15A Battery Charger - 24V - 3-Bank - 3-Stage w/Dip Switch & Lugs This advanced fully automatic three-stage 15 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 3 separate battery banks. Features: High efficiency Commercial Grade Lightweight Quiet operation Industry Proven Design – 1000s of units in operation 2 or 3 stage charging (user selectable) 120 or 230 VAC, 50/60 Hz (user selectable) Voltage meter display – Ammeter and LED power status For all types of Lead Acid batteries Charge with a battery load or stand alone Use as a power supply or DC UPS UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity Charge 3 banks of batteries at once – no isolator necessary Specifications: Input: 120 VAC or 230 VAC Output: 24 VDC Amps: 15 Amps Remote Control: 900-RC Weight: 6 (lbs) Weight: 2.72 (kg) Dimensions: 10.5 x 8.5 x 3 (in) Dimensions: 26.7 x 21.6 x 7.6 (cm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

15A Battery Charger - 12V - 3-Bank - 3-Stage w/Dip Switch & Lugs This advanced fully automatic three-stage 15 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload and short-circuit protection. The unit allows charging of up-to 3 separate battery banks. Features: High efficiency Commercial Grade Lightweight Quiet operation Industry Proven Design – 1000s of units in operation 2 or 3 stage charging (user selectable) 120 or 230 VAC, 50/60 Hz (user selectable) Voltage meter display – Ammeter and LED power status For all types of Lead Acid batteries Charge with a battery load or stand alone Use as a power supply or DC UPS UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity Charge 3 banks of batteries at once – no isolator necessary Specifications: Input: 120 VAC 60 Hz or 230 VAC 50 Hz Output: 12 VDC Amps: 15 Amps Weight: 4.4 (lbs) Weight: 1.96 (kg) Dimensions: 8.5 x 8.5 x 3 (in) Dimensions: 21.6 x 21.6 x 7.6 (cm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

25A Battery Charger - 24V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor This advanced fully automatic three-stage 25 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit, reverse polarity and thermal overload protection. The unit allows charging of up-to 2 separate battery banks. Features: Switch mode technology for high efficiency, lightweight and quiet operation Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell Can charge 2 banks of batteries simultaneously, no isolator necessary Can be used as a power supply or DC UPS when used in conjunction with a battery User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries “Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries Voltmeter and Ammeter for monitoring Fan cooled based on output current Protections: Short circuit, overload, reverse battery connection and over temperature Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively Specifications: Input: 120 VAC or 230 VAC Output: 24 VDC Amps: 25 Remote Control: 900-RC Weight: 9 (lbs) Weight: 4.1 (kg) Dimensions: 13.03 x 9.6 x 3.82 (in) Dimensions: 331 x 244 x 97 (mm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Test bench Automotive Marine Communications sites Battery back-up systems Hobby WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

40A Battery Charger - 24V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor This advanced fully automatic three-stage 40 Amp battery charger is ideal for charging all types of 24 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks. Features: Switch mode technology for high efficiency, lightweight and quiet operation Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell Can charge 2 banks of batteries simultaneously, no isolator necessary Can be used as a power supply or DC UPS when used in conjunction with a battery User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries “Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries Voltmeter and Ammeter for monitoring Fan cooled based on output current Protections: Short circuit, overload, reverse battery connection and over temperature Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively Specifications: Input: 120 VAC or 230 VAC Output: 24 VDC Amps: 40 Remote Control: 900-RC Weight: 9 (lbs) Weight: 4.1 (kg) Dimensions: 15 x 9.61 x 3.82 (in) Dimensions: 381 x 244 x 97 (mm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

50A Battery Charger - 12V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor This advanced fully automatic three-stage 50 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks. Features: Switch mode technology for high efficiency, lightweight and quiet operation Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell Can charge 2 banks of batteries simultaneously, no isolator necessary Can be used as a power supply or DC UPS when used in conjunction with a battery User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of stand-alone and loaded Lead Acid Batteries “Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries Voltmeter and Ammeter for monitoring Fan cooled based on output current Protections: Short circuit, overload, reverse battery connection and over temperature Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively Specifications: Input: 120 VAC 60 Hz or 230 VAC 50 Hz Output: 12 VDC Amps: 50 Remote Control: 900-RC Weight: 9.0 (lbs) Weight: 4.1 (kg) Dimensions: 13.03 x 9.60 x 3.82 (in) Dimensions: 331 x 244 x 97 (mm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

