|
SR-2 Jib Roller
The Forespar® SR-2 Jib Roller with fit shrouds from 3/16” thru 3/8” wire diameter.
Use the proper size pair of insert liners according to the table below:
3/8” wire – use no insert
5/16” wire – use #1 inserts
9/32” wire – use #2 inserts
¼” wire – use #3 inserts
7/32” wire – use #4 inserts
3/16” wire – use #5 inserts
The Jib Rollers may be placed just above or below the spreader tips; however, installation will be easier if located below the spreaders. In this instance, you can pre-assemble the parts while on deck and reduce the possibility of losing parts while hanging in a boatswain’s chair. Have a 3 inch piece of masking tape within handy reach (stick it to the shroud).
Select the proper inserts, place them into the two halves of a hub and fit them around the shroud. Use the tape to loosely hold these parts together. Note that the hubs have two clearance screw holes at one end. Match these with the smaller holes at the other end of the other half. It is important that the mating faces of the inserts are parallel with the faces of the hub halves. Install the four screws supplied, tightening only to the extent that you can still slide the hub assembly up the wire shroud. Now remove the tape.
Next, install the rollers. Note that one half of each roller has clearance holes for the two screws. Mate these halves that don’t have clearance holes. Run these screws tight. Now slide the Jib Roller to the desired position on the shroud and finish tightening the four hub screws until the hub interfaces are fully closed.
|
50.44 |
|
|
Venture Bulkhead Combidial Compass
The Venture SR-2 is designed primarily for sailboats 16' (4.88M) to 36' (10.68M) in length.
Features:
3 3/4″ (95 mm) CombiDial
4 5/8″ (118 mm) to 4 13/16″ (122 mm) mounting hole
Vertical Mounting Angle Through 40 Degrees.
Blue LED Night Lighting (12 – 24 Volts)
INC-45 (Inclinometer) Included
Protective Front and Back Covers Included
Exclusive 5-Year Ritchie Warranty
Wheelmark Certified
Approx. Shipping Weight: 2 lb. (907g)
Notes:
12/24v lighting is standard
|
269.93 |
|
|
GP1080-06 SystemPod Pre-Cut f/Raymarine es95/es97/es98 & 2 Instruments (3.6" Hole) for 9.5" Wide Guard
GP1080 Series for 9.5" Guard, SystemPods for Sail are for mounting multiple pieces of electronics in one NavPod. This is a good way to reduce the height of a system. In addition to mounting a radar or chartplotter, you can have room for an autopilot, instrument, stereo controller, or VHF mic.
A SystemPod is best mounted on a Single Bend AngleGuards .
SystemPods for Power are for mounting on a SK135 Stachion Kit can be used to mount a SystemPod on a flat surface, such as the flybridge. Stachion Kits can also be used with a SystemPod for overhead mounting applications.
The Hi-Gloss Material
NavPods are manufactured with a custom co-extruded acrylic capped ABS material. We use the absolute best UV resistant material that provides a very high gloss white finish that matches gel-coated fiberglass. The Gen3 enhancements now include a thicker gauge material that improves strength and provides for better structural rigidity.
The Waterproof Seal
All NavPods are manufactured with a double gasket system providing an excellent watertight seal between the front and back of the NavPod for protection of your Marine Electronics. NavPods are made to withstand the harshest of wet offshore boating conditions. Gen3 enhancements include a thicker external silicone gasket with improved flush fit. The internal EPDM gasket is now 50% thicker and is not subject to "compression set" like many rubber compounds. This is important when you need to open the NavPod in the future to service your electronics.
The Nickel Chrome Plated Screws
We use all stainless steel mounting hardware that is supplied with each NavPod. Large round head tamperproof screws have deeper sockets for the NavPod wrench for better holding ability when tightening than the previous screws. For Gen3 we provide nickel chrome-plated stainless steel tamperproof screws for security combined with a little bling!
The Manufacturing Process
Heavy-gauge thermoforming is considered an art since many processes come into play. It all starts with the design and development of the tooling. We are fortunate to have experienced in-house design engineers who utilize CAD programs like Solidworks, Catia and AutoCad. Surfcam is used to interface with our CNC machining centers to produce quality tools with precision tolerances.
Our Commitment to Quality
We are committed to producing the best possible waterproof housing for Marine Electronics. Now with two decades of experience under our belt, we are confident you will have years of trouble free service and a long lasting high gloss finish. We will stand behind our commitment by now offering a 10-year warranty on all new Gen3 NavPods.
|
462.53 |
|
|
JCU-2 Joystick Controller
The joystick is the primary control for the M400 & M400XR and the M300 series (M300C, M332, M364, M364C, and M364C LR. It is used to wake the system or put it in standby, operate the pan and tilt movement, zoom the camera, control cameras modes and features, and configure system settings by means of OSD menus.
