Jabsco 1983-0010 Ss Shaft  

Jabsco 17366-1000 SS Shaft  Detroit Diesel 8927572, Caterpillar 3N5692

Jabsco 2567-0000 Ss Shaft For 653, 671, 853  

Jabsco Phenolic Pump W/Ss Shaft &Amp; Viton   FEATURES Pump Body: Phenolic Type Plastic Port Size: 5/8" ID Hose Slip On Flow: 5.8 GPM at 10 feet of Head, 1750 RPM Pressure: 13 PSI Max Impeller: Neoprene, Nitrile or Viton Shaft Seal: Lip Type Shaft: Stainless Steel or Hastelloy Bearing: Filled Teflon - Replaceable     APPLICATIONS / CHARACTERISTICS INDUSTRIAL: Designed for: Carboy and drum transfer, hazardous chemical transfer and recirculation, recirculation of descaling compounds through refrigeration and condenser coils, printed circuit etching, general laboratory transfer, photographic fixes and developers, barium transfer, transfer of ammonia on blueprint machines, silver recovery, demineralized and distilled water. The only metallic parts in the 3010 series are the shaft and the drive pin   Jabsco Phenolic Pump W/SS Shaft & Viton Impeller

Jabsco 6987-0000 Ss Shaft For 671Ti 871 1271  

Jabsco 824-2001 Ss Shaft For 6400 &Amp; 7420  

Tuthill 1LEV-C-A-7 Pump 3.2Gpm Tang Shaft Cast Iron Rotary Gear Pump Pump End Only L Series Pump Cast Iron Construction NO motor Has Internal Relief Valve. Relief valve is set at 55 PSI (can be adjusted in field) Clockwise rotation only (from shaft end view) Tang Shaft Inlet Port is 1/2 inch NPT Discharge Port is 1/2 inch NPT Positive Displacement, Internal Rotary Gear Design Open Flow at 1800 RPM : 3.0 GPM at 1800 RPM Standard Discharge Pressure: up to 500 PSI Inlet Pressure: up to 280 PSI Maximum Differential Pressure: 300 PSI Temperature: up to 375 F Typical Viscosity Range: 40 to 1000 SSU

Tuthill 2LEV-C-A-7 Pump 6.2Gpm Short Shaft Type: Internal Gear Maximum Flow Rate: 6.2 gpm Max Pressure: 300 psi Inlet/Outlet Port Sizes: 1/2 in NPT Pump Body Material: Cast Iron Wetted Materials: Steel, Carbon, Bronze, P/M Steel, Carbon O-Ring Material: Viton, Neoprene, EPR Seal: Viton Mechanical Seal

Jabsco 1983-0020 Shaft  

Jabsco 10487-0010 Pump Shaft SHAFT FOR 2" PUMP 18370 Replacement shaft for 11470 series pumps. Steel construction.   Image is representation only of this shaft.

Jabsco 18590-0010 Pump 12V Macerator 1" ID Hose Barb Pump Body: Plastic Self-Priming Flexible Impeller with Stainless Steel Wearplate. Port Size: Inlet – 3" Slip-on Hose Outlet: 1" ID Hose Barb Flow: 13 GPM at 5 feet of head Impeller: Nitrile Shaft Seal: Lip Type Shaft: Stainless Steel Motor: 12 Vdc Permanent Magnet Type, Fully Enclosed, with Stainless Steel Shaft. Macerator: Cast Bronze Cutter reduces particle size to 1/8" maximum.   The Jabsco 18590-series DC macerator pump unit is the ideal solution for emptying holding tanks on recreational vehicles and avoiding dump stations. The macerator section grinds waste down to a particle size of 1/8" maximum so it can easily be pumped through a 1" ID discharge hose. The pump section is self-priming, permitting the unit to be mounted above the tank in a convenient location. Empties most recirculating toilets in less than 2 minutes; empties a typical 30 gallon holding tank in less than 3 minutes.  

Jabsco 18690-0010 Heavy Duty Macerator Pump 115V 3" Ports Pump Body: Plastic, Self-Priming Flexible Impeller with Stainless Steel Wearplates. Port Size: Inlet – 3" Slip on Hose Outlet – 1" ID Hose Barb Flow: 14 GPM Macerator: Cast Bronze Cutter Plate reduces particle size to 1/8" maximum. Impeller: Nitrile Shaft Seal: Lip Type Motor: 115 Vac, AC Induction Type Single Phase, 60 Hz Thermal Overload Protection.    APPLICATIONS  The Jabsco 18690-0010 AC macerator pump unit is the ideal answer to waste handling problems for marine, recreational vehicle and domestic uses. The macerator section grinds waste down to a particle size of 1/8" maximum so it can be pumped easily through a 1" hose discharge line. The pump is self-priming, permitting the unit to be mounted above or below the tank in a convenient location. For optimal efficiency, locate pump as close to waste source as practical. Empties a 30 gallon holding tank in only 3 minutes. The 18690-0010 waste pump will macerate and pump all waste and tissue normally found in marine waste systems.  

Jabsco 18940-0010 Engine Cooling Pump 1 1/4" Ports Pump Body: Bronze Port Size: 1 1/4" ID Hose Impeller: Neoprene Shaft Seal: Carbon-Ceramic Face Type Shaft: Stainless Steel Pulley: 6 1/2" diameter "A" belt     This Jabsco alternator mounted engine driven water pump has been used on a wide range of engines including Chrysler, Lehman, and Powerhouse Marine. Engineered for marine applications and a long service life, the body is cast bronze and features a stainless steel shaft. Impeller access is available by removing the front portion of the pump body. Hose barbs are cast into the pump body so that tail pieces are not required for installation. Pump is driven by a 6 1/2" pulley that is compatible with type A belts.   Key Features Flange mounted engine driven flexible impeller water pump Self-priming at slow RPMs Includes 6 1/2" pulley compatible with type A belts Corrosion resistant bronze pump body  Stainless steel shaft for superior corrosion resistance   Compatible engines   Chrysler: replaces Sherwood model G5 LM 318 LM 340 LM 360 LM 383 LM 400 LM 440 Lehman 302, 351 cu. in. Powerhouse Marine 302, 351 cu. in.  

Major Service Kit for Jabsco 4590-0001 This kit contains the following items     JA 3791-0000 1 PACKING JA 4518-0000 1 PACKING GLAND JA 4595-0000 1 COVER JA 4598-0001-P 1 IMPELLER KIT NEO JA 706-0010 1 GASKET JA 91003-0010 6 SCREW (1 PER BAG) JA 91004-0010 1 SCREW (1 PER BAG) JA 91402-0010 1 KEY JA 91501-0010 2 GREASE FITTING JA 9215-0010 1 KEY FOR 5320-0011 JS 01-42679 1 CAM 1/1 MS DATA SHEET 1 DATA SHEET   This kit is put together at time of order.

Major Service Kit for Jabsco 4590-0003 This kit contains the following items   JA 3791-0000 1 PACKING JA 4518-0000 1 PACKING GLAND JA 4595-0000 1 COVER JA 4598-0003-P 1 IMPELLER KIT NITRILE JA 706-0010 1 GASKET JA 91003-0010 6 SCREW (1 PER BAG) JA 91004-0010 1 SCREW (1 PER BAG) JA 91402-0010 1 KEY JA 91501-0010 2 GREASE FITTING JA 9215-0010 1 KEY FOR 5320-0011 JS 01-42679 1 CAM 1/1 MS DATA SHEET 1 DATA SHEET     This kit is put together at time of order.