|
FINISH THOMPSON A100109 STRAINER PVC POLYPRO
Finish Thompson Inlet Strainer Prevents intake of objects or particulates.
Part Number
Construction
Applicable Model
A100855
Polypropylene
PFP
A100111
316 Stainless Steel
PF, BT
A100337
316 Stainless Steel
TTS, TBS
A100109
PVC/Polyethylene
TTC
Not the correct picture
|
27.00 |
|
|
FINISH THOMPSON BPC-27 CPVC LAB DRUM PUMP
27" CPVC LAB DRUM PUMP
|
266.18 |
|
|
FINISH THOMPSON A100111 STRAINER 316 SS
Inlet Strainer - Prevents intake of objects or particulates.
Inlet Strainer - Prevents intake of objects or particulates.
Part Number
Construction
Applicable Model
A100855
Polypropylene
PFP
A100111
316 Stainless Steel
PF, BT
A100337
316 Stainless Steel
TTS, TBS
A100109
PVC/Polyethylene
TTC
|
68.64 |
|
|
FINISH THOMPSON A100855 STRAINER POLYPRO
Inlet Strainer - Prevents intake of objects or particulates.
Part Number
Construction
Applicable Model
A100855
Polypropylene
PFP
A100111
316 Stainless Steel
PF, BT
A100337
316 Stainless Steel
TTS, TBS
A100109
PVC/Polyethylene
TTC
|
44.28 |
|
|
FINISH THOMPSON A101470 ADAPTER
Finish Thompson A101470 Motor Adapters
Adapts FTI pumps to Lutz, Standard or Flux motors
FTI to Lutz/Standard - PVC FTI Pump Motor Adapters
|
177.84 |
|
|
FINISH THOMPSON DB10P PUMP END POLY/CARB/VIT/56C
Applications
Water and wastewater
Electronics
Pharmaceuticals
Wet scrubber
Pulp and paper
Finish Thompson DB Series Pump
FTI's DB Series Magnetic Drive Pumps are the product of advanced engineering CFD design software and superior magnetic flux technology. Using powerful neodymium magnetic technology, the DB sealless mag drive pumps are an ideal replacement for mechanical sealed pumps in corrosive duty applications.
Finish Thompson Pumps: Centrifugal - DB10 Model
Motor @ 3450 RPM:
0.33 HP
Motor @ 2900 RPM:
0.34 kW
Max specific gravity:
1.8
Suction Port:
1.50 in
Discharge Port:
1.50 in
Impeller Diameter:
3 in (8.9 cm for 50 Hz model)
Impeller Type:
Closed
@ 3450 RPM
@ 2900 RPM
Max flow
67.0 gpm
16.9 m3/hr
Max head
28.0 ft
9.8 m
Type:
Sealless
Configuration:
Horizontal
Motor frame:
56C, 145TC, 63, 71, 80, 90, w/B14 or B5
Connection type:
NPT, BSP, Flange, Union
Magnet set:
6 pole to 1/2 HP (.37 kW), 8 pole to 1 HP (.75 kW), 10 pole to 2 HP (1.5 kW)
Max pressure:
80 psi
Construction materials:
Glass-filled Polypropylene, Carbon-filled PVDF
O-ring Material:
Viton, EPDM, Simriz®, Kalrez®
Bushing Material:
Carbon, PTFE, Ceramic, silicon carbide
PART NO.
DESCRIPTION
DB10P
Pump End (PP)
DB10PW
Wet End (PP)
DB10V
Pump (PVDF)
DB10VW
Wet End (PVDF)
|
929.70 |
|
|
FINISH THOMPSON DB22-P
Finish Thompson DB22P Pump End Only FTI DB22 Magnetic Drive Centrifugal DB Series Sealless Pumps, 2" Suction, 2" Discharge, FKM O-Ring, Polypropylene, 221 GPM, 90 PSI Max Pressure, 201 Max Feet of Head.
