and attached mounting pole are used. The center post of the Starlink dish is inserted through the center hole in the bottom of the StarPod and extends into the chosen mounting pedestal. The initial Starlink setup process should be completed before mounting the dish inside a StarPod (refer to your Starlink setup and installation guide for this process). One important thing to note during the setup process is to make sure that the "Snow Melt" setting in the Starlink app is turned to "Off" (this feature produces excess heat to keep snow from piling up on a Starlink dish in winter environments, but is unnecessary and can potentially cause overheating when the dish is mounted inside a housing). Once the initial Starlink setup process is complete, the next step is to get the dish into a horizontal, or "flat" position, perpendicular to the mounting post. To get the dish into this position, unplug the Starlink dish, then plug it back in and turn it on. The dish will begin to move as part of its startup process, so just wait until it’s in a horizontal position and unplug the dish. This may take a couple of attempts, so just repeat as necessary until the dish is powered off in a horizontal or "flat" position. At this point, the dish can now be mounted inside the StarPod housing (using the instructions and hardware included with the StarPod). How can the Starlink dish move if it’s inside a StarPod? It can’t, but that’s okay. When powered on inside the StarPod housing, the Starlink dish will initially move as it looks for a signal. However, when the dish bumps into the inside of the housing and is unable to move any further, it will simply register an obstruction and discontinue its movement (a feature built into the dish to prevent the motor from burning out when it’s positioned next to a tree branch, ceiling, or other obstruction). The StarLink app may notify you of the obstruction, but the dish will continue to operate normally otherwise. There are several methods you can find on the internet for disabling your Starlink motor to achieve a fixed position. While these methods can be effective, it’s important to note that any modification of your Starlink antenna (drilling or cutting into the case, disconnecting internal cables, or any disassembly at all) will void the product warranty. If the Starlink dish can’t move, how can it get a good signal? Short Answer: A Starlink dish installed on a boat in a fixed horizontal position will achieve the same signal quality as a dish that’s free to move and adjust position. Long Answer: The Starlink Roam dish utilizes phased array technology. Rather than searching for a single satellite to point to (like older 18" and 24" satellite TV antennas), the Starlink dish is continuously switching between different satellites every few minutes (satellites that are moving at very high speeds and orbiting much lower than traditional TV and internet satellites). When a Starlink dish moves, it isn’t trying to point toward a particular satellite; it’s just looking for a clear view of the sky. Since this dish was originally designed for RV use, the movement of the dish was designed to allow it to point away from overhead obstructions like trees and buildings that might prevent a clear view of the sky. While this functionality makes sense for RV use, it is much less functional for boating use, where the dish would almost never encounter any overhead obstructions. When testing, a Starlink dish mounted and immobilized inside a StarPod achieved the same signal quality and internet speed as a dish that was free to move outside of a housing. Neither the fixed horizontal positioning nor the housing material itself resulted in any signal degradation as long as the dish had an otherwise clear view of the sky (as it typically would on a floating vessel). Liability Disclaimer: NavPod assumes no liability for any violation of Starlink product warranty or terms of service that may result from modifying a Starlink dish or mounting it inside a StarPod. General Information: StarPod is manufactured by Ocean Equipment in Bend, Oregon, USA, using the same time-proven materials that are used to fabricate the popular line of NavPods, waterproof housings for marine electronics. All NavPods Feature: Structural Rigidity – The Gen3 enhancements now include a thicker gauge of acrylic-capped ABS material that improves strength and provides better structural rigidity. This thicker material allows for a larger waterproof seal. The better the structural rigidity, the less flexing when tightening, and the more uniform pressure on the seal. The excellent UV stability of the acrylic is combined with the durability of the ABS. The acrylic cap protects the ABS from UV and its potentially damaging effects on plastic. Waterproof Seal – All NavPods are manufactured with a double gasket system, providing an excellent watertight seal. This seal provides the best protection for your marine electronics. StarPods are made to withstand the harshest wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with an improved flush fit. The internal Poron Microcell Polyurethane gasket is now 50% thicker and is not subject to a "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics. The gasket will continue to do its job. Nickel Chrome-Plated Stainless Steel – The company uses all 316 stainless steel hardware that is supplied with each NavPod. Large round-head tamper-resistant screws have deeper sockets to match the NavPod wrench for better holding ability when tightening. The nickel-chrome-plated stainless steel tamper-resistant screws provide security combined with a little style! Commitment to Quality – Navpod stands behind its commitment by offering a 10-year warranty on all new NavPods, including the StarPod.

Hypro 9910-Kit2445 Kit Valve Repair This repair kit is for the following pump models:   DBA110, DBS110, DBA140, DBS140   9910-KIT2445 Includes:   Qty 6 9910-680070 O-Ring   Qty 6 9910-759051 Complete valve   (Image does not represent exact kit contents)

