Infrared Beam Sensor with 33' Cable The Infrared Beam Sensor can be mounted near entry points or in a cabin. These sensors use a true photoelectric beam, not an infrared field of view like our ePIR or Infrared Motion Sensor, which ensures protection against false alarms due to shadows, sunlight, etc.

Fuel Flow Sensor with 10' cable & T-connector Fuel Flow Sensor Gasoline ONLY. 1 required per engine. Up to 3 engines supported. Outputs: Fuel Flow Tank Fuel Used Trip Fuel Used Seasonal Fuel Used Cable Length: 10' Fuel Line Diameter: 3/8" (9.5mm) Inside Diameter Flow Rate Measured: Optimized for 0.6-45 Gal/hr but can measure outside these values Added Back Pressure to the fuel system: 0.5 PSI at 20 Gal/hr; 1 PSI at 40 Gal/hr Installation Location: Above the max level of the fuel tank, in-line after the fuel filter and any Y's or T's in the line Package: The Fuel Flow Sensor, N2K T and 2 (two) 1" hose clamps Fuel Type: Gasoline only. The Fuel Flow Sensor does not operate diesel engine fuel systems Hole required to route through a bulkhead: 22mm (7/8") Multiple Fule Flow sensors possible: Yes

WS310 Wired Wind Sensor with 35M Cable with Interface Cable The WS310 wind sensor pack is the perfect solution for any sailor looking to get accurate and fast wind data to your instruments from a wired wind sensor. High Performance Designed to provide highly accurate wind data in all conditions at all points of sail and heel. Reliability Thousands of hours of real-life testing have proved this instrument to be exceptional in all conditions. Providing fast and accurate data at all times. Comes with: WS310 Wind Sensor - 000-14391-001 WS310 (wired) Interface - 000-14389-001  WS300 35M (115') CABLE - 000-14397-001

NT-Evolution Security Hard Wired Package with OB Cowling Sensor GOST gives users the power to know the location of the boat and whether it's safe, secure, and ready to enjoy. Affordable, easy to install, and simple to use, GOST is the perfect solution for connecting boaters with the vessel. Features: Top-of-the-line, globally capable wired security, monitoring, and satellite tracking system designed specifically for harsh marine environments Real-time GPS location tracking GOST IDP 100x message size capacity What's Included DOOR / HATCH / ENG. COWLING | GDC - EXT - WGHD  Is the GOST standard door and hatch contact used inside the vessel? It is also used for engine cowlings.  Beam Sensor | GNT IBS 1 Is an infrared beam sensor designed to protect the exterior perimeter of the vessel. When the beam between the emitter and receiver is broken, the siren will alarm. High Water Sensor| GMM HWS Includes the bracket and the float switch that will be installed in the bilge of the vessel slightly below the vessel factory-installed high water sensor. Remote Keyfob | GMM KF2 Compact water-resistant design with a backlight for buttons and auditory feedback for arming or disarming a security system. The keyfob performs up to 6 actions per remote control, with a range of up to 150 feet. Water Resistant Strobe | GA STROBE WHITE Ultra small, self-contained semi-hemispheric white LED lights Surface or internal mount featuring 25 scan lock flash patterns, including synchronize feature for alternating or synchronous flashing. Mini Siren | GA-MINI-SIREN GOST Acoustics mini water-resistant, super-loud multi-tone marine siren, 125 db, 20 watt. Wired Sensors | Zone Hatch | Z2 (NC) Beam-Seansor | Z3 (NC) Engine Cowling | Z4 (NC) High Water | Z5 (NO) ComBUS | Four-Wire

