March 0125-0029-0100 Impeller Mag Assembly  

March 0125-0055-0100 Impeller Mag Assembly Impeller (Molded) 1.812 Dia for 2C-MD, AC-2CP-MD, LC-2CP-MD made of Polypro/Teflon/Glass

March 0175-0029-0300 Impeller Magnet Assembly  

March 0125-0057-0100 Rear Housing Rear Housing & Plug Assembly LC for LC-2CP-MD made of Polypro/Glass

March 0125-0083-0100 Drive Magnet .250" Bore Fits March Pumps: 809, 815, AC-2CP-MD, BC-2CP-MD, LC-2CP-MD Cruisair PML250, PML250C   Note: This will not fit 809 BR 24vdc With Non-replaceable brushes  

March 0125-0113-0100 Large Base Fits LC-2CP-MD, LC-3CP-MD March Pump models Kit includes base plate and four Rubber isolation grommets made from Polypro/Glass (Black) Does not include mounting screws Use existing base screws to attach to the pump

March 0125-0028-0100 Pump Housing  

March 0135-0130-0200 Impeller Mag Assembly  

March 0809-0107-0200 Impeller Mag Assembly  

March 0151-0029-0500 Impeller Mag Assy  

March Wet End Part # 0125-0108-0100 March Pump- Wet End Assembly Includes All Parts except Motor, Bracket and Drive Magnet   0125-0108-0100 WET END KIT 6PK AC-2CP-MD

March 0155-0112-0400 Impeller Magnetic Assembly Impeller 3.750 Dia (Carbon Bushing) for TE-7S-MD made from 316 SS

March 0155-0112-0800 Impeller Magnetic Assembly Impeller 3.750 Dia (Mica Teflon Bushing) for TE-7S-MD made from 316 SS

March 0150-0030-0100 Polypro Impeller  

March 0125-0142-0100 Marine Pump LC-2M-MD March Pump’s industrial LC-2M-MD is an American submersible seal-less centrifugal magnetic drive pump. It is capable of generating a maximum flow of 5 gallons per minute at 1 foot, and its maximum head is 13 Feet (5.5PSI). The LC-2M-MD pump may be used submerged or not submerged. The pump is Ignition Protected per SAE J1171 and ISO 8846.  It is capable of 12,000 BTU a hour. Max Flow: 18.5 LPM Max Head: 2.7 M Power: 0.014 KW   Electrical/Air: 230V 50/60Hz   230V Motor 6 Foot Cord, Submersible 60Hz: 1Ph 0.025HP/0.019kW, 0.53 AMPS, 3450RPM 50Hz: 1Ph 0.18HP/0.014kW, 0.72 AMPS, 2850RPM   Inlet: 3/8"FPT & 3/4"MPT Outlet: 1/4"MPT   Submersible: Yes   Wet End: Polypropylene (Front Housing, Impeller), Nylon (Rear Housing) Viton (O-Ring), Buna N (O-Ring, Cooling Tube Seal), 316 Stainless Steel (Shaft, Cooling Tube), Ceramic (Thrust Washer), Ceramic Magnet Uses: Submersible or Open Air When submerged, the following is also in contact with the solution: Epoxy, Buna N, Cord Max Internal Pressure: 25 PSI / 1.7 bar Max Internal Temperature: 130 °F / 54 °C Ignition Protected per SAE J1171 and ISO 8846: Rated IP67