Revolution Top Gun Package - 18' Buy Rupp's complete Outrigger System and save money. The Rupp Sportfishing kits make it simple to have your boat ready to fish upon receipt! If your boat came "outrigger ready" with a Rupp outrigger mounting plate or similar plate from TACO or E-TEC Marine - your ready to bolt in a Rupp Outrigger and go. This package comes complete with a pair of Revolution Bolt-In Top Gun Radial bases, a pair of 18' Telescoping poles and a complete single line rigging kit with Rupp release clips. Top Gun Telescoping Poles - 18' Pair Our 18 foot telescoping pole is comprised of three sections making it the most rigid and durable telescoping pole on the market. Very little flex and robust buttons make Rupp telescoping poles an obvious choice. Our telescoping poles are an ideal match for any of our Top Gun outrigger bases. Every part of these telescoping poles are fully serviceable, easy replaceable and made in the USA. O.D of outrigger base tube is 1.50", designed to fit perfectly into Rupp outrigger bases. Top Gun Rigging Kit w/Klickers Complete rigging packages that allow you to run One (1) lines on each rigger. this kit includes (2) exclusive Rupp single pulley shock cords, 50ft of white braided nylon halyard lines one pair of Rupp KLICKER release clips. (2) Nylon ball stops, (2) Strap Eyes, (4) Snap Swivels, (2) Swivels. This rigging kit is for small outriggers, 20' and under. Revolution Top Gun Bolt-In Outrigger Holders - Pair This innovative outrigger base is great for new installations or retrofits on both hard or soft tops. Rupp Revolution Top Gun bases reduce moving parts and offer an efficient and flexible BOLT-IN design that improves durability while reducing cost. Easily bolted into any 'outrigger ready' boat. A quarter turn of the handle disengages the handles locking pin for easy outrigger deployment. The only one of its kind, this product is constructed of aircraft grade anodized aluminum with stainless steel locking components. NO need to lift the outrigger weight for deployment. The outrigger locks itself into position upon retrieval. Rupp Revolutions are designed and manufactured 100% in the USA, utilizing proven materials and processes. All Rupp Top Guns come with a Three Year Warranty and Rupp's 'best-in-class' customer and technical service. Forged 4" x 6" mounting flange provides ease of BOLT-IN installation and below top operation. Designed to accept Rupp Top Gun Poles, either six piece fixed length or telescoping poles in 15' or 18'.

Z-30 Top Gun Outrigger Kit - 15' Buy Rupp's complete Outrigger System and save money. The Rupp Sportfishing kits make it simple to have your boat ready to fish upon receipt. If your boat came "outrigger ready" with a Rupp outrigger mounting plate or similar plate from TACO or E-TEC Marine - your ready to bolt in a Rupp Outrigger and go. This package comes complete with a pair of Z-30 Bolt-In Top Gun Radial bases, a pair of 15' Telescoping poles and a complete single line rigging kit with Klicker release clips. Top Gun Telescoping Poles - 15' Pair Our 15 foot telescoping pole is comprised of three sections making it the most rigid and durable telescoping pole on the market. Very little flex and robust buttons make Rupp telescoping poles an obvious choice. Our telescoping poles are an ideal match for any of our Top Gun outrigger bases. Every part of these telescoping poles are fully serviceable, easy replaceable and made in the USA. O.D of outrigger base tube is 1.50", designed to fit perfectly into Rupp outrigger bases. Top Gun Bolt-In Z-30 Bases - Pair An innovative advance in Top Gun engineering, Rupp's Z-30 gear drive system offers unmatched ease of operation for top mount outriggers. Simply turning the palm-size handle deploys and retrieves riggers smoothly and effortlessly with an outstanding 30 to 1 advantage. Z-30 Top Guns are engineered for durability with a high strength, forged aluminum body that protects cutting edge components. Now with anodized aluminum knob and other enhancements. Forged 4" x 6" mounting flange provides ease of BOLT-IN installation and below top operation. Designed to accept Rupp Top Gun poles in 15' or 18'. Top Gun Rigging Kit w/Klickers Complete rigging packages that allow you to run One (1) lines on each rigger. this kit includes (2) exclusive Rupp single pulley shock cords, 50ft of white braided nylon halyard lines one pair of Rupp KLICKER release clips. (2) Nylon ball stops, (2) Strap Eyes, (4) Snap Swivels, (2) Swivels. This rigging kit is for small outriggers, 20' and under.

Z-30 Top Gun Outrigger Kit - 18' Buy Rupp's complete Outrigger System and save money. The Rupp Sportfishing kits make it simple to have your boat ready to fish upon receipt. If your boat came "outrigger ready" with a Rupp outrigger mounting plate or similar plate from TACO or E-TEC Marine - your ready to bolt in a Rupp Outrigger and go. Top Gun Telescoping Poles - 18' Pair Our 18 foot telescoping pole is comprised of three sections making it the most rigid and durable telescoping pole on the market. Very little flex and robust buttons make Rupp telescoping poles an obvious choice. Our telescoping poles are an ideal match for any of our Top Gun outrigger bases. Every part of these telescoping poles are fully serviceable, easy replaceable and made in the USA. O.D of outrigger base tube is 1.50", designed to fit perfectly into Rupp outrigger bases. Top Gun Bolt-In Z-30 Bases - Pair An innovative advance in Top Gun engineering, Rupp's Z-30 gear drive system offers unmatched ease of operation for top mount outriggers. Simply turning the palm-size handle deploys and retrieves riggers smoothly and effortlessly with an outstanding 30 to 1 advantage. Z-30 Top Guns are engineered for durability with a high strength, forged aluminum body that protects cutting edge components. Now with anodized aluminum knob and other enhancements. Forged 4" x 6" mounting flange provides ease of BOLT-IN installation and below top operation. Designed to accept Rupp Top Gun poles in 15' or 18'. Top Gun Rigging Kit w/Klickers Complete rigging packages that allow you to run One (1) lines on each rigger. this kit includes (2) exclusive Rupp single pulley shock cords, 50ft of white braided nylon halyard lines one pair of Rupp KLICKER release clips. (2) Nylon ball stops, (2) Strap Eyes, (4) Snap Swivels, (2) Swivels. This rigging kit is for small outriggers, 20' and under.