Micropump GA-T23.J9FS.A Pump Head A Mount The GA Series high-performance pumps provide precise and pulseless flows. Featuring Micropump's suction-shoe design, GA Series pumps self-compensate for wear, ensuring near zero slip and a longer pump life. Pumps are available in a wide range of materials and configurations. Feature: Small Size Smooth, Pulseless Delivery Chemically Resistant Easy to Service Proven Reliability Advanced Pump Technology Wide Range of Options OEM Configurations Enhanced Efficiency Pump Series: GA Series Ports/Fittings: 1/8-27 (F) NPT Side Ports Min Speed (RPM): 500 Max Speed (RPM): 5500 Max Pressure (psi): 300 Min Temperature (°C): -46 Max Temperature (°C): 177 Max Diff. Pressure (psi): 75 Displacement (ml/rev): 0.092 Design: Standard Design Gear Set: 0.125/2/40 (0.092 ml/rev) Gear Material: PEEK (hex drive) Static Seals: PTFE Base Materials: 316SS Drive Mount: MP Housing Bypass: No Driven: Ferrite Driving Magnet: Not Included High System Pressure: No Bushings: None Shafts: 316SS Gear TrimNone Model: GA-T23.J9FS.A

Calpeda CM22/A Motor and Pump Close-coupled Centrifugal Pump with open impeller Single Phase 230v with Thermal Proctector. Capacitor is inside the terminal box

Calpeda BCM22/A Motor and Pump Calpeda's BC-series monobloc centrifugal pumps are complete with open impeller. Available in either cast iron or bronze, single-phase or three-phase.   Close-coupled centrifugal electric pumps with open impeller. Backward (vortex) impeller for type C 16/1E. C: version with cast iron pump body and fitting. B-C: version with bronze pump body and fitting. Bronze pumps are supplied fully painted.   For liquids moderately charged with impure emulsions. For industry and agriculture. For Marine AC Water Pump   Liquid temperature from -10 °C to +90 °C. Ambient temperature up to 40 C. Total suction lift up to 8 m. Maximum permissible working pressure: 6 bar. Maximum size of solids: 4 mm. Continuous duty.

Calpeda NM2/A 07H36S Centrifugal Pump 3Ph 3/4Hp The motor of the Calpeda NM2/A 07H36S centrifugal pump has a power rating of three-quarters horsepower.   Calpeda Model number is NM 2/A-60 Three-phase 230/460 V Insulation class F Protection IP 44   Pump casing: Cast iron Lantern bracket: GJL 200 EN 1561 Impeller: Brass CW510L (lead-free public LAW 111-380) Shaft: Cr steel AISI 430 Cr Ni steel AISI 302 for 1 - 1.5 - 2.5 - 3 HP Mechanical seal: Carbon- Ceramic- NBR   Liquid temperature from 14 F to 194 F Ambient temperature up to 104 F Total suction lift up to 23 ft Maximum permissible working pressure up to 145 psi (232 psi for pumps NMD) Continuous duty   For clean liquids without abrasives, which are, non-aggressive For the pump materials ( solids content up to 0.2%) For water supply For heating, air-conditioning, cooling, and circulation plants For civil and industrial applications   For irrigation  

Calpeda NM25-12B/A Cast Iron Pump NM 25/12B/A 230/400V 0,55kW 2900rpm Close-coupled centrifugal pump with electric motor and extended shaft directly connected to the pump.   NM: single-Impeller.   Connections: threaded ports ISO 228/1 (BS 2779).   NM, NMD: version with pump casing and lanter bracket in cast iron. B-NM, B-NMD: version with pump casing and lanter bracket in bronze (the pumps are supplied fully painted).   For clean liquids without abrasives, which are non-aggressive for the pump materials (solids content up to 0.2%) For water supply For heating, air-conditioning, cooling and circulation plants For civil and industrial applications For fire fighting applications For irrigation

