Fits flush to boats transom or exterior. Plug has molded screwdriver slot. Made of nylon. Fits 1-1/8" opening, flange dia. is 2-3/16, tube i.d. is 7/8", 1/2" plug with o-ring. Display packed.

Fits flush to boats transom or exterior. Plug has molded screwdriver slot. Made of nylon. Fits 1-1/8" opening, flange dia. is 2-3/16, tube i.d. is 7/8", 1/2" plug with o-ring. Display packed.

Wally Plug with O-Rings FatSac Replacement Ballast Bag Plug is used to plug unused holes on FatSac ballast bags. Fits the proprietary thread pattern used on FatSac bags making a perfect water-tight seal that won't leak or back out over time. Off-the-shelf FatSac ballast bags include the required number of bag plug fittings, but if you're misplaced one or want to have extras, this is the fitting you need to close any unused holes on the bag. FatSac ballast fittings have been designed with you in mind.  All of the fittings make connecting pumps and hoses to your FatSac a quick and simple task.  Features: Wally plug O-ring *Sold as an Individual WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Brass Plug w/O-Ring for Pumps Typical Application: Compensating line brass plug of the UP series helms Specifications: 1/4 NPT PLUG Helm Side = 1/4 NPT

Air Release Plug with O-Rings The FatSac Air Release plug makes it easy to purge air from your wakeboard ballast bags without spilling any water. The Air Release plug is a direct replacement for the standard ballast plug used with FatSac wakeboard ballast bags, but allows you to easily "burp" excess air out of the bag by simply loosening the fitting slightly. You don't have to completely remove the fitting from the bag, and you don't have to worry about spilling a lot of water, just loosen to vent, and then tighten back down. FatSac ballast fittings have been designed with you in mind. All of the fittings make connecting pumps and hoses to your FatSac Ballast Bags a quick and simple task. No more struggling with old waterbed valves and water spilling inside the boat. Simply twist, pull, replace and you're ready to go!  Features: Air release plug Turn to release air For manual filling, not for venting automatic systems *Sold as an Individual WARNING: This product can expose you to chemicals including Diisononyl Phthalate (DINP) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Drain Plug with O-Ring for ARG Strainer 2009 & Newer Drain plug with O-ring for ARG Strainer. For Strainers older than 2008 use ARG-506.

Drain Plug with O-Ring for ARG Strainers 2008 & Older Drain Plug before 080101 for ARG Strainers 2008 & Older

Designed for aluminum boats as drain for transom, livewell or baitwell. Easily flanged fitting eliminates need for welding. O-ring forms watertight seal on .04-.09" wall thickness. 1" dia.

      Sprayway manufactures a complete line of industrial MRO, automotive, screen print and housekeeping products since 1947. Sprayway has been an innovative industry leader, and its Sprayway Glass Cleaner is recognized as "The World's Best." From marine detailing to industrial maintenance, whether it is a detailing wax or an industrial lubricant, Sprayway provides wide-ranging industries with the products they need.     The World's Best Glass Cleaner - Excellent for windows, mirrors, windshields and other glass surfaces! For cleaning and polishing glass, mirrors, windshields and windows. This easy-to use, fast acting product uses a clinging foam to break up soils and hold them - even on vertical surfaces. There is no dripping, no running and no streaking. With an exclusive formulation using denatured alcohol and no ammonia, this product cleans thoroughly, dries quickly, requires no rinsing and leaves a pleasant, fresh aroma.   SHOP: https://www.clrmarine.com/462m4/manufacturers/s/sprayway.html     Specials    Closeouts    Remanufactured    Rebates  

