Auto Glide Boat Leveling System for Single Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box, the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Single Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30255-001 Auto Glide Control Box f/ Single Actuator 1 30248-001 Auto Glide Control Box Harness f/ Single Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki E Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Lenco Auto Glide Boat Leveling System f/Dual Actuator Tab Systems w/Existing NMEA 2000 A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30256-001 Auto Glide Control Box f/ Dual Actuator 1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Auto Glide Boat Leveling System A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box, the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Single Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30255-001 Auto Glide Control Box f/ Single Actuator 1 30248-001 Auto Glide Control Box Harness f/ Single Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' 1 30262-001D CAN bus #2 GPS/NMEA 2000 Network Adapter Cable - 2.5' 1 30266-001 NMEA 2000 GPS Antenna Only 3 30267-001D Tee Connector Only 2 30268-001D Terminating Resistor - Female 1 30268-002D Terminating Resistor - Male 1 30281-001D Power Cable - NMEA 2000 Network 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki E Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

A Real Automatic Boat Control / Trim Tab Control System that actually works - completely & automatically! The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again! The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system. Imagine that your boat's running angle is measured 25 times per second and this data is used by the new Auto Glide control box to: Automatically put your boat in the most efficient running angle. Reduce the amount of bow rise of your boat during hole shot mode. Eliminate bow porpoising (bow bounce). Keep your boat level at all times. These actions will result in a smoother ride and the best possible fuel efficiency. The Auto Glide has 3 automatic operational modes, 4 automatic settings, and 2 manual operational modes. Although you will most likely keep your Auto Glide in automatic mode, you may immediately convert to manual mode simply by pressing one of the 4 up/down buttons on the key pad. The main components are the Auto Glide Key Pad, the Auto Glide Control Box , the Control Box Main Harness, and various cables. These cables connect the Auto Glide system to your engine(s), to your GPS unit, your network, and/or a Stand Alone GPS Antenna/Receiver. Boat must have Lenco Dual Trim Tab System with Lenco Electric Actuators. This is a MUST in all applications. For Aftermarket Systems: The Lenco Glide System will work on ALL boats with ALL engines. GPS data is used to provide data to control box. Optional connection to NMEA 2000 Network is included.For OEM System: For OEM System: Connection to analog systems is available. Connection to CANbus-based engines is available. See list below. Boat must have NMEA 2000 GPS network or NMEA 2000 antenna receiver. NMEA 0183 will work, but will have slower signal response. Lenco offers a NMEA 2000 GPS antenna receiver and optional stainless steel mounting bracket. Kit Contains 1 30254-001D Auto Glide Key Pad Control 1 30256-001 Auto Glide Control Box f/ Dual Actuator 1 30247-001 Auto Glide Control Box Harness f/ Dual Actuator 1 30259-001D CAN bus #1 NMEA2000 Cable - 2.5' 1 30262-001D CAN bus #2 GPS/NMEA 2000 Network Adapter Cable - 2.5' 1 30266-001 NMEA 2000 GPS Antenna Only 3 30267-001D Tee Connector Only 2 30268-001D Terminating Resistor - Female 1 30268-002D Terminating Resistor - Male 1 30281-001D Power Cable - NMEA 2000 Network 2.5' Available for these CANbus-based engines: NMEA2000 Engines Yamaha (Command Link Plus requires NMEA 2000 / Yamaha Gateway P/N:6Y98A2D00000) Evinrude Honda Suzuki Volvo Penta (Non-EVC Engines) (With a Volvo NMEA2000 Gateway - Volvo P/N 3889757) J1939 Engines Volvo Penta (EVC Engines) Yanmar Caterpillar Cummins Detroit Diesel John Deere Steyr SmartCraft Engines Mercury - Verado Mercury - Optimax with SmartCraft ECU Mercruiser with SmartCraft ECU Cummins/Mercruiser w/ SmartCraft ECU WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

  Lenco Automatic Trim Tab Control System   A real automatic boat control/trim tab control system that actually works - completely and automatically!  The Auto Glide system controls your trim tabs from the time you leave your dock until you come home again.  The Auto Glide uses engine data and GPS data (depending on your installation method) to drive your boat to the most efficient running angle by adjusting your Lenco trim tabs as needed. This optimum running angle is determined during the set-up process after the installation of your Auto Glide system.              Closeouts     Rebates    Remanufactured    Specials

102 Series Standard Actuator - 12V - 4-1/4" Stroke w/Hardware The 102 Actuator is used with Trolling Tab systems sold prior to 2000 and OEM applications. 4.25 stroke. Overall length (tip to tip) is 14 inches. Instant response electric actuators are made of high impact glass fiber filled, ultraviolet-resistant nylon material with 316 super buff stainless steel tubing. Specifications: Newly implemented Anti Extrusion Ring (AXR) seal stabilization system. Stronger top cap and mounting clevis design Improved pressure-tight torx screws Integrated wiper seal at actuator base Molded-in brass thrust bearing design Thicker and stronger motor housing wall Improved O-Ring design for more consistent seal Over-molded cable providing a stronger tighter seal Upper mounting bracket with gland seal Features: Lenco's ballscrew design is more reliable and twice as powerful compared to typical hydraulics Lenco's tough, high-torque actuator motor easily pushes 500 pounds. Lenco Actuator connections use waterproof "Plug & Play" Deutsch connectors eliminating the possibility of water intrusion. 12 Volt 5/16" mounting hardware 6 foot cable WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