Oberdorfer 300B Series Self Priming Centrifugal Pump FEATURES Pump Body: Bronze Ports: 1" NPT Flow: 22 GPM Max Pressure: 15 PSI Max, 35 feet of head Impeller: Centrifugal Shaft Seal: Mechanical Buna Seal Standard, Viton or Teflon Optional Shaft: Stainless Steel Standard, Monel Optional Motor / Drive: Attaches to NEMA C flange jet pump motors with threaded shaft of stainless steel or monel. We can supply additional motors and assemble if required.     APPLICATIONS / CHARACTERISTICS This close coupled style bronze self-priming centrifugal pump is equipped with high quality ball bearings permanently filled with grease for maintenance free operation.  The main shaft seal is a mechanical face type seal of proven reliability.  Unlike positive displacement pumps centrifugal pumps have larger internal clearances as the pressure is generated by centrifugal force and high liquid velocity.  These pumps can handle impurities in the liquid and the flow in the discharge line may be throttled or shut off without the need for a relief valve. FEATURES Self-Priming to 20 Feet Suction Lift Rugged Bronze Construction Ideal for marine service (air conditioning, bilge, and sea water recirculating). O-Ring Housing seal eliminates gasket problems Auxiliary Connections - for convenient priming and draining Multiple Mechanical Shaft Seal Options -for various applications Pump Heads mount to Standard Footed Nema 56J Jet Pump Motors Shafts : 416 Stainless, Nickel Alloy, or 316 Passivated Stainless Multiple motor options including Explosion Proof For Pedestal Style, see 30PB Optional Lifting Handle DRIVE Centrifugal pumps are designed for single rotation and are non reversible.  Standard rotation is counter clockwise looking at the pump inlet port (clockwise facing pump shaft).  Close coupled centrifugal pumps may be driven by a variety of power sources such as electric motors, hydraulic motors or air motors. Self priming centrifugal pumps must be operated in the horizontal position.  LIQUIDS & TEMPERATURES Capacity - Water 60o F - Gallons Per Minute Maximum lift without foot valve is 10 feet. Bronze pumps are suitable for most common liquids in the pH range from 4-11.  If in doubt consult with factory or check the Oberdorfer™ Chemical Resistance Guide booklet.  The temperature limit for bronze pumps is 212F.  Higher temperatures are possible with fluoroelastomer or Polytetrafluoroethylene (PTFE) seals.  Centrifugal pumps are not well suited for pumping viscous liquids.  Viscosities up to 2000 SSu may be handled resulting in reduced performance and efficiency. Pump seal is mechanical carbon face type mated to ceramic wear face for maximum durability. Other seal components are made of Nitrile with low swell characteristics for compatibility with a wide range of liquids including many chemicals and solvents. SUCTION LIFT Up to 22 gallons per minute water flow and suction lift of 15 feet without a foot or check valve (25 foot suction lift using a foot or check valve and a filled inlet line). A 1/2” pipe plug on the tank top is for initial filling of priming chamber and inlet line--pump priming is automatic thereafter.      300B is Oberdorfers - Self Priming Centrifugal Pump Head Only Bronze    