Includes:
Includes:
JCU-2 keypad
Keypad mat
Mounting gasket
4 x mounting screws, rubber washers, mounting clamps
Cable gland nut
RJ45-to-RJ45 Ethernet cable, 7.6 m (25 ft)
Documentation pack
|
1530.96 |
|
|
Perko Vented Flip Top Cap f/Fills with 1-1/2" Hose
Black Polymer
Easily Mounts Directly on Gunnel with Removing Fill Body
Includes Metallic Inserts for Gas, Diesel or Water Fills
Integral Tank Vent with Flame Arrestor
No Deck Plate Key or Ground Wire Required
Flip Top Cap
Technical Information
Requires 5-1/4" Diameter
Mounting Surface Screw Size: #8
|
27.64 |
|
|
Perko Vented Flip Top Cap f/Fills with 1-1/2" Hose
White Polymer
Easily Mounts Directly on Gunnel with Removing Fill Body
Includes Metallic Inserts for Gas, Diesel or Water Fills
Integral Tank Vent with Flame Arrestor
No Deck Plate Key or Ground Wire Required
Flip Top Cap
Technical Information
Requires 5-1/4" Diameter
Mounting Surface Screw Size: #8
|
27.64 |
|
|
Bronze Clam Shell Style Hull Strainer f/Up To 1-1/2" Thru Hull
Features:
C84400 bronze body and door.
Cast filter slots.
Pressure relief holes in door casting.
Specifications:
Flow Type: STD
Mounting Ring Incl.: No
Max T-Hull: 1-1/2"
Perf Dia.: Cast Slots
|
41.33 |
|
|
Bronze Clam Shell Style Hull Strainer w/Mount Ring f/Up To 1-1/2" Thru Hull
Features:
Mount ring design allows easy access to Thru Hulls.
C84400 bronze body and door.
Cast filter slots.
Pressure relief holes in door casting.
Specifications:
Flow Type: STD
Mount Ring Incl: YES
Max T-Hull: 1-1/2"
Perf Dia: Cast Slots
|
82.00 |
|
|
3" Stationary Keel Roller Assembly f/3" Tongue
Product Description
Stationary keel roller bracket assembly for a 3" wide tongue
Bracket
1/8" thick Galvanized
5/8" shaft
1/2" hole slots
3" hole centers
Replacement part #32151G
Roller
Black natural rubber
3" Diameter
4-7/8" wide
5/8" shaft
Replacement part #29522
|
23.70 |
|
|
Ultra Safety Systems US Ultimate SR 12V Bilge Switch
ULTRA PUMPSWITCH SR
Automatic Bilge pump operation (1 1/4" differential) with isolated high water alarm switch (at 3"), built-in.
12V at 15Amp.
Alarm circuit is Normally Open or Normally Closed contacts (current limited to 100 mA max).
Lifetime warranty.
|
214.50 |
|
|
Ultra Safety Systems Ultimate SR 24/32 Volt Bilge Switch
ULTRA PUMPSWITCH SR
Automatic Bilge pump operation (1 1/4" differential) with isolated high water alarm switch (at 3"), built-in.
24/32V at 10 Amps U.L.(30 Amps relay).
Alarm circuit is Normally Open or Normally Closed contacts (current limited to 100 mA max).
Lifetime warranty.
|
224.25 |
|
|
Headhunter SR-20 Mechanical Seal
Please allow a two week lead time.
|
56.43 |
|
|
4' Roller Bunk
Roller bunks make loading and unloading small craft at very short or even dry rams easy. Great for ramps where it is not practical to float the boat onto the trailer. Pre-assembled and pre-drilled for easy installation. Maybe be installed using mounting brackets if lift and/or angle is needed, or may be bolted directly to trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards.
Features:
Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channel
Supports up to 1500lbs of well distributed weight
Mounting hardware not included
Sold in pairs
WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
139.50 |
|
|
5' Roller Bunk
Roller bunks make loading and unloading small craft at very short or even dry ramps easy. Great for ramps where it is not practical to float the boat onto the trailer. Pre-assembled and pre-drilled for easy installation. May be installed using mounting brackets if lift and/or angle is needed, or may be bolted directly to trailer frame for a flat bottom boat, or even mounted on top of existing bunk boards.
Features:
Durable 2" polypropylene rollers on 1/2" shafts mounted in a heavy gauge pre-galvanized channel
Supports up to 1500lbs of well distributed weight
Mounting hardware not included
Sold in pairs
WARNING: This product can expose you to chemicals including ARSENIC ,CADMIUM which are known to the State of California to cause cancer or other reproductive harm, and BERYLLIUM,COBALT METAL POWDER,NICKEL (METALLIC) which are known to the State of California to cause cancer, and Chromium (hexavalent compounds),LEAD which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.
|
156.16 |
|
|
ML-2 LED Combination Deck/Steaming Light
This top selling light has been completely retooled to provide better access for bulb replacement. At the same time, the deck light/bulb assembly has been greatly improved with a prismatic reflector for enhanced deck illumination.
Features:
Steaming Light meets Coast Guard requirements for yachts up to 65' LOA
Separate Switching
10 Watt Boy Light Bulb is easily replaceable (WN-211).8 amps
Deck Light features identical to ML-1
Provided with 6” of triple-lead wire
Weighs 7 oz – measure 5 ¾” vertically
Molded body
Available in black finish only
Mast Light Chafe Guard will also work with Aqua Signal model 254047-7 combo light
Replacement bottom ring for NL-1 & 2. Top bulb ML-2 Bottom Bulb ML-1 & 2. Top Clear Lens, ML-2 only.
|
177.47 |
|