102 Series Standard Actuator - 24V - 4-1/4" Stroke w/Hardware The 102 Actuator is used with Trolling Tab systems sold prior to 2000 and OEM applications. 4.25 stroke. Overall length (tip to tip) is 14 inches. Instant response electric actuators are made of high impact glass fiber filled, ultraviolet-resistant nylon material with 316 super buff stainless steel tubing. Specifications: Newly implemented Anti Extrusion Ring (AXR) seal stabilization system. Stronger top cap and mounting clevis design Improved pressure-tight torx screws Integrated wiper seal at actuator base Molded-in brass thrust bearing design Thicker and stronger motor housing wall Improved O-Ring design for more consistent seal Over-molded cable providing a stronger tighter seal Upper mounting bracket with gland seal Features: Lenco's ballscrew design is more reliable and twice as powerful compared to typical hydraulics Lenco's tough, high-torque actuator motor easily pushes 500 pounds. Lenco Actuator connections use waterproof "Plug & Play" Deutsch connectors eliminating the possibility of water intrusion. 24 Volt 5/16" mounting hardware 6 foot cable WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Lenco to Bennett Conversion Kit - Electric to Hydraulic Economical, easy installation alternative to replacing Lenco actuator or purchasing an entire trim tab system. Uses existing Lenco trim planes. No need to patch or re-drill mounting holes. Kit Includes: Custom adapter plates for actuator and trim plane assembly Bennett Hydraulic Power Unit Two standard actuators Water resistant Rocker Switch Control, hardware and all wiring WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

