|
Gianneschi ACB331-230V Bronze 230V 1Ph 50/60Hz
Main pump features:
Outstanding self-priming
Side channel and liquid ring construction
Simple and compact
Applications:
Ballast
Bilge
Diesel oil
F.W./S.W. Washing
Fire-fighting
S.W feeding
WPS - Hydrofore
Port Size: From 1'' 1/4 to 1'' 1/2 BSP
Pump casing: Bronze
Impeller / Gear: Bronze
Shaft: Stainless steel
|
4321.65 |
|
|
Gianneschi CB 22-120 0.75KW Cent Pump 230V 50/60Hz 1Ph
Gianneschi CB-22-120-230V, CB Series Centrifugal Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 0.55 KW (0.75 Horsepower), 2900 RPM, 230 volts AC, Single Phase. Inlet Port is 1 Inch BSP Inlet, Discharge Port is 1 Inch BSP Outlet.
Applications for the CB 22-120-230V include air conditioning systems, water supply, lifting fresh or salty water at sanitary plants, water circulations, increasing water pressure at water plants, pumping fresh water and seawater, and cooling and heating. Before installation, ensure that mains supply is grounded in accordance with local legislation and corresponds to motor plate detail.
|
1694.69 |
|
|
Gianneschi CB 22-95 0.55KW Centrifugal Pump 230V 50/60Hz 1Ph
Gianneschi CB-22-95-230V, CB Series Centrifugal Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 0.37KW (0.5 Horsepower), 2900 RPM, 230 volts AC, Single Phase. Inlet Port is 1 Inch BSP Inlet, Discharge Port is 1 Inch BSP Outlet.
Applications for the CB2295230V include air conditioning systems, water supply, lifting fresh or salty water at sanitary plants, water circulations, increasing water pressure at water plants, pumping fresh water and seawater, and cooling and heating.
|
1416.18 |
|
|
Gianneschi CB 22-110 0.55KW Cent Pump 230V 50/60Hz 1Ph
Main pump features:
High performance with limited power needed
Open or close impeller available
Threaded/Flanged connection
Wide range
Applications:
F.W./S.W. Circulation
S.W feeding
WPS - Hydrofore
Port Size: From 1/2'' to 1'' 1/2 BSP - from DN32 to DN65
Pump casing: Bronze
Impeller / Gear: Bronze
Shaft: Stainless steel
|
1848.19 |
|
|
Gianneschi CB 22-120 1.1KW Cent Pump 230V 50/60Hz 1Ph
Main pump features:
High performance with limited power needed
Open or close impeller available
Threaded/Flanged connection
Wide range
Applications:
F.W./S.W. Circulation
S.W feeding
WPS - Hydrofore
Port Size: From 1/2'' to 1'' 1/2 BSP - from DN32 to DN65
Pump casing: Bronze
Impeller / Gear: Bronze
Shaft: Stainless steel
|
1961.88 |
|
|
Gianneschi BMA 50/160 B1 Motor and Pump 230V 1Ph
Gianneschi catalog # BMA-50/160-B1-230V-, BMA Series Self Priming Centrifugal Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 2.2 KW (3 Horsepower), 2900 RPM, 230 volts AC, 50/60 Hz, Single Phase.
Applications for the BMA50/160B1230V include chain washing, air conditioners, emptying operations, bilges, cooling systems, OEM, fire fighting, ballasts, gray water systems, as well as swimming pool filling.
|
4800.04 |
|
|
Gianneschi KACB33102C Repair Kit For ACB331 230V
|
748.86 |
|
|
Gianneschi ACB80E-230V Mpu 230V 60Hz
Gianneschi ACB80E-230V, ACB Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Brass impeller, 316 Stainless Steel Shaft. Motor is 0.37kW (0.5 Horsepower), 2900 RPM, 230 Volts AC, Single Phase. Inlet Port is 3/4 Inch, Discharge Port is 3/4 Inch.
