JCU3 Compact Joystick for M100/200 - Raymarine RayNet Network FLIR’s JCU-3 Joystick Controller works with select Thermal Camera Systems to allow full access to the camera’s pan, tilt, zoom and menu settings.  The JCU-3 features 9 buttons plus a rotary controller and joystick trackpad in a compact housing the fits just about anywhere.  The JCU-3 can be mounted either horizontally or vertically using either of the 2 supplied key faces. The JCU-3 is rugged and waterproof for mounting in the pilothouse or on-deck.  It can be surface or flush mounted to your helm, console or bulkhead.  Multiple JCU-3 controllers can be installed to allow control of a single camera from several different locations onboard. The JCU-3’s keypad and rotary knob are backlit for easy viewing at night.  The JCU-3 can bepowered over Ethernet from the vessel’s onboard network, or connected directly to a 12V DC power source and interfaced to the camera with an Ethernet connection.    The JCU-3 is compatible with FLIR M100, M200 (M132, M232) M300, (M300, M332, M354, M364c, M364C LR.

Camera Plate 2 for FLIR m100/200 Thermal Imaging Cameras The modularDual Power Tower has been designed to allow your open array. radar, satdome and camera to be mounted together in one single space saving modular installation. Specifically for Camera plate 2 (FLIR M100/200 Thermal Imaging Cameras) 

RayNet to RJ45 Male Cable - 1m RayNet network cables are for connecting the Digital Sounder Module (DSM) sonar, SR100 Sirius Weather Receiver and additional compatible Raymarine Multifunction Displays. The RayNet connector is used for connecting Raymarine network switches and SeaTalkhs devices to the multifunction display via RayNet cables. Also required for connecting a crossover coupler if only one device is being connected to the display's Network connector. Features: 1m (3.28ft.) RayNet to SeaTalkhs (RJ45) cable The Raynet (F) to RJ45 Ethernet (M) adapter can be used to connect new a, c, e or gS-Series MFDs to the SR6 or 8-Port Seatalk High Speed network switch. When used in conjunction with a crossover coupler, this adapter can also convert the Ethernet connection on a RJ45 radar scanner cable, DSM or thermal camera for direct-connection to an HS5 network switch, or MFD RayNet port.

RayNet (female) to RJ45 Male Cable - 3m RayNet network cables are for connecting the Digital Sounder Module (DSM) sonar, SR100 Sirius Weather Receiver and additional compatible Raymarine Multifunction Displays. The RayNet connector is used for connecting Raymarine network switches and SeaTalkhs devices to the multifunction display via RayNet cables. Also required for connecting a crossover coupler if only one device is being connected to the display's Network connector. Features: 3m (9.84 ft.) RayNet to SeaTalkhs (RJ45) cable

RayNet to RJ45 Male Cable - 10M Part #: A80159 RayNet network cables are for connecting the Digital Sounder Module (DSM) sonar, SR100 Sirius Weather Receiver and additional compatible Raymarine Multifunction Displays. The RayNet connector is used for connecting Raymarine network switches and SeaTalkhs devices to the multifunction display via RayNet cables. Also required for connecting a crossover coupler if only one device is being connected to the display's Network connector. Features: 10M (32.81') RayNet to SeaTalkhs (RJ45) cable

RayNet(M) to RayNet(M) Cable - 100mm The RayNet (M) to RayNet (M) Cable Joiner adapter lets you connect two standard RayNet networking cables together in instances where you need to extend the length of a cable run. Data: Ethernet Length: 100mm

RayNet Cable Pullers - 5 Pack Raymarine's Cable Pullers securely attach to the twist-lock plug on RayNet networking cables and provide a convenient, center-mounted attachment point for your pull string. The cable puller protects the connector's internal pins from damage, acts as a fairing to make pulls through tight spaces easier, and prevents crush/bend damage to the cable/connector joint. The cable pullers are reusable, and come in packages of 5 pullers.

Current Transducer w/Cable f/DCM100 - 200 Amp The Maretron LEMHTA200-S is a current transducer for the Maretron DCM100. Features 200 amps Includes cable WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

MNC-1200 Dual-Band Network Router The Wave WiFi MNC-1200 is a Dual-Band 2.4 and 5Ghz wireless network controller with dual internal access points, gigabit ports, Multi-Source failover functionality, and a host of other robust features to complete a vessels networking needs.  The MNC-1200 provides full usage exposure while providing the ability to control by source/by login code/or by user with features to manage accessibility, cap data, limit bandwidth, and blacklist macs and/or URL's from one easy to access browser based page on any chosen device. In the Box: MNC-1200 Router Two (2) 2.4 Ghz antennas  Two (2) 5 Ghz antennas One (1) 12 VDC power Cable One (1) Ethernet cable (Category 5)  Quick start guide & manual *Sold as an Individual  This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Lenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30256-001 Auto Glide Control Box f/ Dual Actuator 1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

RNS-5 5 Port RayNet Gigabit Switch The RNS-5 network Gigabit switch is designed for expanding Raymarine integrated chartplotter systems using RayNet high-speed Ethernet cabling. Use the RNS-5 to integrate Axiom displays with radars, sonar modules, IP cameras, and Teledyne FLIR thermal cameras. The RNS-5 also supports networking with Raymarine YachtSense digital control systems and the YachtSense Link marine mobile router. Two RNS-5 switches can be daisy-chained together for larger systems. The RNS-5 is simple to install and requires no complicated setup. Features: 5 RayNet Ethernet gigabit ports for fast and reliable connectivity Rugged IPX6 and IPX7 construction Reliable, waterproof RayNet connector Ethernet cable ports Designed for simple bulkhead mounting LED power and network port status indicators Unmanaged- simply plug and play with Raymarine devices No complicated setup or configuration

