Rod Holder Swivel Marine grade stainless steel and plastic

Backing Plate for 70 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders, or perhaps even tear through, causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and one for 80 series rod holders. Each size fits all 3 models of the series. Features: Use this backing plate for all 70 series rod holders (53670A, 53670CA, 53671A, 53671CA, 53672A, and 53672CA) 316L cast stainless steel 4" x 5-1/4" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Backing Plate for 80 Series Rod Holders Backing plates are very important to have under every rod holder used for heavy tackle fishing. When the rod holder is under extreme load, regular nuts and washers can concentrate stress and cause spider cracking around your rod holders or perhaps even tear through causing severe gunnel damage. Smith backing plates distribute mounting bolt pressure evenly over 30 times more surface area than with standard washers alone. 2 sizes, one for 70 series and 80 series rod holders. Each size fits all 3 models of the Series. Features: Use this backing plate on all 80 series rod holders (53680CA, 53680SA, 53681CA, 53681SA, 53682CA, and 53682SA) 316L cast stainless steel 4-1/4" x 6" 4mm thick Use your 1/4" stainless bolts and nuts (hardware not included)

Heavy Duty Pro Series Rod Holders The Pro Series line of molded rod holders takes the Pro Series to the next level with the addition of the Combo Mount. All the Pro-Series unique features you've come to expect, with the ability to mount in multiple configurations. Designed for use with casting and spinning rod holders. Heavy-duty, deep-tooth gear lock securely holds rod holder in mounting base. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

700A Series Rod Holder This rod holder is constructed of anodized aluminum and stainless steel for use in all freshwater and saltwater environments. More specifically, this rod holder is suitable for most walleye and panfish rods. An excellent choice for light trolling or still fishing. Features: Panther Rod Holders are designed and manufactured by CMP Group, the world’s leading producer of state-of-the-art boating and fishing equipment Posi-LOCK technology – 25 and 45-degree angles For optimum fishing performance, Panther gives you a full 360-degree hemisphere of possible positions The mounting base on all Panther models can be easily removed from the unit with an Allen Wrench for storage Panther Rod Holders are precision-made out of rust-resistant stainless steel and aluminum for freshwater and saltwater fishing 7 3/4 in. depth fits most standard rod sizes Mounting hardware is included Specifications: Base Plate (inch): 2-3/4" Tube Diameter (inch): 1-3/4" Tube Depth (inch): 7-3/4"

800A Series Rod Holder This rod holder is constructed of anodized aluminum and stainless steel for use in all freshwater and saltwater environments. This is Panther's most popular rod holder. It will accept most heavy-duty trolling rods and is the choice of serious anglers and charter captains throughout the Great Lakes as well as the Pacific Northwest. Features: Panther Rod Holders are designed and manufactured by CMP Group, the world’s leading producer of state-of-the-art boating and fishing equipment Posi-LOCK technology – 25 and 45-degree angles For optimum fishing performance, Panther gives you a full 360-degree hemisphere of possible positions The mounting base on all Panther models can be easily removed from the unit with an Allen Wrench for storage Panther Rod Holders are precision-made out of rust-resistant stainless steel and aluminum for freshwater and saltwater fishing 10 in. depth for larger fishing rods Mounting hardware is included Specifications: Base Plate (inch): 2-3/4" Tube Diameter (inch): 1-3/4" Tube Depth (inch): 10"

High Performance Electric Downrigger The High Performance Downrigger features a new illuminated digital line counter as well as the sleek new Rocket Launcher rod holder. Pre-spooled with the HP stainless steel downrigger wire, the HP models have unbeatle pulling power lifting 20 lb. weights with ease at 260 ft. / min, and 10 lb. weights at 312 ft. / min. Includes: 36" - 60" telescoping stainless steel boom. 1 1/4" dia. Illuminated, resettable, sealed and silent digital line counter 300 ft. of 180 lb. Test, 316 stainless steel downrigger wire 1/2" Kevlar drive belt by Optibelt TM - The same belts used by superior European auto manufacturers Clutch brake with the largest braking surface in the industry Boom mounted adjustable Rocket Launcher Rod Holder Swivel Pedestal Mount WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Cup Holder - 316 Stainless Steel Features: Stainless Steel Cup Holder @3.25ID Matches our ELITE Series Rod & Cup Holders Cutout Diameter: ø3.5” Flange Diameter: 4.75″ Ø1/2 Drain Barb Adhesive Tape / Gasket Installation – Included 316L Stainless Steel