Oberdorfer 109MB Series Centrifugal Pump FEATURES Pump Body: Bronze Ports: Inlet: 1 1/4" NPT Outlet: 1" NPT Flow: 80 GPM Max Pressure: to 19 PSI, 45 feet of head Impeller: Centrifugal Shaft Seal: Teflon Barrier Seal to Protect Motor Bearings. Carbon Face Mechanical Pump Seals. Buna Std., Viton and Teflon available. Shaft: 416 Stainless Steel is standard, Monel Shaft available for Marine Use Motor / Drive: Pump heads mount to standard footed NEMA 56J jet pump motors. A wide variety of motors are available and we can assemble for you.     APPLICATIONS / CHARACTERISTICS Oberdorfer™ centrifugal pumps have a single rotating metal impeller. Liquid enters at the center and is thrown outward radially by centrifugal force. The impeller is not in contact with other pump parts resulting in quiet, efficient, pumping action. The flow produced is not positive which permits the discharge line to be shut off completely without danger of overloading motors or bursting lines. Consequently a relief valve is not required. The liquid flow varies directly as the pump speed—the higher the speed the greater the flow. Horsepower required varies directly as flow and pressure. Maximum horsepower is required with a wide open discharge line. This is the point of maximum flow. With a throttled discharge, the flow decreases at a greater rate than the pressure increases thereby requiring less horsepower at the higher pressures. This is known as an “unloading” feature of the pump. FEATURES Rugged Bronze Construction A Standard in the Marine Air Conditioning Industry Extremely Quiet Operation O-Ring Housing seal eliminates gasket problems Polytetrafluoroethylene (PTFE) Barrier Seal to protect motor bearings Handles Contaminated Liquids Discharge port orientation flexibility-8 positions Mechanical Seal - Carbon/Ceramic, Nitrile - standard, Fluoroelastomer (S10) optional, Polytetrafluoroethylene (PTFE)(S11) optional Pump Heads mount to standard footed Nema 56J Jet Pump Motors Shafts: 416 Stainless, Nickel Alloy, or 316 Passivated Stainless Multiple motor options available For Industrial Version - see Model 700 series DRIVE This close-coupled pump uses a standard NEMA C-Flange Jet Pump Motor with weld-on base and threaded shaft end to accept the pump impeller. Single phase motors are nonreversible and are wired for the proper pump rotation which is counter-clockwise looking at the inlet end of the pump. (See the dimensional drawing.) Three phase motors must be checked out for proper rotation when the pump is installed.  Interchanging of any 2 wires in a 3-phase system will reverse motor rotation.  LIQUIDS & TEMPERATURES The special pump alloys used provide corrosion resistance to many liquids including water, water solutions, and a wide range of commercial chemicals. Questions as to the chemical compatibility of special liquids should be referred to the factory. The pump uses a mechanical type shaft seal with a Nitrile rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212oF and 75 P.S.I. Fluoroelastomer (S10) seals and Polytetrafluoroethylene (PTFE) (S11) seals are available for severe solvents and difficult chemicals. Viscous liquids with a maximum viscosity of 2000 Saybolt Seconds Universal can be pumped. However, when pumping viscous liquids as compared with water, a reduction in flow and pressure occurs and the required horsepower rate increases.  Liquids heavier than water require additional horsepower in direct proportion to the increase in specific gravity. Liquids contaminated with small solids or abrasives can be handled, but a reduction in mechanical seal life must be expected.  SUCTION LIFT These centrifugal pumps are not self-priming. They must be installed below the liquid level so that the liquid flows to the pump by gravity (flooded suction). However, if a foot valve is used at the beginning of the suction line and all air is bled from the pump by manual priming, the pump will lift on the suction side up to 15 feet. Such a system relies entirely on a non-leaking foot valve for starting capability.   Will Handle Contaminated Liquids. Extremely Quiet. A Standard in the Marine Air Conditioning Industry.     109MB is Oberdorfers - Centrifugal Pump Head Only Bronze 1 1/4" X 1"NPT  

MP Pumps 36089 HHLF 2" x 2" High Head Low Flow Self Priming Centrifugal Pump, Bronze, Pumped, Closed Couple Motor, 1.12, 6.5" Impeller, High Rise Suction     HHLF (High Head Low Flow) "HR" high pressure self-priming centrifugal pumps meet USCG specifications for auxiliary fire control (46 CFR compliant) and is ABS type approved. The high suction centerline and impeller design eliminates premature priming loss while ensuring consistent priming capability. The HHLF pump is capable of achieving up to 25 feet suction lift. The HHLF series is available close coupled to NEMA "C" Face electric motors or as PumPAKs. The engine drive models are capable of close coupling to both gasoline and diesel engines with 1" keyed drive shafts. Pedestal mounted pumps are also available. The volute and impeller are removable and easily replaced.   46 CFR Complaint ABS Type Approved Drive Sleeve 304 stainless steel Adaptor Cast iron Class 30 or silicon bronze CA 875  

