|
Sealed Macerator
Self-Priming Macerator Pump with Run-Dry Protection
Waste Evacuation
The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation
It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.
Fish Box and Livewell Tank Evacuation
The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.
Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.
Features:
Impeller: Jabsco Nitrile compound
Macerator: Stainless Steel Cutter reduces particle size to 1/8" maximum. New 4 blade design
Seal: Lip Type
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
213.18 |
|
|
Jabsco 12460-0011 Self Priming Pump 12V
This item is 'build to order'. Please contact us for lead time.
|
538.60 |
|
|
Maxi Puppy 3000 12V Flexible Impeller Pump
Maxi Puppy self-priming pump 12VDC. Ports ½” BSP threaded (use ¾” hose adapters), plus connections for 25mm (1”) bore hose.
Features:
Connections: - for 25mm (1”) bore hose or 1/2" BSP
Dimensions: - 220mm long, 120mm wide, 85mm high
Fuse Size: - 25(amp)
Output: - up to 45 litres/minute (10 gallons/minute).
High capacity, continuously rated bilge pump
Self priming up to 2.4m vertical lift
Simple, fully serviceable design with few wearing parts
Can generate pressures up to 1 bar (15 psi)
Bronze body, stainless steel shaft
Packaged Dimensions: L:28.00 x H:13.00 x W:15.00cm
Actual Weight: 3.85 Kg (Approx. 4.35 Kg packed)
WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
426.20 |
|
|
Jabsco 12290 Series Self Priming Pump Phenolic
FEATURES
Pump Body: Phenolic Plastic
Port Size: 5/8" OD for Hose Connections
Flow: 5.8 GPM at 10 feet of head
Pressure: Up to 13 PSI
Impeller: Neoprene, Nitrile or Viton
Shaft Seal: Lip Type
Shaft: Shaft of Motor (Stainless Steel)
Motor: 115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector, Three-prong ground plug.
APPLICATIONS
A low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.
Jabsco Self Priming Pump 5/8" Hose Ports 115V ODP Motor Phenolic Head, Neoprene Impeller
|
808.67 |
|
|
Jabsco 12290 Series Self Priming Pump Phenolic
Pump Body: Phenolic Plastic
Port Size: 5/8" OD for Hose Connections
Flow: 5.8 GPM at 10 feet of head
Pressure: Up to 13 PSI
Impeller: Neoprene, Nitrile or Viton
Shaft Seal: Lip Type
Shaft: Shaft of Motor (Stainless Steel)
Motor: 115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector
Three-prong ground plug
APPLICATIONS
A low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.
Jabsco Self Priming Pump 5/8" Hose Ports 115V Totally Enclosed Motor Phenolic Head, Neoprene Impeller
|
907.92 |
|
|
Jabsco 12290 Series Self Priming Pump Phenolic
FEATURES
Pump Body:
Phenolic Plastic
Port Size:
5/8" OD for Hose Connections
Flow:
5.8 GPM at 10 feet of head
Pressure:
Up to 13 PSI
Impeller:
Neoprene, Nitrile or Viton
Shaft Seal:
Lip Type
Shaft:
Shaft of Motor (Stainless Steel)
Motor:
115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector, Three-prong ground plug.
APPLICATIONS / CHARACTERISTICS
Designed as a low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.
Jabsco Self Priming Pump 5/8" Hose Ports 115V Totally Enclosed Motor Phenolic Head, Viton Impeller
|
888.25 |
|
|
Gianneschi ACB80E-12V Bronze 12V Self-Prime Pump
Gianneschi ACB80E-12V, ACB Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Brass impeller, 316 Stainless Steel Shaft. Motor is 0.45KW (0.6 Horsepower), 2600 RPM, 12 Volts DC. Inlet Port is 3/4 Inch, Discharge Port is 3/4 Inch.
Applications for the ACB80E12V include chain washing, fire fighting, pumping seawater and liquids with a high gas content, diesel and oil pumping, bilges, and any water supplying applications.
|
1680.43 |
|
|
Jabsco 12290 Series Self Priming Pump Phenolic
Pump Body:
Phenolic Plastic
Port Size:
5/8" OD for Hose Connections
Flow:
5.8 GPM at 10 feet of head
Pressure:
Up to 13 PSI
Impeller:
Neoprene, Nitrile or Viton
Shaft Seal:
Lip Type
Shaft:
Shaft of Motor (Stainless Steel)
Motor:
115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector, Three-prong ground plug.
APPLICATIONS
Designed as a low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.
|
888.25 |
|
|
Jabsco 12490 Series Self Priming Stainless Steel Pump
FEATURES
Pump Body:
316 Stainless Steel
Port Size:
1" NPT internal
Flow:
26.0 GPM at 10 feet of head
Pressure:
Up to 26 PSI
Impeller:
Neoprene or Nitrile
Shaft Seal:
Lip Type in Stainless Steel Case
Shaft:
Steel motor shaft with special Stainless Steel sleeve.
Motor:
3/4 HP, 1725 RPM, 60 Hz Single Phase, 115/230 Vac, Continuous Duty, Totally Enclosed Fan Cooled, 56 Frame, Capacitor Start. Thermal Overload Protection with Automatic Reset, Carrying Handle, 6' Cord with 3 Prong Grounded Plug.
