OMC 400 type cable (Pre 1979). Stainless steel core. Stainless steel and brass fittings. Exceeds engine manufacturers specifications. 6" minimum bend radius.

2018 Jeep Wrangler JL A-Pillar Mount for 2 D-Series, D-SS, SR-M or Ignite Lights The 2018 Jeep Wrangler JL can go anywhere that you can take it, shouldn’t its auxiliary lighting options do the same? The all new Wrangler JL A-Pillar mount by RIGID gives that extra lighting needed for those dark times.  With the ability to attach several different RIGID lighting options from the D-Series, D-SS, SR-M, or Ignite families, the RIGID Jeep Wrangler A-Pillar mount takes auxiliary lighting to a new level. These mounts are made from laser cut stainless steel and have been powder coated allowing for a clean sleek look. Own The Night with the RIGID mounts for your Jeep Wrangler JL.  Lights sold separately.  In the Box: All Necessary Hardware ∗ Sold as a Pair

Xtreme® premium control cables provide smooth, easy action with minimum lost motion. Superior feel at the controls, especially in multi-station vessels. Patented splined core with ridges that allow a close fit with the cable's inner liner, but with minimum contact so the core glides back and forth smoothly. .34" super tough HDPE jacket for ultimate protection from the elements.

Replacement rotary steering cable with simple snap-in connection. Direct replacement for SSC61 and SSC72 cables. Stainless steel core.

Drop-in replacement cable for Mercury/Mercruiser engines using 600A type cable. Splined core allows easy movement and minimum lost motion. Designed for complex and/or long cable runs, or to simply create a superior feel. Stainless steel fittings and cable wire. 4" min. bend radius. Packed one per box.

Drop-in replacement cable for OMC outboard and I/O engines using 479 type cable. Splined core allows easy movement and minimum lost motion. Designed for complex and/or long cable runs, or to simply create a superior feel. Stainless steel fittings and cable wire. 4" min. bend radius. Packed one per box.

Mercury/Mercruiser 600A type cable. Complete drop-in replacement cable for Mercury/Mercruiser engines. Stainless steel & brass fittings. Stainless cable wire. WHILE QUANTITIES LAST.

Designed specifically to be used with late model Mercury 4000 series controls. Engineered to significantly reduce or eliminate cable "Wig-Wag", this design results in a significantly improved feel with less shifting effort. Improves the feel of the Mercury 4000 Series Controls. Nickel plated brass swivel tube. WHILE QUANTITIES LAST.

OMC 479 type cable (1979 & later). Complete drop-in replacement cable for OMC O/B and I/O's. Stainless steel and brass fittings. 6" minimum bend radius. WHILE QUANTITIES LAST.

Replacement cable for Mariner low horsepower engines when used with Mercury controls. Uses existing connection components. Also used for converting old Mercury control boxes to Japanese motors. Stainless & brass fitting, stainless cable wire.

3" travel, 10-32 thread stainless steel ends. Stainless 16 strand Lubri-Core wire for smooth operation. 6" minimum bend radius. Stainless steel rods, hubs, and end fittings. Covered core wires with moisture protective seals help protect against corrosion and lengthen cable life. UV resistant polyethylene outer jacket resists abrasion and withstands effects of salt water, chemicals, gasoline, and oil.

Drop-in replacement cable for engines with controls that accept cable with 10-32 threaded ends. Mercury Sport Jet requires connection kit #CA27319P for engine end. Stainless steel conduit fittings. 3" nominal travel. 4" minimum bend radius. Packed one per box.

RJ45-M Ethernet Adapter Cable RJ45-Yellow Round Ethernet adapter cable for Simrad NSO evo2 and Zeus2 displays.

Fuel Flow Sensor with 10' cable & T-connector Fuel Flow Sensor Gasoline ONLY. 1 required per engine. Up to 3 engines supported. Outputs: Fuel Flow Tank Fuel Used Trip Fuel Used Seasonal Fuel Used Cable Length: 10' Fuel Line Diameter: 3/8" (9.5mm) Inside Diameter Flow Rate Measured: Optimized for 0.6-45 Gal/hr but can measure outside these values Added Back Pressure to the fuel system: 0.5 PSI at 20 Gal/hr; 1 PSI at 40 Gal/hr Installation Location: Above the max level of the fuel tank, in-line after the fuel filter and any Y's or T's in the line Package: The Fuel Flow Sensor, N2K T and 2 (two) 1" hose clamps Fuel Type: Gasoline only. The Fuel Flow Sensor does not operate diesel engine fuel systems Hole required to route through a bulkhead: 22mm (7/8") Multiple Fule Flow sensors possible: Yes

Medium Cable Gland - #14-#10 Cable SMS Enclosure Gland PG16 Accepts Cable #14-10 (3 Conductor) WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.