NT-Evolution Security Hard Wired Package GOST gives users the power to know the location of the boat and whether it's safe, secure, and ready to enjoy. Affordable, easy to install, and simple to use, GOST is the perfect solution for connecting boaters with the vessel. Features: Top-of-the-line, globally capable wired security, monitoring, and satellite tracking system designed specifically for harsh marine environments Real-time GPS location tracking GOST IDP 100x message size capacity  What's Included 110 AC Power Out | GNT IP68 110AC POWEROUT HW Waterproof, 110 AC monitoring of vessel shore power. Door/Hatch | GDC EXT WGHD Water-resistant door and hatch contact are used to secure vessel access points. Beam Sensor | GNT IBS 1 Is an infrared beam sensor designed to protect the exterior perimeter of the vessel. When the beam between the emitter and receiver is broken, the siren will alarm. High Water Sensor| GMM HWS Includes the bracket and the float switch that will be installed in the bilge of the vessel slightly below the vessel factory-installed high water sensor. Remote Keyfob | GMM KF2 Compact water-resistant design with a backlight for buttons and auditory feedback for arming or disarming a security system. The keyfob performs up to 6 actions per remote control, with a range of up to 150 feet. Water Resistant Strobe | GA STROBE WHITE Ultra small, self-contained semi-hemispheric white LED lights Surface or internal mount featuring 25 scan lock flash patterns, including synchronize feature for alternating or synchronous flashing. Mini Siren | GA-MINI-SIREN GOST Acoustics mini water-resistant, super-loud multi-tone marine siren, 125 db, 20 watt. Wired Sensors | Zone: Hatch | Z2 (NC) Beam-Sensor | Z3 (NC) 110 AC Power Out | Z4 (NC) High Water | Z5 (NO) ComBUS | Four-Wire This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Wired Infrared Motion Sensor The Visonic 360 Ceiling Dualtech motion sensor offers robust protection against theft. Simply mount this sensor in a cabin or above the main entryway, and receive notification in the event of unauthorized entry. The sensor can also be programmed to sound an audible alarm. Featuring a sleek, compact, and elegant design, the sensor blends seamlessly into any décor. Visonic technology assures high reliability, false alarm immunity, and 360-degree coverage. Ideal for monitoring unexposed areas such as pilothouse, galley, cabin, etc. Specifications: Dimensions: 3.37in (diameter) 1in (depth) Ceiling Mount Range:  360° detection pattern with floor coverage up to 36ft Supply Voltage: 9-12V Not recommended for use on weather/exposed decks Works with MTC and Siren 3 Pro

Detachment Pull Sensor with 25' Lead Water Resistant Detachment Sensor with 25′ Lead.

608 Wind Sensor Without Cable Networked wind sensor for Triton2, Triton, IS42, IS40 and IS20 systems. Sensor only, does not include cable. Compatible with previous 508 and IS20 wind sensor mast cables and brackets.

1815 8.4" Color LCD 19" 4kW Radar with 10M Cable The Furuno 1815 is a standalone Radar package that features an 8.4” color LCD screen and stylish, low-profile 4kW radome antenna. It is designed for a wide variety of vessels, including pleasure craft, workboats and small fishing boats that require an easy-to-use, true color Radar at an affordable price point.The unit allows you to select from several adjustable display colors to ensure that it can be viewed in a variety of conditions. The gimbal mount allows the display to swivel when desktop mounted, allowing the user to adjust the display angle for optimal viewing comfort. Overhead mounts are available for added flexibility or you can flush mount it with a simple 5” hole saw. Furuno’s Fast Target Tracking (TT) function allows the user to manually or automatically track up to 10 targets. After selecting a target, it takes only seconds for a speed and course vector to be displayed, making quick work of determining the safety of approaching or moving targets. When using Furuno’s proprietary True Trail mode, moving objects will show a gradation of target trails in their wake, making it possible to gauge the movement of targets at-a-glance. Whenn connected to a Furuno AIS, up to 100 targets can be tracked and displayed on the screen, allowing the operator to instantly gather important information about other AIS-equipped vessels nearby.  The 1815 also utilizes Furuno’s True View mode to make reading the display more intuitive. For example, when your vessel is turning, the echoes stay consistent on the display, so you can constantly see the targets on the screen, without waiting for them to update after the turn. This mode proves to be especially useful when you are turning to avoid hazardous targets.  The automatic gain reduction on the 1815 makes use of algorithms that have been refined over many decades of Furuno experience and innovation. This means the 1815 is second to none in clutter rejection. With no input from the user, this Radar will automatically eliminate unnecessary echoes and present a clear display image with every sweep of its antenna. This ensures that you will be able to acquire other vessels, buoys and objects on the sea surface in good weather, or when sudden fog and storms make the visibility poor.  Other display modes include Off Center, allowing own ship's position to be shifted to a pre-registered point on screen, and Zoom, which will expand and display a selected target up to 2x in a zoom window. Features: •8.4" Portrait Color LCD Display (IPx6 Rating) •Compact and Lightweight 4kW Radome Antenna •Fast Target Tracking provides instant heading and speed info for up to 10 targets •True Trail and True View modes (heading sensor required) •AIS display for up to 100 targets (optional AIS receiver required) •Advanced auto-adjust settings for Gain/Sea Clutter/Rain Clutter •Digital Signal Processing for improved auto Gain/Sea/Rain controls •Cosmetic match to FCV588 Fish Finder with UI based on 1835 & FR8XX5 Radars •Swivel mount bracket to adjust the angle of the display unit •12-24 VDC input and low power consumption (Up to 38 W during transmit) •5.2-degree horizontal and 25-degree vertical beam width •External pigtail cable eliminates need to open the dome to install the Radar cable •(3) NMEA0183 inputs for GPS, heading, and AIS (Port 3 for heading only) •(2) NMEA0183 outputs for TTM, TLL and RSD (with required nav sensor inputs) Advanced Auto Adjust settings for Gain/Sea clutter/Rain clutter - To display targets clearly and accurately, the gain must adjusted. The 1815 can do this automatically for you. By automatically adjusting the gain, the Radar eliminates unnecessary echoes and display a clear image. Fast Target Tracking™ (TT) Function Fast Target Tracking™ (TT) function manually or automatically acquires and tracks 10 targets. After selecting a target, it only takes a few seconds for a speed and course vector to be displaed. With accurate tracking information, estimation of other vessel's course and speed is made easier. AIS Display  When connecting a Furuno FA-30/50 AIS unit, up to 100 AIS targets can be tracked and displayed on the Radar screen. The AIS improves safety during travel by sharing the status and position of your vessel with other AIS-equipped vessels nearby. You can easily read detailed information about other AIS equipped vessels nearby, such as speed and heading. True Trail Mode  When using the True Trail mode, moving objects will show up on the main screen with a gradational trail. These trails make it possible to see the movement of nearby vessels in the blink of an eye. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

