13.25" Pre-Drilled Dual Mount for Most Closed Dome Radars - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Separately

23.75" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Separately

28" Pre-Drilled Dual Mount for Open Array Radars Up to 4.5' - Black - Top Plate Required Install your sat dome, camera, or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. The oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large number of space results in the perfect solution where space saving is a must.   Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for a cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or an open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount.   Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them.  *Top Plate Sold Seperately

12.5" Dual Mount for Most Radar Domes - Top for Sat Domes - Top Plate Required Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them. *Top Plate Sold Separately*

4-Degree Wedge for Most Closed Dome Radars - 18"-24" - Black Improve your radar performance with a Seaview direct mount Angled Wedge. This wedge angles your radar 4 degrees below the horizontal. Goes directly underneath your radar. Fits major brands such as Garmin, Raymarine, Simrad, Furuno & more! Features: Simple and Easy Installation Pre-drilled to fit your specific radar, allowing for quick and easy hassle-free installation.  Durable Made from marine-grade polymer Compatible Manufacturers: B & G Garmin Humminbird Koden Lowrance Raymarine Simrad

Modular Plate for Most Closed Dome and Open Array Radars Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics. Unique Design No longer the unwanted “swiss cheese” look with a Seaview modular top plate. These plates result in only 4 visible mounting screws to secure electronics. A anodized 1/4" thick aluminum plate is pre-drilled to fit most marine electronics. This aluminum plate is then encased in a UV stable glass filled ABS white plastic. Each top plate is dimpled to match the provided drill templates for easy and precise drilling for your specific marine electronics.

Modular Plate for Most Closed Domes & Open Arrays - Black Seaview Modular Top Plates are designed to be mounted onto Seaview Modular Mounts. These Top Plates eliminate the "swiss cheese" look of most other radar and satdome mounts. With Seaview Top Plates the result is only four visible mounting screws to secure electronics.  Unique Design No longer the unwanted “swiss cheese” look with a Seaview modular top plate. These plates result in only 4 visible mounting screws to secure electronics. A anodized 1/4" thick aluminum plate is pre-drilled to fit most marine electronics. This aluminum plate is then encased in a UV stable glass filled ABS white plastic. Each top plate is dimpled to match the provided drill templates for easy and precise drilling for your specific marine electronics. Note: This only applies to the ADA-R1, ADA-S1 & ADA-S2 Top Plates King Starboard The ADA-R2, ADA-S3, ADA-S4 & ADA-F1 Top Plates are made of King Starboard. It comes pre-marked and supplied with a drill template. The end result is a clean looking installation.

4-Degree Wedge for Most Closed Dome Radars - 18"-24" - White Improve your radar performance with a Seaview direct mount Angled Wedge. This wedge angles your radar 4 degrees below the horizontal. Goes directly underneath your radar. Fits major brands such as Garmin, Raymarine, Simrad, Furuno & more! Features: Simple and Easy Installation Pre-drilled to fit your specific radar, allowing for quick and easy hassle-free installation.  Durable Made from marine-grade polymer Compatible Manufacturers: B & G Garmin Humminbird Koden Lowrance Raymarine Simrad

The Vision Series Mounting System is a revolutionary design that provides the simplest, most attractive solutions to your electronics mounting requirements.  Dual Mount for a Radar Dome and a Satellite Dome. Two Mounting Plates required. Features: All-new sleek, modern design First all modular system - extremely versatile Simple selection and installation Easy to add accessories Two marine electronics mounting platforms Powder coated aluminum Requires Vision Mounting Plate to install radar or sat dome antenna 18" Sat Dome Dual Mount Aft raked 30 degrees 18" tall

The Vision Series Mounting System is a revolutionary design that provides the simplest, most attractive solutions to your electronics mounting requirements.  Dual Mount for a Radar Dome and a Satellite Dome. Two Mounting Plates required. Features: All-new sleek, modern design First all modular system - extremely versatile Simple selection and installation Easy to add accessories Two marine electronics mounting platforms Powder coated aluminum Requires Vision Mounting Plate to install radar or sat dome antenna 24" Sat Dome Dual Mount Aft raked 30 degrees 24" tall

