Puck Transducer Description: Puck transducer . Single/Dual Beam, 20/60 degree, 200/83 kHz with built in temperature For Use With: Legend ID40, Piranha 5, PiranhaMax 10, PiranhaMax 15, PiranhaMax 20, Matrix 15, Matrix 17, Matrix 25, Matrix 27, Matrix 55, Matrix 65, Matrix 67, Matrix 97, FF515, FF535, FF565. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XP 9 HW T In-Hull Transducer Features: In-Hull 9-Pin High Wide Hardware included WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Dual HELIX® Starter Kit HWFG - In Hull This kit provides brings it all together- quick and easy. Everything you need to network two Ethernet-equipped HELIX models on a fiberglass boat is included. Additionally, this kit connects the included in hull Dual Spectrum CHIRP transducer with an existing Side/Down Imaging® transducer via the enclosed splitter cable, and includes an adapter cable to connect compatible HELIX 8, 9, 10, 12, 15 MEGA Imaging® units to select Minn Kota® motors with Built-In MEGA Imaging®.  Features: Kit Includes: (1) XP 9 HW T in-hull mount Dual Spectrum CHIRP Transducer and epoxy, (1) AS EC 20E 20' Ethernet Cable, (2) AS EC QDE Ethernet Adapters, (1) MKR-MI-1 Built-In MEGA Imaging HELIX Adapter, (1) 9 M SIDB Y Transducer Splitter Cable Compatible with: HELIX 8 G3N/G4N Series, HELIX 9 G2N/G3N/G4N Series, HELIX 10 G2N/G3N/G4N Series, HELIX 12 G2N/G3N/G4N, HELIX 15 G4N Series 1-Year Limited Warranty

Active Imaging 2-in-1 Transducer & 83/200 Pod In-Hull Transducer with Y-Cable  Allows for connection of an in-hull puck transducer and an Active Imaging 2-in-1 (Side/Down) transducer to the single sonar port of an Elite Ti2 or Elite FS display. Features: Active Imaging 2-in-1 Transom Transducer 83/200 Pod/Puck Transducer without temperature Dual 9-pin Y-cable

Bronze Thru Hull Transducer Bronze Thru-Hull Transducers are for large boats and for boats with in-board motors that make typical Transom Mount Transducers ineffective. They are not recommended for trailered boats as the transducer is not flush with the hull. Bronze Thru-Hull Transducers require that a hole be drilled in the hull and the shaping of a fairing block. Professional installation is recommended. Plastic Thru-Hull Transducers are an alternative to Bronze Thru-Hull Transducers. Description: Bronze thru hull transducer, single or dual beam use. 20/60 degree, 200/83kHz. Transducer dimensions: 5.25L X 2.75"W X 1.2"D (below hull); Shaft diameter: .86". Fairing block not included. WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XTM 9 WIDE DI 20 T Trolling Motor Mount Transducer Low profile design minimizes snags. Easy installation and all hardware is included. Features: Trolling Motor Transducer Down Imaging® Transducer 200/455kHz Low Profile Design Minimizes Snags Easy Installation All Hardware Included Built-in temperature 15' cable Compatibility: 1100 Series™: 1158c DI Combo 900 Series™: 958c DI Combo 800 Series™: 858c DI Combo WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