80A Battery Charger - 12V - 2-Bank - 3-Stage w/Dip Switch & Lugs - Includes Temp Sensor This advanced fully automatic three-stage 80 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 2 separate battery banks. Features: Switch mode technology for high efficiency, lightweight and quiet operation Automatic operation for ALL Lead Acid Batteries Flooded, AGM or Gel Cell Can charge 2 banks of batteries simultaneously, no isolator necessary Can be used as a power supply or DC UPS when used in conjunction with a battery User Configurable AC Input voltage 120 or 230 VAC, 50 / 60 Hz User Selectable ( by DIP Switch) for 2 or 3 stage, rapid and safe charging of standalone and loaded Lead Acid Batteries “Half Power Mode” reduces maximum charging current to half the rated capacity, allows for safe charging of lower capacity batteries Voltmeter and Ammeter for monitoring Fan cooled based on output current Protections: Short circuit, overload, reverse battery connection and over temperature Includes temperature sensor to prevent under/overcharging of battery if temperature varies extensively Specifications: Input: 120 VAC 60 Hz or 230 VAC 50 Hz Output: 12 VDC Amps: 80 Remote Control: 900-RC Weight: 9 (lbs) Weight: 4.1 (kg) Dimensions: 15 x 9.61 x 3.82 (in) Dimensions: 381 x 244 x 97 (mm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

30A Battery Charger - 12V - 3-Bank - 3-Stage w/Dip Switch & Lugs This advanced fully automatic three-stage 30 Amp battery charger is ideal for charging all types of 12 Volt lead-acid batteries ( Flooded / Absorbed Glass Mat (AGM) / Gel Cell) from a 120 V, 60 Hz or 230 V, 50 Hz AC source. By means of a DIP switch setting, conversion to a two-stage algorithm is possible to charge batteries connected to a DC load (DC UPS). The unit can also be used as a DC Power Supply. Features include overload, short-circuit and over-temperature protection. The unit allows charging of up-to 3 separate battery banks. Features: High efficiency Commercial Grade Lightweight Quiet operation Industry Proven Design – 1000s of units in operation 2 or 3 stage charging (user selectable) 120 or 230 VAC, 50/60 Hz (user selectable) Voltage meter display – Ammeter and LED power status For all types of Lead Acid batteries Charge with a battery load or stand alone Use as a power supply or DC UPS UPC: Universal Protection Circuit – short circuit, overload, reverse battery polarity Charge 3 banks of batteries at once – no isolator necessary Specifications: Input: 120 VAC 60 Hz or 230 VAC 50 Hz Output: 12 VDC Amps: 30 Amps Weight: 7 (lbs) Weight: 3.17 (kg) Dimensions: 10.5 x 8.5 x 3 (in) Dimensions: 26.7 x 21.6 x 7.6 (cm) Safety: Listed to UL Standard UL-1564, EMI Compliant to FCC Part 15(B), Class B Warranty: 2 Year Limited Applications: Automotive Recreational vehicles Marine Communications sites Battery back-up systems WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

