|
FINISH THOMPSON A101470 ADAPTER
Finish Thompson A101470 Motor Adapters
Adapts FTI pumps to Lutz, Standard or Flux motors
FTI to Lutz/Standard - PVC FTI Pump Motor Adapters
|
177.84 |
|
|
FINISH THOMPSON M6 AIR MOTOR
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M6
CE
80-100psi@15-32cfm
400
300-9,000
For use with Finish Thompson Inc. FTI drum pumps. Drum pump motors are available as electric or air pneumatic motors. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.
CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES) without the static protection kit .
Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.
Please allow about two weeks for delivery.
|
467.81 |
|
|
FINISH THOMPSON M6 AIR MOTOR
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M6X
CE
80-100psi@15-32cfm
600
300-9,000
For use with Finish Thompson Inc. FTI drum pumps. This drum pump motor is a air pneumatic motor. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.
CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES without the static protection kit.)
Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.
Air motor performance will depend upon user's compressor and system setup.
Please allow about two weeks for delivery.
|
581.25 |
|
|
FINISH THOMPSON DB10P PUMP END POLY/CARB/VIT/56C
Applications
Water and wastewater
Electronics
Pharmaceuticals
Wet scrubber
Pulp and paper
Finish Thompson DB Series Pump
FTI's DB Series Magnetic Drive Pumps are the product of advanced engineering CFD design software and superior magnetic flux technology. Using powerful neodymium magnetic technology, the DB sealless mag drive pumps are an ideal replacement for mechanical sealed pumps in corrosive duty applications.
Finish Thompson Pumps: Centrifugal - DB10 Model
Motor @ 3450 RPM:
0.33 HP
Motor @ 2900 RPM:
0.34 kW
Max specific gravity:
1.8
Suction Port:
1.50 in
Discharge Port:
1.50 in
Impeller Diameter:
3 in (8.9 cm for 50 Hz model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
67.0 gpm
16.9 m3/hr
Max head
28.0 ft
9.8 m
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 63, 71, 80, 90, w/B14 or B5
Connection type:
NPT, BSP, Flange, Union
Magnet set:
6 pole to 1/2 HP (.37 kW), 8 pole to 1 HP (.75 kW), 10 pole to 2 HP (1.5 kW)
Max pressure:
80 psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
PART NO.
DESCRIPTION
DB10P
Pump End (PP)
DB10PW
Wet End (PP)
DB10V
Pump (PVDF)
DB10VW
Wet End (PVDF)
|
929.70 |
|
|
FINISH THOMPSON A101521 STATIC PROTECTION KIT
Static Protection Kit
Finish Thompson’s Static Protection Kit (SPK) is recommended to help prevent the accumulation of static charge when transferring flammable or combustible liquids. It is to be used in conjunction with stainless steel drum pumps and air or explosion-proof electric motors.
When pumping flammables at high flow rates, a static charge can build up due to the high velocity at which the fluid is moving. Static charge can become a spark capable of igniting flammable liquids. This is rare occurrence, but it is wise to prevent the possibility by using the SPK. Keeping the velocity of the liquid low significantly reduces these hazards. Our metal tube pumps combined with an appropriate motor and static protection kit is an engineered package designed to provide customers with a high level of protection when pumping flammable liquids.
The SPK is a conductive, 4-foot long x 1-inch I.D. cross-linked polyethylene discharge hose with grounding cables to bond the pump, motor, hose and receiving drum. It will also limit the pumps output velocity to 3-feet/second maximum (about 7 gpm through a 1’’ hose), which will reduce static build up.
|
327.60 |
|
|
FINISH THOMPSON DB22-P
Finish Thompson DB22P Pump End Only FTI DB22 Magnetic Drive Centrifugal DB Series Sealless Pumps, 2" Suction, 2" Discharge, FKM O-Ring, Polypropylene, 221 GPM, 90 PSI Max Pressure, 201 Max Feet of Head.