Applications for the ACB80E230V include the pumping of liquids with high gas content or seawater, as well as in chain washing, oil and diesel, fire fighting, bilges, and water supplying.
|
1273.96 |
|
|
Gianneschi KACB33102 Repair Kit For ACB331
|
313.46 |
|
|
Gianneschi CP26-A1-110V 60HZ Bronze Self Priming Pump
Gianneschi CP-26-A1-110V, CP Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 0.37KW (0.5 Horsepower), 1450 RPM, 110 volts AC, 60 Hz, Single Phase. Inlet Port is 1 Inch, Discharge Port is 1 Inch.
Pump Body: Bronze
Impeller: Bronze
Shaft: 316 Stainless Steel
Port Size: Inlet Port is 1 Inch, Discharge Port is 1 Inch
Motor Specs :0.37KW (0.5 Horsepower), 1450 RPM, 110 volts AC, 60 Hz, Single Phase.
|
1643.02 |
|
|
Gianneschi CP30-A2-110V 60HZ Brz Self Prim Pmp 110V 60Hz
CP Series Self Priming Liquid Ring Pump and Motor unit, Bronze construction, Bronze impeller, 316 Stainless Steel Shaft. Motor is 0.37KW (0.5 Horsepower), 1450 RPM, 110 volts AC, 60 Hz, Single Phase. Inlet Port is 1 Inch, Discharge Port is 1 Inch.
Features:
Body Pump: Bronze
Impeller: Bronze
Shaft: 316 Stainless Steel
Port Size: Inlet Port is 1 Inch, Discharge Port is 1 Inch
Motor Specs: 0.37KW (0.5 Horsepower), 1450 RPM, 110 volts AC, 60 Hz, Single Phase
|
1814.26 |
|
|
Gianneschi CP26-A1-230V Bronze Self Priming Pump
Gianneschi CP-26-A1-230V, CP Series Self Priming Liquid Ring Pump and Motor unit.
Pump Body: Bronze
Impeller: Bronze
Shaft: 316 Stainless Steel
Port Size: Inlet Port is 1 Inch, Discharge Port is 1 Inch
Motor Specs :0.37KW (0.5 Horsepower), 1450 RPM, 110 volts AC, 60 Hz, Single Phase.
|
1730.48 |
|
|
March 0130-0178-0100 Marine Pump LC-3M-MD
March Pump’s industrial LC-3M-MD is an American submersible seal-less centrifugal magnetic drive marine pump. It is capable of generating a maximum flow of 8.5 gallons per minute at 4 feet, and its maximum head is 19 Feet (8PSI). The LC-3M-MD pump may be used submerged or not submerged. The pump is Ignition Protected per SAE J1171 and ISO 8846, and has extended run dry protection thru the use of a carbon bushing. It is capable of 24,000 BTU a hour.
System: 230v 50/60Hz
Max Flow: 31 LPM
Max Head: 4.3 M
Power: 0.037 KW
Electrical/Air: 230V 50/60Hz
230V Motor
6 Foot Cord, Submersible
60Hz: 1Ph 0.05HP/0.037kW, 1 AMPS, 3450 RPM
50Hz: 1Ph 0.05HP/0.037kW, 1 AMPS, 2850 RPM
Inlet: 3/4"FPT
Outlet: 1/2"MPT
Submersible: Yes
Wet End: Polypropylene (Front and Rear Housing, Impeller), Cupric Nickel (Cooling Tube), Buna N (O-Ring, Cooling Tube Seal), Carbon (Impeller Bushing) Ceramic (Shaft, Thrust Washer), Ceramic Magnet
Uses: Submersible or Open Air
When submerged, the following is also in contact with the solution: Epoxy, Stainless Steel, Polysulfone, Cord
Max Internal Pressure: 25 PSI / 1.7 bar
Max Liquid Temperature: 130 °F / 54 °C
Ignition Protected per SAE J1171 and ISO 8846: Rated IP 67
UL Listed Motor:
Note: Product image may be different than actual product received.
|
430.95 |
|
|
March 0150-0250-0100 Marine Pump LC-5M-MD
March Pump’s industrial LC-5M-MD is an American submersible seal-less centrifugal magnetic drive marine pump. It is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (11PSI). The LC-5M-MD pump may be used submerged or not submerged. It is capable of 45,000 BTU a hour.