March LC-3CP-MD Magnetic Drive Pump 230V The most common application for the LC-3CP-MD Magnetic Drive Pump is for marine air conditioning and fountains. This unit will handle up to a 24,000 BTU Air Conditioner March Pump's industrial LC-3CP-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 8.5 gallons per minute at 4 feet, and its maximum head is 19 Feet (or around 8PSI).  The LC-3CP-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Buna N, Cupric Nickel, Ceramic, and Ceramic Magnet.  When submerged, Epoxy, Stainless Steel, Polysulfone, and the Cord are also in contact with the solution. The inlet connection is .075 inch female pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.05 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 25PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius. The March LC-3CP-MD centrifugal magnetic drive pump is capable of handling fresh water, salt water, and mild chemicals.   Unit System 60Hz 50Hz Max Flow 8.5 GPM 31 LPM Max Head 19 FT 4.3 M Power .05 HP .037 KW Electrical 115V 50/60HZ or 230V 50/60HZ Submersible Yes   Type Centrifugal Mag Drive Inlet 3/4"FPT Outlet 1/2"MPT Wet End Polypropylene (Front and Rear Housing, Impeller), Cupric Nickel (Cooling Tube), Buna N (O-Ring, Cooling Tube Seal), Ceramic (Shaft, Thrust Washer), Ceramic Magnet Uses Submersible or Open Air When submerged, the following is also in contact with the solution Epoxy, Stainless Steel, Polysulfone, Cord

ConnectPro® Charging/Trolling Receptable, Plug & 6-Guage Adapter The ConnectPro® system features locking plug and receptacle and spring clamping connection, which provide a secure electrical contact. Receptacle is universal design for 2-or-3 wire configuration, 12, 24, 12//24, 24//36 or 36 volt systems. Features: Watertight sealing cap Corrosion resistant, plated brass electrical components with drain holes in receptacle to keep water away from electrical components Standard 1-1/8 diameter mounting hole and accepts up to 8 gauge wire Includes mounting plate Plug has O-ring seal for waterproof connections Weather resitant plug cover Accepts 16 to 8 gauge wire WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

AQUA KING™ II Supreme 5.0 (24VDC) Fresh Water Pump w/Strainer & Fittings SHURFLO®’s AQUA KING™ II Fresh Water Pumps are designed for boats with multi-fixtures providing “Just like home” shower pressure, and can operate at lower flow conditions without cycling. A built in mechanical bypass function enables these pumps to vary the flow rate for any on demand condition, without the need for an accumulator. With heavy duty motors built to withstand the tough marine environment these motors feature an electro-coated seamless shell motor, O-ring sealed end bells, and complete sealed wire entries on the motor shell and pressure switch. The AQUA KING™ II Fresh Water Pumps can run dry without damage. Inlet strainer and ½" hose barb fittings are included. (aftermarket models only). Ignition protected. Thermally protected. 3 Year Warranty Features: Sealed Switch Sealed Motor Corrosion Resistant Electro Coated Motor Independent Chambers Built-in Check Valve Co-Molded Diaphragm Adjustable Switch & By-Pass Self-Priming up to 6 Feet Dry Run Capability Thermally Protected Ignition Protected, CE Specifications: 24 VDC 5.0 GPM [18.9 LPM] 7 Amps (Max.) 55 PSI [3.8 BAR] Intermittent Duty Multi-fixture Applications 1/2" NPS-M Inlet/Outlet

Service and fitting kits for SeaStar cylinders and helms with ORB fittings. Made of corrosion resistant stainless steel. Fittings thread into cylinders or helms via Positionable O-ring hose ports. Fittings can be easily orientated in any direction to accommodate tube routing. Not for use in an NPT helm or cylinder hose fitting port.

Service and fitting kits for SeaStar cylinders and helms with ORB fittings. Made of corrosion resistant stainless steel. Fittings thread into cylinders or helms via Positionable O-ring hose ports. Fittings can be easily orientated in any direction to accommodate tube routing. Not for use in an NPT helm or cylinder hose fitting port.

Service and fitting kits for SeaStar cylinders and helms with ORB fittings. Made of corrosion resistant stainless steel. Fittings thread into cylinders or helms via Positionable O-ring hose ports. Fittings can be easily orientated in any direction to accommodate tube routing. Not for use in an NPT helm or cylinder hose fitting port.