Bushing: Carbon
Connection Type: NPT
Discharge NPT (Inches): 2"
Heads To (Feet): 201
Impeller Size (Inches): 7.25" (7 1/4")
Magnet: 8-pole
Material:Polypropylene (PPG)
Maximum Flow (GPM): 221
Maximum Operating Temperature: 180°F (82°C)
Maximum Pressure (PSI): 90 PSI
Motor Frame Size: 184TC
Pressure Rating BAR: 6.2 bar
Spec. Gravity: up to 1.8
Suction NPT (Inches): 2"
Valve/Seat/O-Ring: FKM
Applications
Chemical transfer
Anodizing
Rinse water & waste water
Pickling chemicals
Pulp and paper
|
3788.96 |
|
|
FINISH THOMPSON DB7P PUMP END POLY/CARB/VIT/56C
Applications
Pulp & Paper
Chemical Processing
Heat Exchanger
Circuit Board Printing
Finish Thompson DB7P Pump End FTI DB7 Magnetic Drive Centrifugal DB Series Sealless Pumps, 1 1/2" Suction, 1 1/2" Discharge, FKM O-Ring, Polypropylene, 69 GPM, 80 PSI Max Pressure, 34 Max Feet of Head
BushingCarbonConnection TypeNPT
Discharge NPT (Inches)1 1/2"
Heads To (Feet)34
Impeller Size (Inches)3.18"
Magnet6-pole
MaterialPolypropylene
Maximum Flow (GPM)69
MaxImum Operating Temperature180°F (82°C)
Maximum Pressure (PSI)80 PSI
Motor Frame Size56C
Pressure Rating BAR5.5 bar
Spec. Gravityup to 1.8
Suction NPT (Inches)1 1/2"
Valve/Seat/O-RingFKM
|
768.60 |
|
|
FINISH THOMPSON 107324-1 ODP MOTOR 1/3HP 115V
S1 FTI EF Series Motor, ODP (Open Drip Proof), Splash-proof, IP24 Motor
|
299.33 |
|
|
FINISH THOMPSON DB11P PUMP POLY CARB/VIT 56C
Applications
Chemical processing
Electronics
Pump cleaning solutions
Printed circuit boards
Pulp and paper
Finish Thompson Pumps: Centrifugal - DB11 Model
Motor @ 3450 RPM:
0.72 HP
Motor @ 2900 RPM:
0.73 kW
Max specific gravity:
1.8
Suction Port:
2.00 in
Discharge Port:
1.50 in
Impeller Diameter:
3.63 in (10.8 cm for 50 Hz model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
78.0 gpm
21.4 m3/hr
Max head
41.0 ft.
14.6 m
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 184TC, 80, 90, 100, 112 w/B14 or B5
Connection type:
NPT, BSP, Flange, Union
Magnet set:
6 pole to 2 HP (1.5 kW), 8 pole to 3 HP (2.2 kW), 10 pole to 5 HP (4 kW)
Max pressure:
90, (50 for Gylon) psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®, Gylon® (gasket)
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
Polypropylene
PVDF
ETFE Lined Ductile Iron
316SS
Max temp.[º F]:
180
220
n/a
n/a
Max temp.[º C]:
82
104
n/a
n/a
PART NO.
DESCRIPTION
DB11P
Pump (PP)
DB11PW
Wet End (PP)
DB11V
Pump (PVDF)
DB11VW
Wet End (PVDF)
ZZZ0002
DB11/15, SP1115 ceramic bushing
ZZZ0011
DB11, SP11 magnet upgrade 8-pole (pump end)
ZZZ0012
DB11, SP11 magnet upgrade 8-pole (wet end)
ZZZ0015
DB11, SP11 magnet upgrade 10-pole (pump end)
ZZZ0016
DB11, SP11 magnet upgrade 10-pole (wet end)
ZZZ0025
DB11/15, SP11/15 union fitting polypropylene
|
1798.20 |
|
|
FINISH THOMPSON DB15P PUMP POLY CARBON VITON 56C
Applications
Bio-filtration
Electroplating
DI water
Electronics
Mining
Finish Thompson Pumps: Centrifugal - DB15 Model
Motor @ 3450 RPM:
1.40 HP
Motor @ 2900 RPM:
0.00 kW
Max specific gravity:
1.8
Suction Port:
2.00 in
Discharge Port:
1.50 in
Impeller Diameter:
4.25 in (50 Hz N/A for this model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
112.0 gpm
n/a
Max head
63.0 ft.
n/a
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 184TC, 80, 90, 100, 112 w/B14 or B5
Connection type:
NPT, BSP, Flange, Union
Magnet set:
6 pole to 2 HP (1.5 kW), 8 pole to 3 HP (2.2 kW), 10 pole to 5 HP (4 kW)
Max pressure:
90, (50 for Gylon) psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®, Gylon® (gasket)
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
Polypropylene
PVDF
ETFE Lined Ductile Iron
316SS
Max temp.[º F]:
180
220
n/a
n/a
Max temp.[º C]:
82
104
n/a
n/a
PART NO.
DESCRIPTION
DB15P
Pump (PP)
DB15PW
Wet End (PP)
DB15V
Pump (PVDF)
DB15VW
Wet End (PVDF)
ZZZ0017
DB15, SP15 magnet upgrade 10-pole (pump end)
ZZZ0018
DB15, SP15 magnet upgrade 10-pole (wet end)
|
1950.30 |
|
|
FINISH THOMPSON DB6HP PUMP END POLY/CARB/VIT/56C
Finish Thompson Centrifugal Pump End Model DB6HP
Motor @ 3450 RPM:
0.21 HP
Motor @ 2900 RPM:
0.16 HP
Max specific gravity:
1.8
Suction Port:
1.00 in
Discharge Port:
1.00 in
Impeller Diameter:
3.12 in (8.9 cm for 50 Hz model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
31.0 gpm
7.9 m3/hr
Max head
31.0 ft.
9.3 m
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 63, 71, 80, 90, w/B14 or B5
Connection type:
NPT or BSPNPT, BSP, Flange, Union
Magnet set:
6 pole to 1/2 HP (.37 kW), 8 pole to 1 HP (.75 kW), 10 pole to 2 HP (1.5 kW)
Max pressure:
80 psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
Polypropylene
PVDF
ETFE Lined Ductile Iron
316SS
Max temp.[º F]:
180
220
n/a
n/a
Max temp.[º C]:
82
104
n/a
n/a
PART NO.