Max Flow: 54.9 LPM
Max Head: 8.2 M
Power: 0.093 KW
Electrical/Air: 230V 50/60Hz
230V Motor
6 Foot Cord, Submersible
60Hz: 1Ph 0.125HP/0.0093kW, 0.9AMPS, 3450 RPM
50Hz: 1Ph 0.125HP/0.0093kW, 0.5AMPS, 2850 RPM
Inlet: 1"FPT
Outlet: 1/2"MPT
Submersible: Yes
Wet End: Polypropylene (Rear Housing, Impeller), Noryl (Front Housing) Buna N (O-Ring, Cooling Tube Seal), 316 Stainless Steel (Shaft, Cooling Tube), Carbon (Impeller Bushing), Ceramic (Thrust Washers), Ceramic Magnet
Uses: Submersible or Open Air
When submerged, the following is also in contact with the solution: Epoxy, Noryl, Cord
Max Internal Pressure: 25 PSI / 1.7 bar
Max Liquid Temperature: 130 °F / 54 °C
Ignition Protected per SAE J1171 and ISO 8846: Rated IP67
This pump is capable of generating a maximum flow of 15 gallons per minute at 2 feet, and its maximum head is 27 Feet (11PSI). It is capable of 45,000 BTU a hour. The LC-5C-MD pump may be used submerged or not submerged. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Noryl, Buna N, Stainless Steel, Carbon, Ceramic, and Ceramic Magnet. When submerged, Epoxy, Noryl, and the Cord are also in contact with the solution. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 130 Fahrenheit or 54 Celsius.
The pump is Ignition Protected per SAE J1171 and ISO 8846. The impeller has a carbon bushing allowing the pump to run dry longer before suffering damage.
|
1101.60 |
|
|
March 0150-0040-1000 Magnetic Drive Pump AC-5M-MD
March Pump’s industrial AC-5M-MD is an American seal-less centrifugal magnetic drive pump ideal for applications such as chemical recirculation, chemical transfer, and scrubber systems. It is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (11PSI). The pump is Ignition Protected per SAE J1171 and ISO 8846, and has extended run dry protection thru the use of a carbon bushing. It is capable of 48,000 BTU a hour.
Max Flow: 64.4 LPM
Max Head: 8.2 M
Power: 0.093 KW
Electrical/Air: 230V 50/60Hz
Motor
3 Foot Cord
60Hz: 1Ph 230V 0.125HP/0.093kW, 2.1 AMPS, 3450 RPM
50Hz: 1Ph 230V 0.125HP/0.093kW, 1 AMPS, 2850 RPM
Inlet: 1"FPT
Outlet: 1/2"MPT
Wet End: Polypropylene (Rear Housing, Impeller), Noryl (Front Housing) Buna N (O-Ring), 316 Stainless Steel (Shaft), Carbon (Impeller Bushing) Ceramic (Thrust Washers), Ceramic Magnet
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 190 °F / 87 °C
Ignition Protected per SAE J1171 and ISO 8846: UL Listed Motor
This pump is capable of generating a maximum flow of 17 gallons per minute at 1 feet, and its maximum head is 27 Feet (11PSI). It is capable of 48,000 BTU a hour. The standard wet end (the materials that come into contact with the solution) is composed of Polypropylene, Noryl, Buna N, Carbon, 316 Stainless Steel, Ceramic, and Ceramic Magnet. The inlet connection is 1 inch female pipe thread, and the outlet is 1/2 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.125 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The maximum internal pressure the pump can tolerate is 50PSI, and the maximum liquid temperature is 190 Fahrenheit or 87 Celsius.
The pump is Ignition Protected per SAE J1171 and ISO 8846. The impeller has a carbon bushing allowing the pump to run dry longer before suffering damage.
|
488.50 |
|