No. 1101 Depthpower Downrigger (30") Designed for heavy duty use, this unit will handle long hours and heavy weights in tough conditions. PRODUCT OVERVIEW:  Fully adjustable decent speed, lifts 7 lb. weights at 235 ft./min. and 15 lb. weights at 203 ft./min. Spray protected positive-drive depth counter and Kevlar drive belt by Optibelt™ 250 ft. of 150 lb. Test, Stainless Steel Downrigger Cable Boom mounted adjustable 358 Rodmaster II Rod Holder Includes Scotty/Marinco™ Plug and Receptacle The lowest amperage draw of any downrigger made with less than 1/3 the battery draw than some of the competition Marine grade stainless steel boom Multi-position auto-stop included (Use 1008 Stopper Beads to stop at any pre-set position) Includes Power Grip Plus Line Release Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position Includes 1026 Swivel Pedestal Mount with 16 available positions Fully assembled and factory tested with complete saltwater protection Downrigger Boom Length: 30″ stainless steel boom Downrigger Boom Diameter: 1 1/4″ Rod Holder Interior Diameter: 1.85″ WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

No. 1106 The most popular Scotty Electric Downrigger, with a boom that telescopes for extra reach and collapses for storage. Makes for a great “big boat” downrigger. PRODUCT OVERVIEW:  Fully adjustable decent speed, lifts 7 lb. weights at 235 ft./min. and 15 lb. weights at 203 ft./min. Spray protected positive-drive depth counter and Kevlar drive belt by Optibelt™ 250 ft. of 150 lb. Test, Stainless Steel Downrigger Cable Boom mounted adjustable 358 Rodmaster II Rod Holder Includes Scotty/Marinco™ Plug and Receptacle The lowest amperage draw of any downrigger made with less than 1/3 the battery draw than some of the competition Marine grade stainless steel boom Multi-position auto-stop included (Use 1008 Stopper Beads to stop at any pre-set position) Includes Power Grip Plus Line Release Includes 1023 Tilt-up Mounting Bracket which enables the unit to be tilted and locked in the upright position Includes 1026 Swivel Pedestal Mount with 16 available positions Fully assembled and factory tested with complete saltwater protection Downrigger Boom Length: 36″-60″ telescoping stainless steel boom Downrigger Boom Diameter: 1 1/4″ Rod Holder Interior Diameter: 1.85″ WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Flush Mount Rod Holder, Standard Series 2" Diameter 7.5" Length Attwood stainless steel rod holders meet the need for the finest in finish, function and durability. Polished 316 grade stainless steel tube for corrosion-resistance Gasket Provides water seal around flange Optional, U.V. resistant, Cover Cap/Gasket closes tube when not in use U.V. resistant polymer liner protects finish on rod or reel WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Flush Mount Rod Holder, Standard Series 2" Diameter 7.5" Length Attwood stainless steel rod holders meet the need for the finest in finish, function and durability. Polished 316 grade stainless steel tube for corrosion-resistance Gasket Provides water seal around flange Optional, U.V. resistant, Cover Cap/Gasket closes tube when not in use U.V. resistant polymer liner protects finish on rod or reel WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Flush Mount Rod Holder, Standard Series 2" Diameter 7.5" Length Attwood stainless steel rod holders meet the need for the finest in finish, function and durability. Polished 316 grade stainless steel tube for corrosion-resistance Gasket Provides water seal around flange Optional, U.V. resistant, Cover Cap/Gasket closes tube when not in use U.V. resistant polymer liner protects finish on rod or reel WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Flush Mount Rod Holder, Standard Series 2" Diameter 7.5" Length Attwood stainless steel rod holders meet the need for the finest in finish, function and durability. Polished 316 grade stainless steel tube for corrosion-resistance Gasket Provides water seal around flange Optional, U.V. resistant, Cover Cap/Gasket closes tube when not in use U.V. resistant polymer liner protects finish on rod or reel WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Backing Plate For use with all Mate Series Rod and Cup Holders