Baystar Hydraulic Steering System for single-outboard powered boats rated up to 150 HP, including runabouts and inflatables, and outboard engines with ABYC standard engine tilt tubes. For single station, single engine use only. BayStar is not intended for high speed, high performance type boats, such as bass boats. Low friction hydraulic steering system, 5 turns lock-to-lock. Balanced cylinder with compact design that fits most splashwells and provides full engine movement. Compact helm with small footprint, requires only 3" dash hole (standard or tilt).Packaged complete with helm, cylinder, fittings, tubing, oil, fill kit and detailed instructions. Standard 3/4" tapered steering shaft. Meets ABYC standards and NMMA certification requirements. Baystar Steering System is not for use on pontoon boats.

Hoses have an integral bulkhead fitting for tidy routing of hoses through a splashwell bulkhead, helping to eliminate excess loose hose, kinking or chafing. Can be used with all SeaStar systems, except BayStar, Capilano and 3-line inboard. 2 Hoses per kit.

Adhesive Lined Heat Shrink Tubing Kit - 8-Pack, 3", 20 to 2/0 AWG, Black Kit Includes: 8-Black heat shrink tube sections Features: Cross Linked polyolefin tubing is much stronger than PVC tubing and will not burn like PVC Heat activated adhesive lining provides impervious seal to salt water, oil, acids, and sunlight as well as providing strain relief Highest shrink ratio - shrinks to 1/3 original size Shrinks at 257° F/125° C Operating temperature range of -40° C to 110° C UL 224 Color: Black WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Designed for single, non-power-assisted outboard configurations up to 350 hp, especially those capable of speeds over 65 mph, with options like jack plates and performance props. Features No Feedback steering lock valves, low friction hydraulic steering system with ORB fittings on helm and cylinder, 4.0 turns lock to lock. Meets NMMA and ABYC requirements. Refer to application guide below to determine compatibility. Order HO57XX hoses, sold separately.

Jabsco 18753-0608 Tubing Kit

47-Piece Adhesive Lined Heat Shrink Tubing Kit Wire management kit including 47 pieces of adhesive lined heat shrink tubing. Includes: Black (10) 3/16" x 6" (10) 1/4" x 6" (10) 3/8" x 6" (5) 1/2" x 6" (3) 3/4" x 3" (3) 1" x 3" Red (3) 3/4" x 3" (3) 1" x 3" WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

V10-2041 4 Gauge Amp Wiring Kit - 20' (6.1 M) A marine amplifier has to stand up to the rigors of life on the water, and so does the wiring kit you use with it.  The T-Spec V10-2041 Amp Kit is ideal for most single marine amps with a power rating of up to 1000 watts and will give you reliable power for seasons to come. Features: Complete marine amplifier wiring kit Includes power wire, ground wire, turn-on wire, circuit breaker, ring terminals, wire ties, and more Marine-compliant cable In the Box: 4 AWG pearl White OFC copper wire - 20' 4 AWG matte Grey OFC copper wire - 20' 18 AWG Blue wire - 20' (1) 100 amp circuit breaker (1) 1/0 AWG ring terminal with White boot (1) 1/0 AWG ring terminal with Silver boot (10) 6" Wire ties *Sold as an Individual WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Major Rebuild Kit for Sherwood M-5 This kit contains the following items GY 211P-2 1 SQ-HD-PLUG 1/8-B MS DATA SHEET 1 DATA SHEET SH 10077K 1 IMPELLER KIT SH 10093 1 KEY-WOODRUFF SH 10285 1 CAM SH 10286 1 VELLUMOID 505 FIBRE GASKET SH 10514C 2 LIP SEAL SH 10822 1 SCREW 10-24 X 3/8 SH 11519 1 GRAPHITE BUSHING SH 12863 1 RETAINING RING SH 344 6 SCREW 10-24 X 3/8 SS MACHN WB 298485 1 MTG GASKET FOR 202M-15   Kits are put together at time of order

Minor Repair Kit for Sherwood M-5 This kit contains the following items   SH 10077K 1 IMPELLER KIT SH 10514C 1 LIP SEAL   Kits are put together at time of order

Major Rebuild Kit for Sherwood M-71 This kit contains the following items   MS DATA SHEET 1 DATA SHEET ON 3008400 1 MTG GSKT FOR P17XX PUMPS SH 10514C 1 LIP SEAL SH 10515C 1 SCREW & WASHER SH 10615K 1 IMPELLER KIT SH 10944 1 CAM BRASS LARGE CHRYSLER SH 12211 2 BALL BEARING SH 12710 3 LOCKWASHER SH 12857 3 SCREW SH 12859 1 SEAL/SEAT ASSEMBLY SH 25150 1 WEAR PLATE SH 4258 2 SNAP RING (SMALL) SH 4259 2 SNAP RING (LARGE) SH 4264 1 WASHER SH 4432 1 KEY SH 5133 1 SPACER     Kits are put together at time of order

Minor Repair Kit for Sherwood M-71 This kit contains the following items   SH 10615K 1 IMPELLER KIT SH 12859 1 SEAL/SEAT ASSEMBLY   Kits are put together at time of order

Speedometer Pitot Tube Kit  Universal design works with most Speedo's. 522100(-1) are Pitot Tube only. Speedometer Pitot Tube Installation Kit 522105-1 includes pitot, pitot tube shield, clamps, and mounting screws. WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

External Cell Antenna Kit - 20' The Wave WiFi high gain external cellular antenna is designed to be used with SIM activated cellular systems. The external cellular antenna features 1” - 14 threads for use on standard marine mounts (not included.) Compatible with the MBR550 and/or the MNC1250. Features: 20' of low loss 240 cable 1" - 14 Thread mount base In the Box: Wave WiFi cellular antenna 20' Cable Quick start guide and manual *Sold as an Individual

Manual Discharge Cable Kit - 20' Designed for manual activation of the MA and GA Series of fire suppression systems.  The manual discharge cable kit is a backup for those who prefer the extra measure of control or for inspected vessels who are required by U.S. Coast Guard regulation.  Compatible With: MA, MU, MA2, GA, GA1 and GA2 Series of fire suppression systems Features:  Easily routed with engine cables and electrical wiring  Various lengths for vessel specific installation  In the Box: Cable - 20' Mounting plate Pull handle Safety pin *Sold as an Individual 

XPS Hose Kit - 20' This Panther hose kit is needed for the Panther XPS System. Features: The low-pressure hose is 12 in. longer to allow for uninterrupted travel when connected to the cylinder actuator 20 ft. – 1/4 in. Hi-Pressure Hose  21 ft. – 5/16 in. Return Hose Includes: Contains two hoses high pressure and low pressure—with fittings