P12 Gen2 Battery Charger - 40A - 3-Bank Features: Four stage, three output, dry mount design, for use in harsh environments. Rugged, finned aluminum case PreFloat™ stage prevents over charging Power factor corrected for efficient use of AC Intuitive diagnostic screens User defined charge profiles and customizable settings Provides charging for up to three battery banks Large, bright display Multi-language: English, French, German, Italian, Spanish Charge Coordination with Blue Sea Systems Automatic Charging Relays (ACR) controls ACR state ensuring proper float stage for each battery Battery Temperature Compensation - adjusts charge voltage based on battery temperature AC over and under voltage shut down and automatic restart Over and under battery temperature protection - charger will not operate if battery temperature rises above or falls below a set value DC over voltage and reverse polarity protection Surge and short circuit protection Specifications: Total Output Current: 40A Input AC Current: 7.5A @ 100V AC / 3.75A @ 200V AC Maximum Output Voltage: 16V DC Nominal Voltage: 12V DC Ignition Protected: Yes Number of Outputs: 1 negative / 3 positive Universal AC Input Voltage: 90-265V AC AC Input Frequency: 45-65Hz Output Voltage Accuracy: 0.05V Typical Float Voltage:13.5V DC Minimum Operating Temperature: -20° C Maximum Operating Temperature: 70° C Minimum Storage Temperature: -30° C Maximum Storage Temperature: 80° C Battery Types: AGM / Flooded Lead Acid / Gel / TPPL (Thin Plate Pure Lead) Recommended for Battery Bank Sizes: 440Ah Maximum Example: 4 x Group 31 / 60Ah Minimum Example: 2 x Group 31 Warranty: 5 Year Height: 13.03" (330.96 mm) Width: 8.46" (214.88 mm) Depth: 3.66" (92.96 mm) Weight: 13.00lb (5.9 kg) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Pro Series Dolphin Battery Charger - 24V, 80A, 230VAC - 50/60Hz The Dolphin Series of battery chargers has always been recognized for its outstanding quality, which the manufacturer is proud to support with a 2-year warranty. Due to production on a wide scale, Dolphin is able to offer high-quality, truly international battery chargers at a reasonable price. The Pro Range, which allows battery banks of up to 1000 amps to be charged, can be equipped with an optional touch view touchscreen. It provides an intuitive display of measurements as well as charging phases (boost, absorption, and float), the allocated available power, and possible operating faults. The Pro range is equipped with communication via CAN bus, which means it can be used professionally in all land and industrial energy management sectors. Features: 24V-80A Dolphin Pro (230 VAC 50/60 Hz input voltage only) All Dolphin Battery Chargers and accessories are CE-marked and manufactured to UL and ABYC specifications The Pro Touch Range features a built-in TouchView remote in place of the standard display panel on the Pro chargers The Touchview control panel gives the user more information and control of the charger functions LED Display for programming and monitoring functions Temperature sensor for battery compensation Switch mode technology and a three-stage charging design with a power supply Modern, lightweight, and compact design with white aluminum powder-coated casing Universal AC input with automatic voltage switching 115/230 VAC 50/60 Hz (24V-80A, 24V-100A, and 24V-150A are 230VAC 50/60 Hz ONLY) 4 screw simple install with easy access removable panel ISO 9002-certified manufacturing plant Three-Stage Charging Curve Bulk Stage: A high current is sent to the battery until it reaches approximately 80% of its full charge. Absorption Stage: The voltage level is maintained and the current is reduced until the battery is 100% charged.  Float Stage: Voltage and current are reduced to maintain the battery. Float gives what the battery requires.

Pro Series Dolphin Battery Charger - 24V, 100A, 230VAC - 50/60Hz The Dolphin Series of battery chargers has always been recognized for its outstanding quality, which the manufacturer is proud to support with a 2-year warranty. Due to production on a wide scale, Dolphin is able to offer high-quality, truly international battery chargers at a reasonable price. The Pro Range, which allows battery banks of up to 1000 amps to be charged, can be equipped with an optional touchview touchscreen. It provides an intuitive display of measurements as well as charging phases (boost, absorption, and float), the allocated available power, and possible operating faults. The Pro range is equipped with communication via CAN bus, which means it can be used professionally in all land and industrial energy management sectors. Features: 24V-100A Dolphin Pro (230 VAC 50/60 Hz input voltage only) All Dolphin Battery Chargers and accessories are CE-marked and manufactured to UL and ABYC specifications The Pro Touch Range features a built-in TouchView remote in place of the standard display panel on the Pro chargers  The Touchview control panel gives the user more information and control of the charger functions LED Display for programming and monitoring functions Temperature sensor for battery compensation Switch mode technology and a three-stage charging design with a power supply Modern, lightweight, and compact design with white aluminum powder-coated casing Universal AC input with automatic voltage switching 115/230 VAC 50/60 Hz (24V-80A, 24V-100A, and 24V-150A are 230VAC 50/60 Hz ONLY) 4 screw simple install with easy access removable panel ISO 9002-certified manufacturing plant Three-Stage Charging Curve Bulk Stage: A high current is sent to the battery until it reaches approximately 80% of its full charge. Absorption Stage: The voltage level is maintained and the current is reduced until the battery is 100% charged.  Float Stage: Voltage and current are reduced to maintain the battery. Float gives what the battery requires.

