RAM Universal Finger Grip Holder Handlebar Rail Mount Part #: RAM-B-149Z-UN4U Motorcycle Handlebar Mount Description: The motorcycle mount makes attaching to handlebars, tubing, or railing a breeze. Simple to install and easy to use, the possibilities become endless. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM?s patented design also dampens shock and vibration helping to extend the life of your mobile device. Included in this package is hardware for tubing that is 0.50" to 1.25" in diameter. Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. The spine plate contains the universal AMPs and 1.5" x 2" hole patterns. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 3" Width x 3" Height Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag

RAM Mount Universal X-Grip™ Holder Handlebar Rail Mount Part #: RAM-B-149Z-UN7U The RAM-B-149Z-UN7U consists of a double socket arm, handlebar rail mount with zinc coated u-bolt base and universal spring loaded X-Grip™ holder for cell phones. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the both ends of the socket arm; this with a twist of the arm knob, allows you can move the suction cup X-Grip™ mount to your optimum viewing position. The spring loaded X-Grip™ holder expands and contracts, allowing for a perfect custom fit of your cell phone. Sometimes, its all about the design. If you are looking for a compact mount for your cell phone without that cookie cutter shape, you've found it. The RAM X-Gripȁ has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The perfect compliment to the modern sleek interior of today's vehicles, the RAM X-Grip™ is the cell phone holder evolved. Compatible and interchangeable with a wide range of popular RAM Mounting products, this elegant holder is ready to compliment your phone and become the most useful accessory in your vehicle. Compatible Devices: Apple iPhone 4S WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 4 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3G WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone (1st Generation) Apple iPod touch (All Models) Apple iPod (G1-G5) Samsung Galaxy S7 Samsung Galaxy S7 Edge All devices that maintain the following dimensions below: Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable 3. Versatility of holder allows for attachment to many RAM-to-RAM ball mounts 4. Single socket technology allows for multiple adjustment angles and articulation of device Material: High Strength Composite, Rubber Tips & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Mount Universal Finger Grip Holder Surface Mount Part #: RAM-B-138-UN4 Simply choose the base mounting hardware and the possibilities become endless with a RAM flat surface mount. Four mounting holes in the round ball base easily accommodate up to a #10 screw. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Universal Finger Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-184-UN4U The base consists of a 1" diameter rubber ball, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. Multiple pivot points, rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Included with Purchase: (1 qty) Universal Finger Grip™ holder (1 qty) Base/ball adaptor (attaches directly to cradle) (1 qty) Standard size double socket arm (1 qty) Mounting base (mounts to either brake/clutch reservoir or rail/handlebar) Hardware for mounting to either brake/clutch reservoir or rail/handlebar Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: *The RAM-B-174-UN4U can mount to both the brake/clutch reservoir or any round rail that is 0.5" to 1.25" in diameter.The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN4U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

RAM Univeral Finger Grip Holder ATV/UTV Strap Mount Part #: RAM-B-149Z-2-UN4 Whether your UTV or ATV is bone stock or loaded with accessory racks and guards, the new RAM Strap Base lets you choose the best possible mounting location for almost anything. Designed for a clean installation, this base accommodates most common tubing sizes on UTV?s and ATV's, allowing for the placement of the RAM rubber ball base. Safely concealing a strap clamp in a compact housing, you won't have to worry about exposed sharp edges or unwanted loosening. With the ball base in place, you have the foundation for mounting everything from GPS, Cell Phones, Radios, or maybe the famous RAM self leveling drink cup holder. No matter what you choose to do with it, you'll wonder why your UTV or ATV didn?t come from the factory with this must-have product. Strap Dimensions: 1.57" (40mm) to a maximum of 3.15" (80mm) Universal Finger Grip™ Holder Description: The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. The spine plate contains the universal AMPs and 1.5" x 2" hole patterns. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 3" Width x 3" Height Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Universal Finger Grip Holder Suction Cup Mount Part #: RAM-B-166-UN4U Suction Cup Twist Lock Mount Description: RAM suction cup twist lock ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach. RAM's patented design also dampens shock and vibration helping to extend the life of your mobile device. Universal Finger Grip™ Holder Description:The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite and Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag

RAM Universal Finger-Grip™ Phone/Radio Holder The RAM Composite Universal Finger Grip Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices. Spine Plate Dimensions: 2.5W x 5.0H" Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0" Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5" Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5" Material: High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag.