Oberdorfer 300B Series Self Priming Centrifugal Pump FEATURES Pump Body: Bronze Ports: 1" NPT Flow: 22 GPM Max Pressure: 15 PSI Max, 35 feet of head Impeller: Centrifugal Shaft Seal: Mechanical Buna Seal Standard, Viton or Teflon Optional Shaft: Stainless Steel Standard, Monel Optional Motor / Drive: Attaches to NEMA C flange jet pump motors with threaded shaft of stainless steel or monel. We can supply additional motors and assemble if required.     APPLICATIONS / CHARACTERISTICS CLOSE COUPLED BRONZE SELF-PRIMING CENTRIFUGAL PUMP Bronze Models with Monel Shaft Sleeve - Ideal for marine service (air conditioning, bilge, and sea water recirculating). Can handle most difficult solvents with proper seal arrangement. Suction lift of 15 feet without a foot or check valve.       300B-F13 is Oberdorfers - Self Priming Centrifugal Pump Bronze 1/3HP 115/220V  

Oberdorfer 300B Series Self Priming Centrifugal Pump FEATURES Pump Body: Bronze Ports: 1" NPT Flow: 22 GPM Max Pressure: 15 PSI Max, 35 feet of head Impeller: Centrifugal Shaft Seal: Mechanical Buna Seal Standard, Viton or Teflon Optional Shaft: Stainless Steel Standard, Monel Optional Motor / Drive: Attaches to NEMA C flange jet pump motors with threaded shaft of stainless steel or monel. We can supply additional motors and assemble if required.     APPLICATIONS / CHARACTERISTICS CLOSE COUPLED BRONZE SELF-PRIMING CENTRIFUGAL PUMP Bronze Models with Monel Shaft Sleeve - Ideal for marine service (air conditioning, bilge, and sea water recirculating). Can handle most difficult solvents with proper seal arrangement. Suction lift of 15 feet without a foot or check valve.     300B-01-F26 is Oberdorfers - Self Priming Centrifugal Pump Bronze 1/3HP 115/230V Monel Shaft  

Oberdorfer 300B Series Self Priming Centrifugal Pump FEATURES Pump Body: Bronze Ports: 1" NPT Flow: 22 GPM Max Pressure: 15 PSI Max, 35 feet of head Impeller: Centrifugal Shaft Seal: Mechanical Buna Seal Standard, Viton or Teflon Optional Shaft: Stainless Steel Standard, Monel Optional Motor / Drive: Attaches to NEMA C flange jet pump motors with threaded shaft of stainless steel or monel. We can supply additional motors and assemble if required.     APPLICATIONS / CHARACTERISTICS CLOSE COUPLED BRONZE SELF-PRIMING CENTRIFUGAL PUMP Bronze Models with Monel Shaft Sleeve - Ideal for marine service (air conditioning, bilge, and sea water recirculating). Can handle most difficult solvents with proper seal arrangement. Suction lift of 15 feet without a foot or check valve.       300B-01-J26 is Oberdorfers - Self Priming Centrifugal Pump Bronze 1/2HP 115/230V Monel Shaft  

