Jacuzzi 05392204Rkit Impeller Kit  

Jacuzzi 05392303Rkit Impeller Kit  

Jacuzzi 24012205 Impeller For 7Rp2  

Jacuzzi 03063609R000 Case Kit  

Jacuzzi 24012304 Seal Kit  

Major Rebuild Kit for Sherwood J-70 This kit contains the following items   MS DATA SHEET 1 DATA SHEET SH 10515C 1 SCREW & WASHER SH 12211 2 BALL BEARING SH 12331 1 SET SCREW 1/4X20 3/8 SH 12622 1 NON ROK KEY SH 12710 3 LOCKWASHER SH 12857 3 SCREW SH 12859 1 SEAL/SEAT ASSEMBLY SH 15883 1 CAM BRASS SH 25150 1 WEAR PLATE SH 4258 3 SNAP RING (SMALL) SH 4259 2 SNAP RING (LARGE) SH 4264 1 WASHER SH 4432 1 KEY SH 5133 1 SPACER SH 9959K 1 IMPELLER KIT     Kits are put together at time of order

Minor Repair Kit for Sherwood J-70 This kit contains the following items   SH 12859 1 SEAL/SEAT ASSEMBLY SH 9959K 1 IMPELLER KIT     Kits are put together at time of order

Talulah Ballast Pump Impeller Kit  A worn or damaged impeller can cause system failure or engine breakdown. SPX's Johnson Pump brand impellers are developed and manufactured for maximum flow and long life. With a genuine spare impeller you can also be sure that you are getting the quality required by engine manufacturers and professionals.

Impeller Kit F3 Nitrile A worn or damaged impeller can cause system failure or engine breakdown. SPX's Johnson Pump brand impellers are developed and manufactured for maximum flow and long life. With a genuine spare impeller you can also be sure that you are getting the quality required by engine manufacturers and professionals. Features:  Made for F3B Pump Material: Nitrile (oil resistant) In The Product Box: Impeller Glycerine lubricate O-rings, gasket, and cover Dimensions: Outer Diameter: 1.78" Inner Diameter: 0.31"/Flat Width: 0.50" *F3B oil pump with reversible switch sold separately 

J-Walker 100 Saltwater Pro Pack Kit Berkley® combined the best of the renowned Berkley® J-Walker in a convenient 3-lure pro pack. The J-Walker features a sleek, tail-weighted design that has been refined to provide casting distances. The hydrodynamic shape, precision balance point, and resting position allow for an easy walk-the-dog action that has been proven on the water. Topped off with Fusion19TM hooks, Berkley® J-Walkers are sure to impress anglers of all skill levels. Features: Tail-weighted design tuned for casting distance Attractive, easy-to-start walking action that can be worked at a variety of speeds A tapered back adds flash and surface disturbance Ideal action and sound for a variety of top-water scenarios Upgraded with sharp 3X anti-rust Fusion19™ hooks Tail-weighted design tuned for casting distance Attractive, easy-to-start walking action that can be worked at a variety of speeds The tapered back adds flash and surface disturbance Ideal action and sound for a variety of top-water scenarios Upgraded with sharp 3X Anti-Rust Fusion19™ hooks Specifications: Color: Varies Bate Size: 100 (1/2 oz) Bait Weight: 1/2 oz Bait Length: 4.7 in. Hook Size: 4 Buoyancy: Floating Package Count: 3  Water Type: Saltwater

Impeller Kit Material:Neoprene Drive Type:Spline Drive Number of Blades:12 Dimensions: Diameter:2-1/4" Shaft Width:1-1/4" Shaft Diameter:5/8" Insert Material:Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit Material:Neoprene Drive Type:Spline Drive Number of Blades:12 Dimensions: Diameter:2-1/4" Shaft Width:5/8" Shaft Diameter:1-29/32" Insert Material:Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit Material:Neoprene Drive Type:Spline Drive Number of Blades:12 Dimensions: Diameter:3-3/4" Shaft Width:1" Shaft Diameter:2-9/16" Insert Material:Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit Material:Neoprene Drive Type:Spline Drive Number of Blades:12 Dimensions: Diameter:3-3/4" Shaft Width:1" Shaft Diameter:3-9/16" Insert Material:Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Impeller Kit Material:Neoprene Drive Type:Spline Drive Number of Blades:10 Dimensions: Diameter:2-9/16" Shaft Width:&#8541" Shaft Diameter:2" Insert Material:Brass Jabsco flexible impellers can be fitted to most makes and models of bronze flexible impeller engine cooling, bilge, transfer and general purpose pumps. Jabsco flexible impellers are subjected to rigorous quality processes to ensure reliable, efficient and long lasting performance. Replace all impellers at least once every year, or sooner, depending on the engine duty. When the installation is correct an impeller may last for several years, but it is always advisable to stick to a schedule of preventative, rather than corrective, maintenance. Replacing impellers is easy. By removing the end cover screws, it is possible to remove the impeller by using either a Jabsco Impeller Removal Tool, or channel lock pliers, to grip the hub of the impeller. Don?t use screwdrivers as they may damage the face of the pump body, causing leaks, and they can be dangerous in confined spaces. Always carry spare impellers on board in case of emergency. The impeller is one of the most vital components of the engine cooling system and should always be treated as such. Always grease new impellers. Firstly, it makes it easier to install the impeller into the pump bore, and secondly it gives added protection to the impeller during initial prime. After replacing the gasket and end cover the pump is ready to use. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.