M260 In-Hull 1kW Transducer with No Connector In-hull features, thru-hull performance. Setting the In-Hull Standard It's true! Excellent performance can be achieved from an in-hull mounted transducer. The M260, Airmar's 1 kW in-hull, is designed with Airmar's exclusive Broadband Ceramic Technology. The 200 kHz element provides broadband performance resulting in higher resolution without sacrificing sensitivity. Combined with a seven-element 50 kHz array, this in-hull has excellent. All-Out Fishfinding Performance! Optimal fishfinder performance no longer requires drilling a hole in the hull! The M260 is able to transmit and receive through solid fiberglass while displaying sharp detailed images. Track the bottom at speeds exceeding 30 knots! Installation simply requires adhering the tank to the inside of the vessel, leaving a clean and smooth hull exterior! Features M260 Transducer with In-Hull Kit 1,000 Watts Power 50/200 kHz w/Diplexer 19/6 degree Beam Angles Interfaces to any 600W or 1kW echosounder Recommended for solid fiberglass hulls Innovative tank design allows for bow-stern or port-starboard mounting Available with a diplexer for single transmission line fishfinders and without a diplexer for dual transmission line fishfinders Mineral oil or non-toxic anti-freeze (propylene glycol) is used to fill the tank Transducer ID™ feature WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Low/High Frequency - In-Hull Chirp Transducer without Connector Rely on Airmar's new broadband transducers for your ultimate fishing mission. Whether you're a commercial fisherman, charter captain, or tournament angler, there's a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000') with 5 to 10 times greater detail and resolution so precise it_s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 112 kHz of total bandwidth in just one installation, saving customers time and money. As the ELITE model in the Chirp In-Hull product line, the R599 LH Chirps across the following bandwidths: LH Model - Low Frequency 28-60 kHz/High Frequency 130-210 kHz Features: Depth only Low-CHIRPS from 28 kHz to 60 kHz 23° to 9° beamwidth High-CHIRPS from 130 kHz to 210 kHz 8° to 4° beamwidth 112 kHz of total bandwidth from one transducer Covers popular fishing frequencies of 28, 38, 50, and 200 kHz plus everything else in the bandwidth Fishing Profile: Recreational and commercial inshore and offshore fishing (deep-water canyon and sea-mount tracking) Epoxy transducer housing Hull Type: Solid fiberglass only Specifications: Hull Deadrise: 0° to 22° Acoustic Window: Epoxy/urethane All mounting hardware provided, including tank Weight: 19.7 kg (43.4 lb) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

M265LH Plastic In-Hull Mount Transducer w/Depth - 12-Pin Garmn's best performing 1 kW in-hull, this narrow beam transducer provides crisp image detail. The transducer has a depth of 3,000 feet; an operating frequency of 42 to 65 kHz and 130 to 210 kHz; a beamwidth of 16 to 25 degrees or 6 to 10 degrees; and a 0 to 30 degree deadrise. Transducer kit comes with installation instructions. Follow the instructions carefully to avoid damaging your boat. *Not recommended for cored-hull vessels Compatible Devices: GPSMAP® 7607xsv, 7608xsv, 7610xsv, 7612xsv, 7616xsv GSD™ 25 Premium Sonar Module WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

R599 Low/Med Frequency In-Hull Chirp Transducer - Bare Wire Rely on Airmar’s broadband transducers for your ultimate fishing mission. Whether you’re a commercial fisherman, charter captain, or tournament angler, there’s a new game in town! Chirp transducers enable bottom detection down to 3,000m (10,000’) with 5 to 10 times greater detail and resolution so precise it’s possible to distinguish between individual baitfish, game fish, and underwater structures. One transducer delivers up to 102 kHz of total bandwidth in just one installation, saving customers time and money. As the ELITE model in the Chirp In-Hull product line, the R599LM Chirps across the following bandwidths: LM Model - Low Frequency 28-60 kHz/Medium Frequency 80-130 kHz. Features: Depth Only Chirp Technology L/M Frequency 2-3 kW High-Performance Epoxy 25 internal ceramics Exclusive Xducer ID® technology Specifications: Hull Deadrise: 0° to 22° Acoustic Window: Epoxy/urethane All mounting hardware provided, including tank Weight: 19.7 kg (43.4 lb) This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

CPT-S In-Hull CHIRP Transducer The CPT-S In-hull transducer provides a simple-to-install depth only transducer solution for non-cored fiberglass hulls. Ideal for sailing, cruising, and small powerboat applications, the CPTS-S In-hull transducer supports CHIRP sonar operation centered on 200kHz.  The CPT-S in-hull directly connects to Element S series units. Will connect to Axiom RV/Axiom Pro RVX and Element HV using the A80490 (Axiom) or A80559 (Element HV) adapters. An innovative transducer tube housing design allows the CPT-S In-Hull to mount in hulls ranging from 0 to 25 degrees deadrise.