DESCRIPTION
DB6HP
Pump (PP)
DB6HPW
Wet End (PP)
DB6HV
Pump (PVDF)
DB6HVW
Wet End (PVDF)
|
736.88 |
|
|
FINISH THOMPSON DB6P PUMP END POLY/CARB/VIT/56C
Applications
Pulp & Paper
Chemical Processing
Heat Exchanger
Circuit Board Printing
Finish Thompson Centrifugal DB6 Model Pump
Motor @ 3450 RPM:
0.17 HP
Motor @ 2900 RPM:
0.18 HP
Max specific gravity:
1.8
Suction Port:
1.00 in
Discharge Port:
1.00 in
Impeller Diameter:
2.5 in (7.6 cm for 50 Hz model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
31.0 gpm
7.9 m3/hr
Max head
21.0 ft.
7.5 m
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 63, 71, 80, 90, w/B14 or B5
Connection type:
NPT or BSPNPT, BSP, Flange, Union
Magnet set:
6 pole to 1/2 HP (.37 kW), 8 pole to 1 HP (.75 kW), 10 pole to 2 HP (1.5 kW)
Max pressure:
80 psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
Polypropylene
PVDF
ETFE Lined Ductile Iron
316SS
Max temp.[º F]:
180
220
n/a
n/a
Max temp.[º C]:
82
104
n/a
n/a
PART NO.
DESCRIPTION
DB6P
Pump (PP)
DB6PW
Wet End (PP)
DB6V
Pump (PVDF)
DB6VW
Wet End (PVDF)
J101460-1
DB6 - 22 Spare Part
J102789
DB6 - 22 Spare Part
J103617-1
DB6 - 22 Spare Part
J103637
DB6 - 22 Spare Part
J103638
DB6 - 22 Spare Part
J103780
DB6 - 22 Spare Part
|
647.81 |
|
|
FINISH THOMPSON M19 AIR MOTOR
Finish Thompson Drum Barrel Pump BT Series Motor Model: M19
An air motor is a non-electrical device, reducing possibility of explosion from igniting flammables.
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M-19
CE
100psi@80-120cfm
1.5
300-3,000
7,000 cP
|
1808.40 |
|
|
FINISH THOMPSON PFP-27 DRUM PUMP 27" PF POLY
Sealless, High Performance Drum Pump
Unique double suction impeller provides high flow and high head.
Features include:
Polypropylene, PVDF, or 316SS tubes
Interchangeable with motors
Greater flow control with variable orifice discharge (PFM/PFP/PFV only)
Up to 2000 cP with M58P/M59P motors
FDA-compliant option (Click here for more information)
Built-in hose and cord clips (PFM/PFP/PFV only)
Available Lengths:
27, 40, 48, 60, 72 in (69, 102, 122, 152, 183 cm)
Tube Diameter:
2 in (5.1 cm)
Discharge Size:
1 in (2.54 cm)
Discharge Type:
Hose barb w/ variable orifice
Hose Size:
1 in (2.54 cm)
Electric Motor
Air Motor
Maximum Flow:
40 gpm (151 lpm)
22 gpm (83 lpm)
Maximum Head:
80 ft (24 m)
38 ft (11.6 m)
Maximum Specific Gravity:
1.8
1.8
Maximum Viscosity:
2000 cP
330 cP
Tube Material:
Polypropylene
Shaft Material:
Alloy 625
O-ring Material:
FKM
Impeller Material:
PVDF
Maximum Temperature:
160º F (71º C)
Minimum Temperature:
35º F (1.7º C)
|
452.81 |
|
|
FINISH THOMPSON PFP-40 DRUM PUMP 40" PF POLY
Sealless, High Performance Drum Pump
Unique double suction impeller provides high flow and high head.
Features include:
Polypropylene, PVDF, or 316SS tubes
Interchangeable with motors
Greater flow control with variable orifice discharge (PFM/PFP/PFV only)
Up to 2000 cP with M58P/M59P motors
FDA-compliant option
Built-in hose and cord clips (PFM/PFP/PFV only)
Available Lengths:
27, 40, 48, 60, 72 in (69, 102, 122, 152, 183 cm)
Tube Diameter:
2 in (5.1 cm)
Discharge Size:
1 in (2.54 cm)
Discharge Type:
Hose barb w/ variable orifice
Hose Size:
1 in (2.54 cm)
Electric Motor
Air Motor
Maximum Flow:
40 gpm (151 lpm)
22 gpm (83 lpm)
Maximum Head:
80 ft (24 m)
38 ft (11.6 m)
Maximum Specific Gravity:
1.8
1.8
Maximum Viscosity:
2000 cP
330 cP
Tube Material:
Polypropylene
Shaft Material:
Alloy 625
O-ring Material:
FKM
Impeller Material:
PVDF
Maximum Temperature:
160º F (71º C)
Minimum Temperature:
35º F (1.7º C)
|
468.75 |
|