RAM Universal Finger Grip Glare Shield Clamp Mount Part #: RAM-B-177UN4 The RAM-B-177-UN4 consists of a glare shield clamp base, double socket arm and universal Finger Grip™ holder. Simply locate the clamp on any clamping surface up to 1.12" thick and gently snug the nylon thumb screws. The double ball & socket system will provide perfect viewing angles to get the most from your electronic device. The RAM glare shield clamp with double ball & socket system is far and away the most discrete and clean way to mount most any compact electronic device to the glare shield of your aircraft. The RAM Composite Universal Finger Grip™ Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount. The perfect solution that is the best phone mount, car mount, motorcycle mount and can be used with several other phone accessories including samsung accessories and lg accessories. The spine plate contains the universal AMPs and 1.5" x 2" hole patterns. This mount is designed to hold the following devices: Cell Phones (check measurements below for dimensions) 2-Way Radios GPS Devices Works with OtterBox (Defender, Commuter, Impact) Cases, Phones with Bumper, Twisted Metal Case and More Perfect rugged solution for the Blackberry, HTC Evo, Droid X, iPhone, and More Use on your Motorcycle, ATV, UTV, Car, Boat and More Mount will attach to flat surfaces with the following dimensions: Min: 4.4mm / 0.17" Max: 28.0mm / 1.12" Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Part number reflects product packaged in clear clam shell for store shelf display.

RAM Mount Universal X-Grip Holder Yoke Glare Mount Part #: RAP-B-121-UN7U RAM Composite Clamp Mount with Universal X-Grip™ Holder. Rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality composite materials insure your device is safe, secure, and within easy reach. The clamp base fits a rail or edge lip from 0.625" to a maximum of 1.25". The mounting base can also accept a second ball giving you the ultimate double ball base. Extra ball not included with purchase of this mount. Compatible Devices: Apple iPhone 4S WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 4 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3G WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone (1st Generation) Apple iPod touch (All Models) Apple iPod (G1-G5) All devices that maintain the following dimensions below: Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable 3. Versatility of holder allows for attachment to many RAM-to-RAM ball mounts 4. Single socket technology allows for multiple adjustment angles and articulation of device Material: High Strength Composite, Rubber Tips & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size

RAM Mount Universal X-Grip Holder Diamond Base Surface Mount Part #: RAM-B-102-UN7U The RAM-B-102-UN7U consists of a double socket arm, diamond base and universal spring loaded X-Grip™ holder for cell phones. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the both ends of the socket arm; this with a twist of the arm knob, allows you can move the suction cup X-Grip™ mount to your optimum viewing position. The spring loaded X-Grip™ holder expands and contracts, allowing for a perfect custom fit of your cell phone. Sometimes, its all about the design. If you are looking for a compact mount for your cell phone without that cookie cutter shape, you've found it. The RAM X-Gripȁ has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. The perfect compliment to the modern sleek interior of today's vehicles, the RAM X-Grip™ is the cell phone holder evolved. Compatible and interchangeable with a wide range of popular RAM Mounting products, this elegant holder is ready to compliment your phone and become the most useful accessory in your vehicle. Compatible Devices: Apple iPhone 4S WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 4 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3G WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone (1st Generation) Apple iPod touch (All Models) Apple iPod (G1-G5) All devices that maintain the following dimensions below: Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable 3. Versatility of holder allows for attachment to many RAM-to-RAM ball mounts 4. Single socket technology allows for multiple adjustment angles and articulation of device Material: High Strength Composite, Rubber Tips & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.

RAM Mount Universal X-Grip Holder Composite Surface Mount Part #: RAP-B-138-UN7 The RAP-B-138-UN7 consists of a double socket arm, 2.5" round base base and universal spring loaded X-Grip™ holder for cell phones. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at the both ends of the socket arm; this with a twist of the arm knob, allows you can move the suction cup X-Grip™ mount to your optimum viewing position. The spring loaded X-Grip™ holder expands and contracts, allowing for a perfect custom fit of your cell phone. Compatible Devices: Apple iPhone 4S WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 4 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3G WITH OR WITHOUT Bumper, Skin or Case Apple iPhone 3 WITH OR WITHOUT Bumper, Skin or Case Apple iPhone (1st Generation) Apple iPod touch (All Models) Apple iPod (G1-G5) All devices that maintain the following dimensions below: Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable 3. Versatility of holder allows for attachment to many RAM-to-RAM ball mounts 4. Single socket technology allows for multiple adjustment angles and articulation of device Material: High Strength Composite, Rubber Tips & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size

