|
Triggers for Mercury, Mariner and Force outboards.
|
125.57 |
|
|
Fits: 30, 40, 50, 60 HP, 4 Stroke 1999-Up Mercury; 40HP 2000 & Up 4-Stroke Yamaha. 9-tooth drive gear. Uses DV365 replacement drive gear, SR365 repair kit.
|
226.81 |
|
|
Fits: 75, 90HP 4-Stroke Mercury/Mariner 1999 and Up; 80, 100HP 4-Stroke Yamaha 1999 and Up. 13 Tooth
|
493.96 |
|
|
Fits: 40-50 HP 1996-99. 13-tooth drive gear. **Battery stud exits from BOTTOM of starter. Uses DV394 replacement drive gear, SR394 repair kit. **See 5397 also, determine location of the battery stud on starter being replaced before ordering.
|
194.54 |
|
|
Evinrude Outboard Relay - E-TEC
Evinrude outboard relay that will fit Evinrude E-TEC. O/B Tilt /Trim Relay.
Replaces:
2011-2012 - E-TEC 25, 30, 40, 50, 60, 75, 90, 115, 130, 150, 175, 200, 225, 250, 300
2008-2010 - E-TEC 30, 40, 50, 60, 75, 90, 115, 130, 150, 175, 200, 225, 250, 300
2007 - E-TEC 40, 50, 60, 75, 90,115, 150, 175, 200, 225, 250 2006 E-TEC 40, 50, 60, 75, 90, 200, 225, 250
2005 - E-TEC 40, 50, 75, 90, 200, 225, 250
2004 - E-TEC 40, 50, 75, 90
*ARCO Assurance 12-month part and labor warranty protection
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
118.79 |
|
|
Original Equipment Quality Replacement Outboard Starter for Evinrude 40, 50, 75 & 90 HP E-TEC Models
This outboard starter will fit Evinrude 40, 50, 75, and 90 HP E-Tec Models, 9-tooth drive gear.
ARCO advises using a fully charged battery - A weak battery can damage the starter and starter solenoid. And to also clean all connections - A corroded connection creates resistance, lowering the amperage required for an efficient starting circuit.
Features:
Dynamically tested and packaged for out-of-the-box performance
Nickel-coated and/or epoxy-painted to reduce corrosion
Sealed to minimize water intrusion
Designed for long life and optimum performance
Armatures are tested to withstand 50 times operating voltages (12 volts)
Warranty Information:
When properly installed, all ARCO products are warrantied against defects in materials and workmanship for 12 months for leisure use and 90 days for commercial or racing applications.
Add an extra year of warranty to your rotating electric ARCO product (Tilt/Trim Motors, Alternators, Outboard Starters, and Inboard Starters) when you register your product within 30 days of purchase. You can register your product by visiting arcomarine.com/product-registration
Replaces:
BRP-OMC 586768
BRP-OMC 587045
SIERRA 18-6826
This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.
|
138.56 |
|
|
Stylish stainless steel bezel design, black on white graphics. Domed glass sheds water and resists scratching. A comprehensive family of instruments for outboards, stern drives and inboards, including diesels. Lido instruments feature crisp white dials and fire-orange pointer tips. Red through-dial and white perimeter lighting for great night readability. NOTE: Mariner 30 & 40 HP 2-cylinder engines require a module (Merc. part no. 17461A2) when using Lido tachometer.
|
112.99 |
|
|
Yamada K45-AM Air Motor Kit Ndp-40/50
NDP-40/50 AIR MOTOR RESEAL KIT,
(2) 640020 O'Ring,
(2) 685444 Buna V-Packing,
(2) 640029 O'Ring,
(2) 711937 Pilot Valve (Spring 40,50,80),
(1) 771712 Valve Body (Gasket 40,50,80),
(2) 771738 Spool Cap (Gasket 40,50,80),
(2) 771740 Pilot Valve (Seat 40,50,80),
(2) 771742 Gasket 40, 50, 80,
(2) 772689 Nylon Throat Bushing,
(2) 832162 Pilot Valve Assy 40, 50,
(1) 805084 C-Spool Assembly Carbon Filled
|
477.06 |
|
|
Smart Tab Trim Tabs 9 X 8 f/13-15' Boats w/30-40 HP
IMPROVES YOUR BOAT'S OVERALL PERFORMANCE GUARANTEED!!!
If these trim tabs don't provide you with an outstanding performance increase, contact us within 30 days of your purchase.