RNS-8 Network Switch - 8 Port Raynet Network Switch The RNS-8 network switch is a premium network switch for integrated Raymarine chartplotter systems. Use the RNS-8 to integrate Axiom displays with radars, sonar modules, and FLIR thermal cameras. The RNS-8 features 4 dedicated Power-Over-Ethernet (POE) ports for integrating and powering POE-compatible devices like CAM300 marine IP cameras and RMK-10 remote keypads. The RNS-8 also supports networking with Raymarine YachtSense digital control systems and the YachtSense Link marine mobile router. Multiple RNS-8 switches can be daisy-chained together for larger systems. The RNS-8 is simple to install and requires no complicated setup. Features: 8 RayNet Ethernet gigabit ports for fast and reliable connectivity 4 dedicated Power-Over-Ethernet (POE) ports for powering cameras and remotes Rugged IPX6/IPX7 construction Reliable, waterproof RayNet connector Ethernet cable ports Designed for simple bulkhead mounting LED power and network port status indicators Unmanaged- simply plug and play with Raymarine devices. Remote diagnostics and performance monitoring via web browser For extended networks, up to 8 RNS-8 switches can be daisy-chained together

RayNet to RJ45 - 100' RayNet network cables are for connecting the Digital Sounder Module (DSM) sonar, SR100 Sirius Weather Receiver and additional compatible Raymarine Multifunction Displays. The RayNet connector is used for connecting network switches and SeaTalkhs devices to the multifunction display via RayNet cables. Also required for connecting a crossover coupler if only one device is being connected to the display's Network connector. Features: RayNet to RJ45 100'

Raymarine AIS4000 Class A Transceiver Designed for commercial vessels, luxury yachts, and SOLAS high-seas shipping, the AIS4000 Automatic Identification System (AIS) transceiver delivers robust Class A AIS network capability and is engineered to withstand the harsh weather, shock, and vibration of any vessel class. The AIS4000 boasts a high definition color display for quick access to integrated charts, alarms, and tracking. Additional support for wired and wireless networking with shipboard systems make AIS4000 a premier SOLAS and Inland Waterway-certified Class A transceiver.     RUGGED AND VERSATILE Designed for harsh conditions, AIS4000 is right at home on any vessel class. Certified to the highest industry standards for waterproofness, shock, and vibration Compact enclosure with NMEA2000 and NMEA0183 connectivity Junction box included for expanded shipboard sensor and ECDIS connectivity Flexible overhead, bulkhead, desktop, and surface mount options   BOLD, BRIGHT, AND HIGHLY CAPABLE The full-featured AIS4000 brings a new level of functionality to Class A transceivers. Large 5” 800 × 480 color display Integrated Wi-Fi NMEA 2000 Easy-to-use, intuitive interface   ADVANCED CLASS A AIS CAPABILITIES AIS4000 is a full-function Automatic Identification System transceiver certified for SOLAS and Inland Waterway applications. Fourth generation AIS technology for expanded speed, range, and processing performance Full color target display with optional C-MAP ENC mapping Integrated Man Overboard/PLB alerting and tracking system CPA/TCPA data and alarms Specials    Closeouts   Remanufactured    Rebates

RVM1600 Fishfinder Module with RealVision Max The next generation of DownVision, SideVision, 3D, and conventional CHIRP sonar, RealVision MAX, delivers vivid sonar imagery and fish targets like never before. RealVision MAX starts with all-new high-performance RealVision CHIRP transducers, upgraded with larger elements and increased power output for extended-range performance. Next, RealVision MAX signal processing and faster ping rates improve visual fidelity and target identification. With RealVision MAX, the structure is more recognizable, and the most elusive fish are easily identifiable with high-contrast RealVision MAX sonar color palettes. Features: RayNet network compatible with all Axiom displays running LightHouse 4.3 or higher Employs the same RealVision MAX sonar technology built into the new Axiom 2 Pro RVM chartplotters RealVision MAX sonar processing, combined with faster ping rates, delivers superior fish finding in CHIRP, Side, Down, and RealVision channels. RealVision MAX high contrast color palettes provide better visibility of fish and structure. The more powerful 600-watt traditional CHIRP frequency of RealVision MAX transducers provides a deeper sonar range, reducing the need for additional transducers. RealVision 3D provides accurate target location to help pinpoint that elusive wreck or set up the perfect drift. Support for 1kW Airmar CHIRP transducers enables fishing in waters up to 3,000ft (914 meters). Multi-Channel Fishfinder: CHIRP DownVision® delivers a photo-like fish finder view of the world beneath your boat. See bottom structures and fish targets with amazing detail. CHIRP SideVision® sonar expands your underwater horizon with full port and starboard coverage of fish, bait, and underwater structure. See further and see more fish than traditional side scanning sonars. RealVision MAX 3D fish finder lets anglers see below, behind, and to the sides of the boat. Get a new perspective of the underwater world that simplifies locating and staying on structure RealVision MAX Transducers: RealVision MAX transom mount and through hull transducer provide DownVision™, SideVision™, 600-Watt High CHIRP, and 3D sonar capability to the RVM1600.  RealVision MAX transducers feature a built-in attitude and heading reference system (AHRS) for stabilizing 3D sonar imagery and automatically compensating for vessel motion.  A fast-response built-in water temperature sensor provides quick and accurate sea temperature readings. What's In The Box? RVM1600 3D CHIRP sonar module Power cable 1.5 m (4.9 ft) RayNet (female) to RayNet (female) network cable 2 m (6.6 ft) Documentation Mounting screws M4.5 x 20 (x 4)