FINISH THOMPSON A101018 BEARING KIT

FINISH THOMPSON A101110 BEARING ASSEMBLY

FINISH THOMPSON A101470 ADAPTER Finish Thompson A101470 Motor Adapters Adapts FTI pumps to Lutz, Standard or Flux motors FTI to Lutz/Standard - PVC FTI Pump Motor Adapters  

FINISH THOMPSON DB10P PUMP END POLY/CARB/VIT/56C   Applications Water and wastewater Electronics Pharmaceuticals Wet scrubber Pulp and paper   Finish Thompson DB Series Pump FTI's DB Series Magnetic Drive Pumps are the product of advanced engineering CFD design software and superior magnetic flux technology. Using powerful neodymium magnetic technology, the DB sealless mag drive pumps are an ideal replacement for mechanical sealed pumps in corrosive duty applications.   Finish Thompson Pumps: Centrifugal - DB10 Model Motor @ 3450 RPM: 0.33 HP Motor @ 2900 RPM: 0.34 kW Max specific gravity: 1.8 Suction Port: 1.50 in Discharge Port: 1.50 in Impeller Diameter: 3 in (8.9 cm for 50 Hz model) Impeller Type: Closed   @ 3450 RPM @ 2900 RPM Max flow 67.0 gpm 16.9 m3/hr Max head 28.0 ft 9.8 m Type: Sealless Configuration: Horizontal Motor frame: 56C, 145TC, 63, 71, 80, 90, w/B14 or B5 Connection type: NPT, BSP, Flange, Union Magnet set: 6 pole to 1/2 HP (.37 kW), 8 pole to 1 HP (.75 kW), 10 pole to 2 HP (1.5 kW) Max pressure: 80 psi Construction materials: Glass-filled Polypropylene, Carbon-filled PVDF O-ring Material: Viton, EPDM, Simriz®, Kalrez® Bushing Material: Carbon, PTFE, Ceramic, silicon carbide PART NO. DESCRIPTION DB10P Pump End (PP) DB10PW Wet End (PP) DB10V Pump (PVDF) DB10VW Wet End (PVDF)

FINISH THOMPSON M100007 BOTTOM BEARING

FINISH THOMPSON M100010 CENTER BEARING

FINISH THOMPSON M101603-2 PFP BEARING GUIDE

FINISH THOMPSON DB22-P Finish Thompson DB22P Pump End Only FTI DB22 Magnetic Drive Centrifugal DB Series Sealless Pumps, 2" Suction, 2" Discharge, FKM O-Ring, Polypropylene, 221 GPM, 90 PSI Max Pressure, 201 Max Feet of Head.   Bushing: Carbon Connection Type: NPT Discharge NPT (Inches): 2" Heads To (Feet): 201 Impeller Size (Inches): 7.25" (7 1/4") Magnet: 8-pole Material:Polypropylene (PPG) Maximum Flow (GPM): 221  Maximum Operating Temperature: 180°F (82°C) Maximum Pressure (PSI): 90 PSI Motor Frame Size: 184TC Pressure Rating BAR: 6.2 bar Spec. Gravity: up to 1.8 Suction NPT (Inches): 2" Valve/Seat/O-Ring: FKM    Applications Chemical transfer Anodizing Rinse water & waste water Pickling chemicals   Pulp and paper    

FINISH THOMPSON DB7P PUMP END POLY/CARB/VIT/56C Applications Pulp & Paper Chemical Processing Heat Exchanger Circuit Board Printing Finish Thompson DB7P Pump End FTI DB7 Magnetic Drive Centrifugal DB Series Sealless Pumps, 1 1/2" Suction, 1 1/2" Discharge, FKM O-Ring, Polypropylene, 69 GPM, 80 PSI Max Pressure, 34 Max Feet of Head   BushingCarbonConnection TypeNPT     Discharge NPT (Inches)1 1/2"     Heads To (Feet)34     Impeller Size (Inches)3.18"     Magnet6-pole     MaterialPolypropylene     Maximum Flow (GPM)69      MaxImum Operating Temperature180°F (82°C)     Maximum Pressure (PSI)80 PSI     Motor Frame Size56C     Pressure Rating BAR5.5 bar     Spec. Gravityup to 1.8     Suction NPT (Inches)1 1/2"   Valve/Seat/O-RingFKM

FINISH THOMPSON M6 AIR MOTOR Model Certification Requirements Output (KW) RPM Maximum Viscosity   M6   CE 80-100psi@15-32cfm 400 300-9,000     For use with Finish Thompson Inc. FTI drum pumps. Drum pump motors are available as electric or air pneumatic motors. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.   CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES) without the static protection kit .   Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.   Please allow about two weeks for delivery.

FINISH THOMPSON M6 AIR MOTOR Model Certification Requirements Output (KW) RPM Maximum Viscosity   M6X   CE 80-100psi@15-32cfm 600 300-9,000     For use with Finish Thompson Inc. FTI drum pumps. This drum pump motor is a air pneumatic motor. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.   CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES without the static protection kit.)   Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.   Air motor performance will depend upon user's compressor and system setup.   Please allow about two weeks for delivery.

FINISH THOMPSON A101521 STATIC PROTECTION KIT Static Protection Kit Finish Thompson’s Static Protection Kit (SPK) is recommended to help prevent the accumulation of static charge when transferring flammable or combustible liquids. It is to be used in conjunction with stainless steel drum pumps and air or explosion-proof electric motors.   When pumping flammables at high flow rates, a static charge can build up due to the high velocity at which the fluid is moving. Static charge can become a spark capable of igniting flammable liquids. This is rare occurrence, but it is wise to prevent the possibility by using the SPK. Keeping the velocity of the liquid low significantly reduces these hazards. Our metal tube pumps combined with an appropriate motor and static protection kit is an engineered package designed to provide customers with a high level of protection when pumping flammable liquids.   The SPK is a conductive, 4-foot long x 1-inch I.D. cross-linked polyethylene discharge hose with grounding cables to bond the pump, motor, hose and receiving drum. It will also limit the pumps output velocity to 3-feet/second maximum (about 7 gpm through a 1’’ hose), which will reduce static build up.

Finish Thompson 106283-2 Magnetic Drive Assembly B6-10 Finish Thompson 106283-2 56C frame, 10-pole, Drive Magnet Assembly with Retaining Ring

FINISH THOMPSON A100002-2 IMPELLER ASSEMBLY Finish Thompson Drum Pump Impeller Assembly, PFP, PFV Barrel pump impeller for all PFP, PFV pumps.

FINISH THOMPSON A100109 STRAINER PVC POLYPRO Finish Thompson Inlet Strainer Prevents intake of objects or particulates. Part Number Construction Applicable Model A100855 Polypropylene PFP A100111 316 Stainless Steel PF, BT A100337 316 Stainless Steel TTS, TBS A100109 PVC/Polyethylene TTC   Not the correct picture