Pro Series Dolphin Battery Charger - 24V, 60A, 110/220VAC - 50/60Hz The Dolphin Series of battery chargers has always been recognized for its outstanding quality, which the manufacturer is proud to support with a 2-year warranty. Due to production on a wide scale, Dolphin is able to offer high-quality, truly international battery chargers at a reasonable price. The Pro Range, which allows battery banks of up to 1000 amps to be charged, can be equipped with an optional touch view touchscreen. It provides an intuitive display of measurements as well as charging phases (boost, absorption, and float), the allocated available power, and possible operating faults. The Pro range is equipped with communication via CAN bus, which means it can be used professionally in all land and industrial energy management sectors. Features: 24V-60A Dolphin Pro All Dolphin Battery Chargers and accessories are CE-marked and manufactured to UL and ABYC specifications The Pro Touch Range features a built-in TouchView remote in place of the standard display panel on the Pro chargers The Touchview control panel gives the user more information and control of the charger functions LED Display for programming and monitoring functions Temperature sensor for battery compensation Switch mode technology and a three-stage charging design with a power supply Modern, lightweight, and compact design with white aluminum powder-coated casing 4 screw simple install with easy access removable panel ISO 9002-certified manufacturing plant Three-Stage Charging Curve Bulk Stage: A high current is sent to the battery until it reaches approximately 80% of its full charge. Absorption Stage: The voltage level is maintained and the current is reduced until the battery is 100% charged.  Float Stage: Voltage and current are reduced to maintain the battery. Float gives what the battery requires.

RealPRO Series Battery Charger - 24A - 4-Bank RealPro Series battery chargers (formerly Recreation Series) are an affordable, reliable, and safe battery charging system designed for everyday use. The system is engineered for users who need a charging system on an occasional basis and may not want or need the capabilities of a heavier-duty and higher-amperage product. It is designed for use in many types of applications, including bass boats, runabouts, pontoon boats, other watercraft, automobiles, ATVs, golf carts, and other similar uses. The system delivers sophisticated capabilities and superior value to customers. Battery Charging Systems Designed for Everyday Applications: Affordable, reliable, and safe Unmatched performance, reliability, safety, and quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 satisfied customers! Wide variety of applications Universal input (100-240 VAC 50/60HZ) Features: 4 bank battery charger  Approved for wet cell and absorbed glass mat (AGM) batteries Designed for use in fresh and saltwater Dependable, rugged construction, and waterproof Independent outputs and fully automatic Battery maintenance mode Two-year warranty DC charge cables = 5ft and AC power cord = 3ft Approved and meets ISO 8846 marine standards LED lights indicate "Each Battery’s" state of charge Reverse polarity protection and no installation restrictions Ignition protected (US Coast Guard 33 CFR 183.410) FCC 15 Parts A and B Interference Compliant May Be Used in Many Types of Sporting applications, Including: Bass Boats Runabouts Pontoons Automobiles ATVs Golf Carts