xSonic R509LH-W Thru-Hull Wide-Beam CHIRP w/Fairing Block Get more coverage under the boat with Airmar's new wide beam Chirp product line. Offering a high frequency range of 150-250 kHz and a constant 25° beam width, these transducers are truly broadband at its best. In addition to improving the performance of Chirp-ready echosounders, anglers using the new wide beam transducers will achieve twice the coverage under the boat compared to our current high frequency Chirp transducers. A unique property of the new high frequency transducers is that the beam width is a constant 25° angle across the entire frequency band. Now, in addition to providing vast bottom coverage and precise fish detection in the upper water column that can sometimes go unseen with our narrow beam transducers, Airmar's new wide beam format also creates crisper and larger return images on the display. We've got you covered. Features: Depth & fast response water-temperature sensor CHIRPs across the following bandwidths: Low Frequency 28 to 60 kHz High Frequency 150 to 250 kHz 25 internal Broadband Ceramics Epoxy housing with stuffing tube and high-performace fairing Boat size: 12M (40’) Hull Type — Fiberglass, Wood, Metal Can retrofit to existing R209 install Exclusive Xducer ID® technology Specifications: Hull Deadrise: 0° to 25° Acoustic Window: Epoxy/urethane Weight: 20.8kg (46lb)

Temperature/Humidity Sensor w/Radiation Shield Features both temperature and humidity sensors inside the radiation shield, which protects the sensors from solar radiation and other sources of radiated and reflected heat. Includes hardware for mounting on a fence post or pole and 25' (7,6M) cable.