LED Indicator Integrated Tactile Switch Kit with Pigtail for Single Actuator Systems Complete your Lenco trim tab system with the latest, maintenance-free (ALL-IN-ONE) integrated tactile switch kit design. This NEW switch technology improves accuracy and integrates the control box functionality into the key pad bezel. LED indicator lights let you know exactly where your trim tabs are at all times. A backlit keypad automatically illuminates graphics for night viewing. A photo eye reads ambient light and adjusts the indicator intensity for optimum viewing in all lighting conditions. Features Include Simple, quick, Plug & Play installation Instant response Built-in retractor Low profile design Self-contained key pad with waterproof Plug & Play Deutsch connectors Wiring harness length 30" (76.2 cm) from the back of the switch bezel 36" power pigtail 2 1/16" hole cut-out size, overall key pad size of 2.75" x 2.75" 4.08" clearance required from the back of the key pad's mounting location 2 high-intensity LED Indicator displays show the exact position of your trim tabs at all times Photo Eye for optimum viewing in all light conditions Backlit key pad for optimum viewing at night Self-Check feature Replacement parts are available and are sold separately.  Specifications 3 Year Warranty System Type: Single Actuator Compliance: CE Certified WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Adapter Cable - 2.5' CANbus #2 GPS/NMEA2000 GPS Adapter Use when connection to NMEA 2000 GPS Antenna/Receiver WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Adapter Cable - 2.5' CANbus #2 GPS/NMEA 2000 Network Adapter Cable Assembly Use when connecting to NMEA 2000 Network WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Standard Integrated Tactile Switch Kit with Pigtail for Single Actuator Systems Complete your Lenco single actuator trim tab system with the latest, maintenance-free (ALL-IN-ONE) integrated tactile switch kit design. This NEW switch technology improves accuracy and integrates the control box functionality into the key pad bezel.  Features Include Simple, quick, Plug & Play installation Instant response Built-in retractor Low profile design Self-contained key pad with waterproof Plug & Play Deutsch connectors Wiring harness length 30" (76.2 cm) from the back of the switch bezel 36" power pigtail 2 1/16" hole cut-out size, overall key pad size of 2.75" x 2.75" 4.08" clearance required from the back of the key pad's mounting location ATTENTION: REPLACEMENT KEY PADS & CONTROL BOXES FOR 2016 & PRIOR SWITCHES ARE NOT COMPATIBLE WITH THIS SWITCH KIT. Replacement parts are available and are sold separately.  Specifications 3 Year Warranty System Type: Single Actuator Compliance: CE Certified WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Reactor™ 40 Mechanical/Retrofit/Solenoid Corepack without Display The Most Responsive Autopilot System on the Water Solid-state 9-axis Attitude Heading Reference System (AHRS) Minimizes heading error, course deviation, rudder movement and power consumption while providing a comfortable ride Minimal commissioning and calibration Supports heading hold, wind hold, step turns and tack/jibe modes With a complete package designed for powerboats and sailboats, Garmin brings an advanced marine technology to the boating public that was once only available for commercial boats. The Reactor 40 autopilot series is simply the most responsive autopilot system we have ever offered. Reactor 40 autopilots are very versatile. Both powerboat and sailing features are available in all corepacks, including heading hold, wind hold, tack/jibe, step turns and more; simply pick the autopilot that’s compatible with your existing steering system. If you don’t see a compatible Reactor 40, you’ll find the Reactor 40 mechanical/retrofit/solenoid is compatible with a wide variety of steering systems, whether hydraulic, cable drive, mechanical and solenoid. Just pair GRF™ 10 with your drive system already on board. The Reactor 40 mechanical/retrofit/solenoid autopilot corepack is ideal for sailboats and powerboats with direct or cable-actuated steering systems. This Reactor 40 below-deck autopilot system gives captains that “extra set of hands” they need so you can safely attend to your sails, lines, winches and radios, without worry. With its solid-state 9-axis AHRS, Reactor 40 mounts anywhere, in any orientation and requires minimal commissioning. Solid-state 9-axis AHRS With its advanced solid-state 9-axis AHRS, you can mount Reactor 40 nearly anywhere, in any orientation. In addition, this new system greatly minimizes heading error, course deviation, rudder movement and power consumption while providing a comfortable ride for all on board. Reacts to Conditions This amazing autopilot actually reacts to the sea to hold your course. Even when the boat is pitching and rolling, you can remain confident that the Reactor 40 autopilot will keep you on your desired course. Minimal Commissioning and Calibration All autopilots require commissioning and calibration — all of them. We know you just want to get on the water, so we made this process as fast and easy as possible. That’s the power of simple. Full Integration with Garmin Chartplotters Combined with a compatible Garmin networked chartplotter, you can have full control of Reactor 40 from wherever you are on the boat. In addition to holding its course in virtually all weather and wind conditions, the system can smoothly perform a variety of preprogrammed trolling and search procedures. Plus, with a compatible Garmin networked chartplotter and BlueChart® g2 Vision® charts (sold separately), you gain optional features such as Auto Guidance¹, which automatically steers GPS paths. Stay in Control with Shadow Drive™ Technology On hydraulic installations, the Reactor 40 mechanical/retrofit/solenoid autopilot corepack can add optional patented Shadow Drive technology. This gives you the security of knowing you maintain control, even when the autopilot is engaged. The Shadow Drive system automatically disengages the autopilot if the helm is turned, giving you the freedom to maneuver the boat. The autopilot automatically re-engages when you hold a steady course. Choose from 3 Class Drives Reactor 40 is available with 3 linear drives (sold separately) capable of driving many different steering systems on most midsize to large vessels (depending on the particular installation). All Garmin linear drives include built-in rudder feedback sensing. Class A Drive Unit — up to 28,500 lbs of displacement Class B Compact Drive Unit — up to 48,400 lbs of displacement Class B Drive Unit — up to 79,000 lbs of displacement Add Even More Peace of Mind Add an optional GRF 10 rudder feedback sensor, and you can further enhance the performance of your Reactor 40 autopilot. ¹Auto Guidance is for planning purposes only and does not replace safe navigation operations What's In The Box? Reactor 40 CCU (Course Computer Unit) ECU (Electronic Control Unit) ECU power cable Interconnect cable Buzzer NMEA 2000® drop cables (2 meters) NMEA 2000 T-connectors Male and female terminators Documentation WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Auto Glide Control Box Mounting Bracket - SS Stainless Steel mounting bracket for Auto Glide Control Box WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

LED Indicator Two-Piece Tactile Switch Kit with Pigtail for Single Actuator Systems This LED tactile switch kit has a shortened bezel for consoles which require less depth to mount. Functionality is built into the externally mounted control box and must be mounted separately. LED indicator lights let you know exactly where your trim tabs are at all times. A backlit keypad automatically illuminates graphics for night viewing. A photo eye reads ambient light and adjusts the indicator intensity for optimum viewing in all lighting conditions. Features Include Simple, quick, Plug & Play installation Instant response Built-in retractor Low profile design Self-contained, sealed key pad & solid state control box with waterproof Plug & Play Deutsch connectors 36" power pigtail for control box 2 1/16" hole cut-out size, overall key pad size of 2.75" x 2.75" 2.33" clearance required from the back of the key pad's mounting location 2 high-intensity LED Indicator displays show the exact position of your trim tabs at all times Photo Eye for optimum viewing in all light conditions Backlit key pad for optimum viewing at night Self-Check feature ATTENTION: REPLACEMENT KEY PADS & CONTROL BOXES FOR 2016 & PRIOR SWITCHES ARE NOT COMPATIBLE WITH THIS SWITCH KIT. Replacement parts are available and are sold separately.  Specifications 3 Year Warranty System Type:Single Actuator Compliance:CE Certified WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov. This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.