Oberdorfer 300B Series Self Priming Centrifugal Pump FEATURES Pump Body: Bronze Ports: 1" NPT Flow: 22 GPM Max Pressure: 15 PSI Max, 35 feet of head Impeller: Centrifugal Shaft Seal: Mechanical Buna Seal Standard, Viton or Teflon Optional Shaft: Stainless Steel Standard, Monel Optional Motor / Drive: Attaches to NEMA C flange jet pump motors with threaded shaft of stainless steel or monel. We can supply additional motors and assemble if required.     APPLICATIONS / CHARACTERISTICS CLOSE COUPLED BRONZE SELF-PRIMING CENTRIFUGAL PUMP Bronze Models with Monel Shaft Sleeve - Ideal for marine service (air conditioning, bilge, and sea water recirculating). Can handle most difficult solvents with proper seal arrangement. Suction lift of 15 feet without a foot or check valve.     300B-F21 is Oberdorfers - Self Priming Centrifugal Pump Bronze 1/3HP 1PH Explosion Proof  

MP Pump 21381 FLOMAX 15 Self Priming Centrifugal Pump MP Pumps Flomax 15 Self Priming Centrifugal Pumps for Water & Fertilizer w/ Pedestal Mount FLOMAX self priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line.   A FLOMAX Pump is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 56C and 145TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. Options include double grease-lubricated seals, stainless steel impeller and seals for all types of abrasive and / or corrosive services.   The FLOMAX® series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Washdown Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Model: Flomax 15 Part #: MP21381 Size: 3 in. NPT Flow-Rate: 320 GPM Head Feet: 145   Features Material of Construction: Cast Iron Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift   Applications Agricultural Industrial Marine OEM  

Oberdorfer 104M Series Centrifugal Pump FEATURES Pump Body: Bronze Ports: Inlet: 3/4" NPT Outlet: 1/2" NPT Flow: 24 GPM Max Pressure: to 23 PSI, 53 feet of head Impeller: Centrifugal Shaft Seal: Teflon Barrier Seal to Protect Motor Bearings. Carbon Face Mechanical Pump Seals. Buna Std., Viton and Teflon available. Shaft: 416 Stainless Steel is standard, Monel Shaft available for Marine Use Motor / Drive: Pump heads mount to standard footed NEMA 56J jet pump motors. A wide variety of motors are available and we can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED CENTRIFUGAL PUMP This close-coupled pump uses a standard NEMA C-Flange Jet Pump Motor with weld-on base and threaded shaft end to accept the pump impeller. The pump uses a mechanical type shaft seal with a Buna rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212 F. Viton® seals and Teflon seals (Chemlon) are available for severe solvents, difficult chemicals, and elevated temperatures.   Will Handle Contaminated Liquids. Extremely Quiet. A Standard in the Marine Air Conditioning Industry.   Oberdorfer Centrifugal Pump 1/3HP ODP 115 Volt Only    

Oberdorfer 104M Series Centrifugal Pump FEATURES Pump Body: Bronze Ports: Inlet: 3/4" NPT Outlet: 1/2" NPT Flow: 24 GPM Max Pressure: to 23 PSI, 53 feet of head Impeller: Centrifugal Shaft Seal: Teflon Barrier Seal to Protect Motor Bearings. Carbon Face Mechanical Pump Seals. Buna Std., Viton and Teflon available. Shaft: 416 Stainless Steel is standard, Monel Shaft available for Marine Use Motor / Drive: Pump heads mount to standard footed NEMA 56J jet pump motors. A wide variety of motors are available and we can assemble for you.     APPLICATIONS / CHARACTERISTICS BRONZE CLOSE COUPLED CENTRIFUGAL PUMP This close-coupled pump uses a standard NEMA C-Flange Jet Pump Motor with weld-on base and threaded shaft end to accept the pump impeller. The pump uses a mechanical type shaft seal with a Buna rubber element. It is suitable for water, oils, and some mild solvents and it is limited to 212 F. Viton® seals and Teflon seals (Chemlon) are available for severe solvents, difficult chemicals, and elevated temperatures. Will Handle Contaminated Liquids. Extremely Quiet. A Standard in the Marine Air Conditioning Industry.   Oberdorfer Centrifugal Pump 1/2HP ODP 115/230V Monel Shaft