Universal X-Grip Holder f/12" Tablets The new RAM X-Grip line of products just got bigger and better. This new model is just what you've been looking for to hold your favorite tablet. Just like the devices it was made for, it is everything you need and nothing you don't. Simple to open and close, the spring loaded RAM X-Grip leaves the outside edge of your tablet almost completely free of annoying obstructions. Soft rubber fingers apply just enough force to keep your tablet in safe and secure. Compatible with a wide range of mounting solutions, your tablet is sure to find a home no matter where your travels take you. The RAM-HOL-UN11U holder expands and contracts for perfect fit of most 10" and 12" tablets with or without sleeves, as well as some smaller tablets. This holder by RAM consists of a composite spring loaded holder, expandable grip arms and additional bottom support keeper. ** The RAM-HOL-UN11U is compatible with the iPad Pro WITHOUT CASE ONLY. ** Compatible Devices (WITH OR WITHOUT CASE):  Microsoft Surface Pro 3 Samsung Galaxy Note® Pro 12.2 Most 12" Screen Tablets X-Grip Holder Dimensions: Minimum Width = 7.25" Maximum Width = 8.75" Maximum Length (WITHOUT additional supports) = Unlimited Maximum Length (WITH additional supports) = 10.25" Depth = 0.875" X-Grip Holder Features: Spring loaded cradle expands and contracts for perfect fit of your tablet Rubber coated tips will hold your tablet firm and stable Versatility of cradle allows for attachment to many 1" socket mounts Socket technology allows for multiple adjustment angles and articulation of your tablet Easy access grip knobs, located on the back of the cradle for quick release of your tablet Multiple mounting access points on the back of the cradle Additional support keeper at the bottom of the cradle Full access to all ports Lifetime warranty Made in the U.S.A. Material: Powder Coated Marine Grade Aluminum, Marine Grade Stainless Steel Components & High Strength Composite Note: The "U" in the part number reflects product packaged in poly bag.

RAM Universal X-Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-174-UN7 The RAM-B-174-UN7 consists of a double socket arm, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter and universal X-Grip™ cell phone holder. Designed into the mount is a 1" diameter patented rubber ball and socket system with adjustment points at both ends of the double socket arm. With a twist of the arm knob, you can move the cell phone holder to your optimum viewing position. The spring loaded X-Grip™ has a clean and clever four leg design that sports great holding power without hiding your phone behind foam pads and plastic. X-Grip™ Holder Features: 1. Spring loaded holder expands and contracts for perfect fit of your device 2. Rubber coated tips will hold device firm and stable X-Grip™ Holder Dimensions: Minimum Width = 0.875" (Devices at 0.875" must be a minimum of 4" in height to fit into holder) Maximum Width = 3.25" Depth = 0.875" Material: High Strength Composite & Powder Coated Marine Grade Aluminum Ball Size: 1" Rubber Ball "B" Size Note: Note: Part number reflects product packaged in clear clam shell for store shelf display. To see if the RAM-B-174-UN7 will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".

Universal X-Grip® Holder w/1" Ball Base The RAM-B-202-UN9U consists of a composite spring loaded cradle, expandable grip arms, additional bottom support keepers and 1" ball base adapter. Included are extra easy access grip knobs, located on the back of the cradle for quick release of your tablet. The RAM-B-202-UN9U expands and contracts for perfect fit of most 10" tablets with or without sleeves, as well as some smaller tablets. The included 1" ball base includes hardware to attach directly to the back of the cradle and is compatible with all "B" size double socket arms. Please verify dimensions of your tablet below for compatibility with the X-Grip®. The X-Grip® holder is compatible with tablets devices that will fit the dimensions listed below. It is important to verify the dimensions of your tablet with a case/sleeve/skin when determining the overall size. Cradle Dimensions: Minimum Width = 6.25" Maximum Width = 8.1" Depth = 0.875" Maximum Length (using additional supports) = 10.25" Features: Spring loaded cradle expands and contracts for perfect fit of your tablet Rubber coated tips will hold your tablet firm and stable Versatility of cradle allows for attachment to many 1" socket arms Socket technology allows for multiple adjustment angles and articulation of your tablet Easy access grip knobs, located on the back of the cradle for quick release of your tablet Multiple mounting access points on the back of the cradle Additional support keeper at the bottom of the cradle Full access to all ports Lifetime warranty Made in the U.S.A. Material: Marine Grade Stainless Steel Components & High Strength Composite

RAM Universal X-Grip IV Large Phone/Phablet Holder with 1" Ball The X-Grip IV has a clean and clever four leg design that sports great holding power without hiding your phone or phablet behind foam pads and plastic. The perfect compliment to the modern sleek interior of today's vehicles, the X-Grip IV is the phablet holder evolved. Compatible and interchangeable with a wide range of popular RAM Mounting products, this elegant holder is ready to compliment your phablet and become the most useful accessory in your vehicle. Compatible Devices: HTC Droid DNA Huawei Ascend P1 LG Intuition Nokia Lumia 920 Pantech Vega No. 6 Samsung GALAXY Note II Samsung GALAXY S III The X-Grip IV holder is compatible with handheld devices that will fit the dimensions listed below. It is important to verify the dimensions of your handheld device with a case/sleeve/skin when determining the overall size. Holder Dimensions: Minimum Width = 1.75" Maximum Width = 4.5" Features: 1. Rustproof 2. High strength composite and stainless steel construction 3. Spring loaded holder expands and contracts for perfect fit of your device 4. Rubber coated tips will hold device firm and stable 5. Versatility of holder allows for attachment to many RAM ball mounts 6. Lifetime warranty Material: High Strength Composite & Stainless Steel Ball Size: 1" Rubber Ball "B" Size Note: The "U" in the part number reflects product packaged in poly bag.