Sportsman Series Battery Charger - 10A - 1-Bank - 12V Our customers asked for a series of chargers that were smaller, lighter and economically affordable. The Sportsman Series of chargers answers these needs. This line of chargers is designed for all types of battery applications. Sportsman chargers have all the safety and reliability features that have made PRO Charging Systems chargers the #1 choice of most boat manufacturers, dealers and over 750,000 customers across the country. Advanced microprocessors and LED readings make the units even easier to use. Battery Charging System Designed for Use On Land and in Fresh and Salt Water The “Green” Charger: Totally “Repairable” Not a Throw-Away Unmatched Performance, Reliability, Safety and Quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 of Our Satisfied Customers! Fully Automatic and Totally Waterproof Features: Approved for Wet Cell and AGM batteries Models also available for Gelled Electrolyte batteries Designed for use in fresh and saltwater DeltaVolt® Intuitive Charging Technology Waterproof, dependable, rugged construction Independent outputs Fully automatic / multi stage charging Zero spark technology Battery maintenance mode On-board diagnostic codes Temperature compensated Advanced microprocessor controlled Battery systems available: 12V – 48V LED lights indicate the state of charge Reverse polarity protected No installation restrictions FCC Parts A & B interference compliant DC charge cables = 5' AC power cord = 3' Approved and meets ISO 8846 Marine standards Ignition protected (US Coast Guard 33 CFR 183.410 May be used in many types of sporting applications including: Inland Watercraft Salt Water Watercraft Motorcycles Golf Carts Utility Vehicles… This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RealPRO Series Battery Charger - 6A - 1-Bank - 12V RealPro Series battery chargers (formerly Recreation Series) are an affordable, reliable and safe battery charging system designed for everyday use. The system is engineered for users who need a charging system on an occasional basis and may not want or need the capabilities of a heavier duty and higher amperage product. It is designed for use in many types of applications including bass boats, runabouts, pontoon boats, other watercraft, automobiles, ATVs, golf carts and other similar uses. The system delivers sophisticated capabilities and superior value to customers. Battery Charging Systems Designed for Everyday Applications Affordable, Reliable and Safe Unmatched Performance, Reliability, Safety and Quality TROUBLE FREE – Just Plug It In and Forget It! Join Over 750,000 of Our Satisfied Customers! Wide Variety of Applications Universal Input (100-240 VAC 50/60HZ) Features: Approved for Wet Cell and Absorbed Glass Mat (AGM) batteries Designed for use in fresh and salt water Dependable, rugged construction and waterproof Independent outputs and fully automatic Battery maintenance mode Two year warranty DC charge cables = 5ft and AC power cord = 3ft Approved and meets ISO 8846 Marine standards Models available to charge 12-24V systems LED lights indicate “Each Battery’s” state of charge Reverse polarity protected and no installation restrictions Ignition protected (US Coast Guard 33 CFR 183.410) FCC 15 Parts A and B Interference Compliant May be used in many types of sporting applications including: Bass Boats Runabouts Pontoons Automobiles ATVs Golf Carts… This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

BatteryLink® Charger - 10Amp - 2-Bank Charge two batteries at or away from the dock with a 10A multistage battery charger and integrated 65A Automatic Charging Relay (ACR) AC charging at the dock: Use AC shore power to charge two isolated battery banks with the 3 Stage 10 Amp battery charger DC charging away from the dock: Share the DC power from the alternator with both the Start and the Auxiliary battery through the integrated 65A ACR Battery Temperature Compensation prolongs battery life Start isolation protects sensitive electronics from voltage sags and spikes Includes LED remote indicator for charge status at the helm Snap-on insulating cover One-piece stainless flange nuts ensure safe and secure connections Specifications Total Output Current: 10A Nominal Voltage: 12V DC Number of Outputs: 1 negative / 2 positive Terminal Stud Torque: 60 in-lb (6.78 Nm) Continuous Rating:65A Intermittent Rating:115A Universal AC Input Voltage: 90-265V AC AC Input Frequency: 50/60Hz Typical Float Voltage:13.5V DC Battery Types: AGM / Flooded / TPPL - Do not mix battery types Cable Size to Meet Ratings:10 AWG Negative Cable / 6 AWG Positive Cable Maximum Battery CCA: 850CCA Maximum Cable Size: 1/0 AWG (50mm) Operating Current: 10mA (No AC Power, ACR Open) / 60mA (No AC Power, ACR Closed) Recommended Battery Bank Sizes: 60Ah Minimum Terminal Stud Size:1/4"-20 (accepts M6 ring terminal) Warranty: 5 Year Combine 30 sec: 13.5V Combine 2 Min: 13.0V Open 10 sec: 12.35V Open 30 sec: 12.75V WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.