22.5" Dual Mount for Up To 4.5' Open Array Radar - Top for Sat Domes - Top Plate Required  Install your satdome, camera or other marine electronics above your radar using a Seaview Dual Mount. Doing this ensures maximum performance out of your electronics and eliminates radar interference. The bottom mounting plate is pre-drilled to fit all closed dome radars, while the top mounting plate is modular and sold separately. Oval hollow mast section allows for easy cable management. Compact Design Specifically designed to not take up a large amount of space results in the perfect solution where space saving is a must. Eliminate Interference A Dual Mount gives your radar or satdome extra height clearance to tower above anything that could obstruct its view, while still maintaining a small footprint. This also allows for all electronic cables to pass through one hole for cleaner installation. Universal The lower platform is welded onto the main body of the mount. This platform comes pre-drilled for just about all open and closed dome radars. The above image shows a lower platform on a dual mount that’s for a closed dome radar. When selecting a Seaview dual mount be sure to check to make sure that the particular one you are looking at is for a closed dome radar or a open array radar. The dual mounts that are for an open array radar have an extended lower platform so that the antenna clears the main body of the mount. Modular Top Plate The top platform is where you bolt the Top Plate to. Seaview developed the Top Plate to make product selection easier for the customer and to enhance the look of these mounts. Long gone are the days of top plates with a bunch of holes in them. *Top Plate Sold Separately*

2" Diameter Compact Light Bar f/Thermal Cameras, Spotlights & Nav Light To Clear Closed Dome Radars *Must Pick an LTB TOP A compact 2” diameter light bar designed to fit Seaview modular mounts that will elevate most searchlights, thermal cameras with the universal plate, and a nav light above closed dome radars. This will clear 18-24" diameter closed dome radars with the exception of Raymarine RD424.  Works with Mounts ending in M1 or M2. * Will work for all FLIR models, WITH THE EXCEPTION OF THE FLIR M300C, M332, M364, M364C ** Will clear 18"-24" closed dome radars, WITH THE EXCEPTION OF THE RAYMARINE RD424

1-1/4" Light Bar for Closed Domes Requires LTB Top - Black Seaview light bars are made from aluminum and powder coated brilliant white and are compatible with Seaview Modular Mounts. These light bars are 1.25" in diameter. Different styles of light are available as well as numerous accessories for your light bar. Accessories such as LED anchor lights, GPS adapters, wind transducer adapters and etc. What's also unique with Seaview light bars is that they can fold over 90° to allow for extra height clearance. Many Styles There are many different styles of Seaview light bars so you can be sure to get one that will work with your specific application. Styles for closed dome radars, satellite domes, open array radars and cameras/search lights.  Extra Height Clearance On select Seaview light bar models some can fold over 90° to allow for extra height clearance. Simply loosen the four bolts around the stainless steel clamp and fold over in either direction. Only LTB-R, LTB-S and LTB-S24 can fold over.  Easy Installation Secured with a stainless steel clamp, simply use the supplied four bolts. This does not apply to the LTB-SF, LTB-OA and LTB-OA-6 light bars.

1-1/4" Light Bar for Closed Dome Radar - Requires LTB Top Seaview light bars are made from aluminum and powder coated brilliant white and are compatible with Seaview Modular Mounts (polished S.S. light bars also available). These light bars are 1.25" in diameter. Different styles of light are available as well as numerous accessories for your light bar. Accessories such as LED anchor lights, GPS adapters, wind transducer adapters, etc. What's also unique with Seaview light bars is that many can fold over 90° to allow for extra height clearance.  Many Styles There are many different styles of Seaview light bars so you can be sure to get one that will work with your specific application. Styles for closed dome radars, satellite domes, open array radars and cameras/search lights. Extra Height Clearance On select Seaview light bar models some can fold over 90° to allow for extra height clearance. Simply loosen the four bolts around the stainless steel clamp and fold over in either direction. Easy Installation Secured with a stainless steel clamp, simply use the supplied four bolts  

1-1/4" Black Light Bar for FLIR & Searchlights - Folds Over 90° - Must Pick LTB Top Seaview light bars are made from aluminum and powder-coated brilliant white and are compatible with Seaview Modular Mounts (polished S.S. light bars are also available). These light bars are 1.25" in diameter. Different styles of light are available as well as numerous accessories for your light bar. Accessories such as LED anchor lights, GPS adapters, wind transducer adapters, etc. What's also unique with Seaview light bars is that many can fold over 90° to allow for extra height clearance  Many Styles There are many different styles of Seaview light bars so you can be sure to get one that will work with your specific application. Styles for closed dome radars, satellite domes, open array radars, and cameras/searchlights. Easy Installation Secured with a stainless steel clamp, simply use the supplied four bolts.