Bushing: Carbon
Connection Type: NPT
Discharge NPT (Inches): 2"
Heads To (Feet): 201
Impeller Size (Inches): 7.25" (7 1/4")
Magnet: 8-pole
Material:Polypropylene (PPG)
Maximum Flow (GPM): 221
Maximum Operating Temperature: 180°F (82°C)
Maximum Pressure (PSI): 90 PSI
Motor Frame Size: 184TC
Pressure Rating BAR: 6.2 bar
Spec. Gravity: up to 1.8
Suction NPT (Inches): 2"
Valve/Seat/O-Ring: FKM
Applications
Chemical transfer
Anodizing
Rinse water & waste water
Pickling chemicals
Pulp and paper
|
3788.96 |
|
|
FINISH THOMPSON DB7P PUMP END POLY/CARB/VIT/56C
Applications
Pulp & Paper
Chemical Processing
Heat Exchanger
Circuit Board Printing
Finish Thompson DB7P Pump End FTI DB7 Magnetic Drive Centrifugal DB Series Sealless Pumps, 1 1/2" Suction, 1 1/2" Discharge, FKM O-Ring, Polypropylene, 69 GPM, 80 PSI Max Pressure, 34 Max Feet of Head
BushingCarbonConnection TypeNPT
Discharge NPT (Inches)1 1/2"
Heads To (Feet)34
Impeller Size (Inches)3.18"
Magnet6-pole
MaterialPolypropylene
Maximum Flow (GPM)69
MaxImum Operating Temperature180°F (82°C)
Maximum Pressure (PSI)80 PSI
Motor Frame Size56C
Pressure Rating BAR5.5 bar
Spec. Gravityup to 1.8
Suction NPT (Inches)1 1/2"
Valve/Seat/O-RingFKM
|
768.60 |
|
|
FINISH THOMPSON DB7V-T PUMP END, PVDF/TEFLON 56C
Pulp & Paper
Chemical Processing
Heat Exchanger
Circuit Board Printing
Magnetic Drive Pump, 3/4 HP,
Voltage 208-230/460,
Full Load Amps 2.4-2.3/1.15, 1-1/2 In.
FNPT Inlet, 1-1/2 In.
MNPT Outlet,
Motor Type Induction, Motor Enclosure TEFC,
69 GPM of Water @ 3 Ft. of Head,
69 GPM of Water @ 6 Ft. of Head,
69 GPM of Water @ 9 Ft. of Head,
64 GPM of Water @ 15 Ft. of Head,
58 GPM of Water @ 18 Ft. of Head,
50 GPM of Water @ 24 Ft. of Head,
Length 17-19/64 In.,
Width 7-1/2 In.
|
1107.90 |
|
|
FINISH THOMPSON M6 AIR MOTOR
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M6
CE
80-100psi@15-32cfm
400
300-9,000
For use with Finish Thompson Inc. FTI drum pumps. Drum pump motors are available as electric or air pneumatic motors. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.
CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES) without the static protection kit .
Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.
Please allow about two weeks for delivery.
|
467.81 |
|
|
FINISH THOMPSON M6 AIR MOTOR
Model
Certification
Requirements
Output
(KW)
RPM
Maximum
Viscosity
M6X
CE
80-100psi@15-32cfm
600
300-9,000
For use with Finish Thompson Inc. FTI drum pumps. This drum pump motor is a air pneumatic motor. Most motors and drum pump tubes are interchangeable. Simply disconnect one from the other.
CAUTION: When pumping flammables, use only air or explosion-proof electric motors on stainless steel (DO NOT PLASTIC TUBES without the static protection kit.)
Non-electrical air operation means the possibility of explosion from igniting flammable gases is reduced.
Air motor performance will depend upon user's compressor and system setup.
Please allow about two weeks for delivery.
|
581.25 |
|
|
Finish Thompson 106283-2 Magnetic Drive Assembly B6-10
Finish Thompson 106283-2 56C frame, 10-pole, Drive Magnet Assembly with Retaining Ring
|
425.36 |
|
|
FINISH THOMPSON 107324-1 ODP MOTOR 1/3HP 115V
S1 FTI EF Series Motor, ODP (Open Drip Proof), Splash-proof, IP24 Motor
|
299.33 |
|
|
FINISH THOMPSON A100002-2 IMPELLER ASSEMBLY
Finish Thompson Drum Pump Impeller Assembly, PFP, PFV
Barrel pump impeller for all PFP, PFV pumps.
|
82.16 |
|
|
FINISH THOMPSON A101521 STATIC PROTECTION KIT
Static Protection Kit
Finish Thompson’s Static Protection Kit (SPK) is recommended to help prevent the accumulation of static charge when transferring flammable or combustible liquids. It is to be used in conjunction with stainless steel drum pumps and air or explosion-proof electric motors.
When pumping flammables at high flow rates, a static charge can build up due to the high velocity at which the fluid is moving. Static charge can become a spark capable of igniting flammable liquids. This is rare occurrence, but it is wise to prevent the possibility by using the SPK. Keeping the velocity of the liquid low significantly reduces these hazards. Our metal tube pumps combined with an appropriate motor and static protection kit is an engineered package designed to provide customers with a high level of protection when pumping flammable liquids.
The SPK is a conductive, 4-foot long x 1-inch I.D. cross-linked polyethylene discharge hose with grounding cables to bond the pump, motor, hose and receiving drum. It will also limit the pumps output velocity to 3-feet/second maximum (about 7 gpm through a 1’’ hose), which will reduce static build up.
|
327.60 |
|