Why buy a manually adjusting trim tab set when you can get the automatic trim tabs that will self adjust and perform better for less money?
Our breakthrough technology in trim tabs is completely automatic requiring no operator adjustment while underway. Nauticus trim tabs self adjust according to how you load and maneuver your boat.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.
Reduce the minimum planning speed by up to 33%
Faster Acceleration
Increase top speed
Provide a level, more comfortable ride at lower speeds
Improve fuel economy, handling and safety
NO HYDRAULICS - NO ELECTRIC SWITCHES
Nauticus trim tabs are completely automatic requiring no operator adjustment while underway.
The nitrogen Gas Actuator provides LIFT at the stern of the boat by holding the trim plate down during acceleration. The amount of LIFT is determined by the actuator load rating and the trim plate adjustment, which is done at the time of installation.(see installation instruction).
SPEED REGULATED
Nauticus trim tabs start in a downward angel to maximize lift at slow speeds. As the boat accelerates, the water pushes up on the trim plates providing lift to the stern which minimizes bow rise, and allows the boat to plane quickly.
Once the water pressure exceeds the actuator load rating (maximum lift) the trim plates move up to a horizontal position eliminating any drag.
BOAT STABILIZERS
Even when cruising SMART TABS continue to work like shock absorbers. The constant adjustment to sea conditions allow SMART TABS to provide remarkable stability in turns, while crossing waves, while cruising, and while running at maximum speeds. No more sliding, porpoising, or chine walking.
ONE OF A KIND
The unique system is the only one of its kind in the industry. The internal valve system is truly "smart" in its design of controlling you boats performance.
It will reduce the minimum planning speed by 33%
Provide a level, more comfortable ride at lower speeds
Improve economy, handling and safety
As the boat speed increases, the water pressure also increases. Once the water pressure exceeds the Actuator load rating (maximum LIFT period) the trim plates begin to move upward until they are horizontal with the bottom of the boat.
The internal valve system dampens the trim plate movement which eliminates any instant reaction to minor water pressure variances. Nauticus trim tabs provide smooth and undetectable reaction to boat speed creating a level, more comfortable ride at lower speeds.
INSTALLATION IS SIMPLE
With an electric drill, small drill bit, a phillips screwdriver, and two wrenches, just about anyone can install SMART TABS in less than an hour. Professional installers should be able to install SMART TABS in 30 minutes or less.
All mounting hardware, instructions, and templates are included.
SMART TABS require NO THROUGH HULL DRILLING
|
122.12 |
|
|
Wire Harness - High Power f/40" - 50" Light Bar
This 13' wiring harness is designed to connect a single 40"-50" LED light bar to your 12V electrical system. It features battery terminals on one end and a Deutsch connector on the other to connect to the light. It incorporates an inline fuse holder, a 12V relay, and a waterproof switch. This harness is compatible with the following RIGID Industries LED Lights: 50" E-Series, 50" SR-Series.
Features:
14 AWG Wire
Deutsch Connector
Inline Fuse Holder
|
45.37 |
|
|
Drive Pin Set for BOW 50/60/75/80/95
Replacement Stainless Drive pin for the VETUS BOW 50/60/75/80/95 (5x27.5mm) propeller shaft.
|
47.05 |
|
|
Set Spare 6 Blade Prop D 185mm for BOW 50, 60, 75, 80 & 95
Propeller 6 blade, diameter 178mm, shaft 13.7mm, for 50/60/75/80/95 kgf bow thrusters.
|
106.56 |
|
|
Fits: OMC 25, 40, 50 HP; 2-cyl - 1989-Up; 48-50 HP - 1990-Up. Replaces: OMC. 583482, 585056. 9-tooth drive gear. Uses *DV389 replacement drive gear, *DVK89 2-piece drive kit (fits current-model starters), SR389 repair kit. *NOTE: New OMC outboard starters use a 2-piece drive assembly while older OMC outboard starters use a 1-piece drive assembly. When ordering starter drives make certain you choose the correct drive because the new and old style OMC drive assemblies are not interchangeable!
|
202.41 |
|
|
Fits: 40, 50, 60 HP 4 stroke 4 cylinder 0P094500 & Up and 50, 60 HP EFI 4 stroke 4 cylinder, 0P153500 & Up.
|
334.99 |
|
|
Sierra voltage regulators for Mercury/Mariner outboards.
|
120.99 |
|