Navigation Kit for Sail, Wind Sensor, Transducer, Display & Cables Complex boats need a smart solution. And we have it. VDO Marine OceanLink® display is the only product on the market able to interpret CAN, NMEA 2000® and analog signals without any additional external device.  Safety, performance, entertainment.  VDO Marine Navigation Kit and Navigation Kit Plus is the solution! Our Navigation Kits will become essential crew members which ensure you top performance in the open sea, even in the most extreme situations.  All in one box All you need is in one box including wiring harness and terminators. All products are REACH and RoHS compliant and NMEA 2000® certified. Navigation Kit Plus includes: 1x OceanLink 4.3 TFT Display/Gateway - Black 1x NMEA 2000 Wind Sensor 1x  NMEA 2000 Triducer Airmar Sensor (Speed/Depth/Water Temp) 1x 30m NMEA 2000 backbone (mast) cable 1x 6m NMEA 2000 drop cable 1x NMEA 2000 terminator (female) 1x NMEA 2000 terminator (inline) 2x NMEA 2000 T-splitter WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RayStar 150 GPS Sensor w/Pole Mount RS150 GPS Sensor The RS150 GPS is a high performance, 72-channel, remotely mounted GPS sensor for Raymarine navigation systems. The RS150 offers fast 10Hz position updates and enhanced accuracy. The RS150 is also a GNSS receiver and supports the GLONASS global navigation satellite system. Features: 72-channel GPS receiver Fast 10Hz position updates Satellite differential GPS-compatible. Space-Based Augmentation System (SBAS) enabled with WASS, EGNOS, MSAS and GAGAN support A GNSS receiver with GLONASS compatibility Low power consumption: 30mA (1 LEN) SeaTalkng and NMEA2000 compatible (using a device net adapter cable) Designed for low profile surface mounting or optional pole mounting Specifications: Nominal supply voltage: 12V D.C. Powered by N2K bus Operating voltage range: 8 - 32V DC Power consumption: 30 mA max (NMEA LEN = 1) Operating temperature: -13ºF to 131ºF (-25ºC to +55ºC) Relative humidity: max 93% Waterproof: IPx6/7 Supported connection protocols: SeaTalkng: NMEA 2000 (certified) (via DeviceNet adaptor) Sensitivity: High sensitivity - acquisition down to -163dBm No. of channels: 72 Positioning System: GPS & GLONASS Satellite Differential Type: WAAS (United States); EGNOS (Europe); MSAS (Japan); GAGAN (India) Differential acquisition: Automatic Position accuracy (95%): <15M Position accuracy with SDGPS (95%): <5M Speed accuracy (95%): <0.3kt Time to first fix from cold start: <2 minutes (< 45 seconds typical) Time to first fix from hot start: < 8 seconds -72 hour hold up battery allows for hot start Geodetic Datum: WGS84 Pole Mount for RS150 GPS Antenna Raymarine's Pole Mount specifically for the RS150 GPS Antenna. The RS150 has 72 channels and offers faster 10Hz performance and enhanced accuracy. The RS150 is also a GNSS receiver and supports the GLONASS global navigation satellite system.

GPS160 TriNav Sensor w/iKonvert NMEA 2000 Interface Bundle The GPS160, a high performance positioning sensor using GPS, Galileo and Glonass satellite systems for exceptional positioning accuracies and redundancies. TriNav technology allows all three systems to be simultaneously utilized for navigation. The device can also be field programmed for a variety of modes such as single GNSS operation (eg Galileo only) as well as output configurations such as update rate, NMEA sentence structure etc The GPS160 is available with a NMEA 0183 output (4800, 38400 and 115200 baud programmable) and a USB variant for PC, MAC and Linux. For NMEA 2000 systems, a bundle is available with iKonvert allowing easy and flexible NMEA 2000 installation without the need for cumbersome drop cables. The GPS160 also support an external MOB switch or device. When activated, it creates a “synthesized” AIS SART MOB message on the NMEA output which can be interfaced with a local plotter for MOB identification. The GPS160 supports GPS, Glonass and Galileo positioning. Our TriNav technology is used to combine signals from all three systems to compute the best possible fix accuracy and reliability. Galileo is the global navigation satellite system (GNSS) that has been developed over the past two decades. It joins the GPS and GLONASS systems and offers mariners a 3rd reliable positioning source. It is planned to be fully operational in 2020. Features: 72 channel GPS, Glonass and Galileo GNSS positioning receiver Typically sub 1m accuracy thanks to TriNav technology –combines all satellite data for optimum accuracy Can be configured as dedicated GPS, Glonass or Galileo only device Sophisticated anti-spoofing algorithm for robust positioning performance and interference rejection Available in NMEA 0183, NMEA 2000 (with iKonvert interface)and wireless (with WLN10SM) variants GPS160USB also available with USB connection for PC/MAC User/field selectable 4800, 38400 and 115200 baud operation through simple internal DIP switches Multiple formats of NMEA data output including datum information –user configurable through internal DIP switches Up to 18Hz update rate (user selectable) Ultra low (<20mA) power consumption at 12V DC Input for MOB switch/system – when activated generates synthetic AIS MOB NMEA output to activate MOB position on plotter Professional system (ECDIS) support with datum sentence structure (DTM/GBS/GNS/GRS/GSA/GST) Puck installation or fits 3rd party industry standard 1” x 14 TPI threaded mount

Bronze Thru-Hull Multisensor w/ High-Speed Fairing Block, 600w (8-Pin) 600 Watts 50/200 kHz 40/10 degree Beam Angles Bronze Thru-Hull with Speed and Temperature 30 Foot Cable with 8-Pin Connector WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.