APPLICATIONS / CHARACTERISTICS
CHEMICAL - Industrial Motor Pump Unit Circulating, Transferring and Filtering of Chemicals, Plating Solutions, Pharmaceuticals, cosmetics and Farm Chemicals, Emptying and Filling Carboys, Vats, Tanks, Barrels or Entire Systems.
Jabsco Self Priming Stainless Steel Pump 1" NPT Ports 3/4HP Motor Nitrile Impeller
|
2303.80 |
|
|
Jabsco 14900-0001 Self Priming Pump 115V
This item is 'build to order'. Please contact us for lead time.
|
738.62 |
|
|
MP Pumps 21311 Flomax 5, 1-1/2" pedestal mount self priming pump
MP Pumps Flomax 5, rated at 100 GPM in bronze construction with viton mechanical seal.
Specifications
Rated Capacity 100 GPM Maximum
Discharge Pressure: 40 PSI
Suction & Discharge Connections: 1-1/2" X 1-1/2" FNPT
Construction: Bronze housing, impeller, removable suction & discharge flanges and wear plate; rubber check valve with 304 ss weight; 304 stainless steel stub shaft to fit either 5/8"; viton mechanical seal.
|
2960.96 |
|
|
AMT Pump 368B-95 Strt Cent Pmp Iron 1/2Hp
Engine/Motor Type: Total Enclosed Fan Cooled
Horsepower: 0.5 HP
Phase: Single-Phase
Pump Voltage: 115 Volt (Single-Phase), 230 Volt (Single-Phase)
Frequency: 60 Hz
Rated Current: 9/5 Amps
Pump RPM: 3450
Thermal Overload Protect: Yes
Motor Frame: 56J
Pump Type: Straight Centrifugal Pump
Pump Style: Electric Centrifugal Pump
Inlet Diameter: 3/4"
Outlet Diameter: 1/2"
Discharge Port Rotation: 90 Degree Increments
Max Gallon Per Min (GPM) : 38.0
Max Total Head (Static): 57 Feet
Maximum Pressure (PSI): 25
Max Working Pressure: 75 PSI
Solids Handling: Yes
Max Solids Handling (Inches): 0.125"
Self Priming Pump: No
Pump Housing Drain: Yes
Housing Material: Cast Iron
Impeller Type: Self-Cleaning, Semi-Open
Impeller Material: Stainless Steel
Seal Material (Mechanical Or Other): Buna-N
Temperature RangeTo 180 F
Port Type: NPT
Altitude Affected: Yes
|
510.48 |
|
|
Gianneschi ACB61E-12V Bronze 12V Self-Prime Pump
|
898.39 |
|
|
Run-Dry Macerator Waste Pump
WASTE EVACUATION
The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation
It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage.
FISH BOX AND LIVEWELL TANK EVACUATION
The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties.
Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats.
Triple sealed motor to prevent both internal and external motor corrosion
New Four-bladed chopper reduces clogging
Detects the absence of fluid then shuts-off pump before impeller is damaged
Sensor provides adequate run-dry period to allow initial priming of the pump
Interrupting power supply to the macerator resets the Run-Dry Device
Flow rate to 12 gpm
Self-priming to 4ft
Fitting:
Inlet Port: 1-1/2" Hose Barb plus 1-1/2 NPT
Discharge Port: 1" Hose Barb
WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.
|
226.09 |
|
|
Standard Electric Compact Macerator Style - 12V
The Johnson Pump Aqua Marine Toilet has been designed to meet virtually every conceivable lavatory installation situation onboard.
Priced competitively, the fine finish and well thought-through design of these toilets is remarkable. Made from white vitreous porcelain, and with corrosion resistant parts throughout, the Johnson Pump AquaT marine toilet, is quiet, robust and easy to clean.
Using the Johnson Pump Aqua Marine Toilet, water inlet and outlet takes place in two distinct steps. First the bowl is filled with clear water, and then the waste is flushed, leaving the bowl empty and clean, with no liquids sloshing about. Naturally, automatic back-flow prevention is incorporated into the design.
Most models can be ordered with standard, bevelled or low profiles in order to fit almost any hull and bulkhead configuration, and all are available in either compact or comfort versions so you can outfit your marine lavatory with the perfect-sized toilet, no matter what the layout.
The Aqua Toilet will give you years of trouble free operation. When spare parts such as a new seat or valve are needed, you'll find Johnson Pump's global network of distributors at your service.Power models are shipped with well-proven Aqua Jet diaphragm pumps.
It's probably fair to think of most toilets as commonplace products, but look at the features and you're sure to see that the Aqua is far from ordinary. Quiet, hygienic and reliable, the Johnson Pump AquaT marine toilet is perfect for almost any marine toilet room.
CE-approved
Features
Whisper quiet operation
Self-priming pump
One push button on control panel
Clean lines - pleasing to the eye
Hygienic, easy-to-clean vitreous china bowl and exterior surfaces
Robust wooden seat with durable baked enamel finish
Low water consumption (2-2.5 l/flush) makes the most of holding tank capacity
Versatile plumbing connection options
Automatic back-flow prevention
Available in comfort or compact bowl sizes
Designed for virtually any onboard mounting position
May be installed above or below the waterline
Suitable for OEM or replacement installation
Corrosion resistant materials throughout
Long service life
Equipped with 12V Aqua Jet pumps
Quick-connect hose or threaded connectors
Complies with ISO 8846, ignition protection, and EN 55014 EMC
|
303.71 |
|