XP-14-HW-T Dual Spectrum CHIRP In-Hull Transducer with Temp for SOLIX™ In-Hull Dual Spectrum CHIRP Transducer supports Dual Spectrum CHIRP 2D Sonar with high frequency beam and wide cone angle, offering CHIRP range of 150-220kHz and max depth of 1200ft. Intended for glue-in installation inside single layer fiberglass hulls. Includes built-in temperature sensor, epoxy kit and 20’ cable.  Features: This accessory is compatible with the following Humminbird products: SOLIX® 10, 12, 15 – All G2 Models. Side Imaging™ and Down Imaging™ units can support the XP 14 HW T as a 2D sonar only transducer. This transducer does not support Side Imaging or Down Imaging. Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz DUAL Spectrum CHIRP Max Depth: 1200ft (365m) WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XP 9 HW In-Hull Transducer In-Hull Dual Spectrum CHIRP Transducer supports Dual Spectrum CHIRP 2D Sonar with high frequency beam and wide cone angle, offering CHIRP range of 150-220kHz and max depth of 1200ft. Intended for glue-in installation inside single layer fiberglass hulls. Includes epoxy kit and 20’ cable.  Features: This accessory is compatible with the following Humminbird products: HELIX 5 CHIRP G2 – GPS-equipped models only, HELIX 7 CHIRP G2/G3 – GPS-equipped and CHIRP DI G2 models, HELIX 7 CHIRP G2N/G3N – All models, HELIX 8 CHIRP G3N – All models, HELIX 9 CHIRP G2N/G3N – All models, HELIX 10 CHIRP G2N/G3N – All models, HELIX 12 CHIRP G2N/G3N – All models, ICE HELIX CHIRP G2 – All models (In Open Water Mode). Side Imaging™ and Down Imaging™ units can support the XP 9 HW as a 2D sonar only transducer. This transducer does not support Side Imaging or Down Imaging. Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz Dual Spectrum CHRIP Max Depth: 1200ft (365m) WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XPTH 9 20 MSI T MEGA Plastic Thru-Hull Transducer MEGA SI, MEGA DI, DualBeam PLUS, 20/60/86/55 degrees, 200/83/455/800 kHz and 1.2 MHz. Temperature built-in, plastic through the hull transducer. 30' cable Transducer dimensions:  7.34"L x 3"W Shaft diameter:  1.0" WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

XPTH-9-HW-T Dual Spectrum CHIRP Plastic Thru-Hull Transducer with Temp  Plastic Thru-Hull Dual Spectrum CHIRP Transducer supports Dual Spectrum CHIRP 2D Sonar with high frequency beam and wide cone angle, offering CHIRP range of 150-220kHz and max depth of 1200ft. Includes built-in temperature sensor, rugged composite design and 30’ cable.  Features: This accessory is compatible with the following Humminbird products: HELIX 5 CHIRP G2 – GPS-equipped models only, HELIX 7 CHIRP G2/G3 – GPS-equipped and CHIRP DI G2 models, HELIX 7 CHIRP G2N/G3N – All models, HELIX 8 CHIRP G3N – All models, HELIX 9 CHIRP G2N/G3N – All models, HELIX 10 CHIRP G2N/G3N – All models, HELIX 12 CHIRP G2N/G3N – All models, ICE HELIX CHIRP G2 – All models (In Open Water Mode). Side Imaging™ and Down Imaging™ units can support the XPTH 9 HW T as a 2D sonar only transducer. This transducer does not support Side Imaging or Down Imaging. Dual Spectrum CHIRP Frequencies: Full: 150-220 kHz, Narrow: 180-240 kHz, Wide: 140-200 kHz Dual Spectrum CHRIP Max Depth: 1200ft (365m) WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.