|
Groco C-60 12V Deck Wash Pump, 12Volt
Groco- Deck Wash Vane Pump System 6.5GPM 20-40psi 12VDC
More Info: C60
|
724.50 |
|
|
Groco C-60 24V Deck Wash Pump, 24Volt
Groco- Deck Wash Vane Pump System 6.5GPM 20-40psi 24VDC
More Info: C60
|
732.96 |
|
|
Calpeda CAOPH220 Pump Housing for MXH 204-404
|
224.00 |
|
|
Calpeda 16006010000 Mechanical Seal X6H62V6
Calpeda Pump Shaft Seal Mechanical Seal
Mechanical Seal Type: TYPE3 R X6H62V6D12 Standard
Shaft Diameter: 12 mm (D12)
Calpeda Position Number: 36:00
|
98.55 |
|
|
Tuthill 00LE-C-7 Pump 1Gpm 1 1/2" Ports
Pump Body: Cast Iron
Shaft Seal: Mechanical Seal Viton
Port Size:Inlet Port is 1/2 inch NPT, Discharge Port is 1/2 inch NPT.
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 1.0 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
593.75 |
|
|
Tuthill 000LEV-C-7 Pump 0.5Gpm 3/8 Ports
Pump Body: Cast Iron
Relief Valve: Relief valve is factory set to 55 PSI with adjustment between 55-120 PSI
Shaft Seal: Mechanical Seal Viton
Port Size: Inlet Port is 3/8 inch NPT, Discharge Port is 3/8 inch NPT
Product Specs :
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 0.5 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
702.50 |
|
|
Tuthill 1LEV-C-7 Pump 3.2 Gpm
Cast Iron Rotary Gear Pump
Pump End Only
Tuthill L Series Pump
Cast Iron Construction
Has Internal Relief Valve
Relief valve is set at 55 PSI (can be adjusted in field).
Clockwise rotation only (from shaft end view)
Inlet Port is 1/2 inch NPT
Discharge Port is 1/2 inch NPT
Positive Displacement, Internal Rotary Gear Design
Open Flow at 1800 RPM : 3.0 GPM at 1800 RPM
Standard Discharge Pressure: up to 500 PSI
Inlet Pressure: up to 280 PSI
Maximum Differential Pressure: 300 PSI
Temperature: up to 375 F
Typical Viscosity Range: 40 to 1000 SSU
|
724.80 |
|
|
Calpeda BCM22/A Motor and Pump
Calpeda's BC-series monobloc centrifugal pumps are complete with open impeller. Available in either cast iron or bronze, single-phase or three-phase.
Close-coupled centrifugal electric pumps with open impeller.
Backward (vortex) impeller for type C 16/1E.
C: version with cast iron pump body and fitting.
B-C: version with bronze pump body and fitting.
Bronze pumps are supplied fully painted.
For liquids moderately charged with impure emulsions.
For industry and agriculture.
For Marine AC Water Pump
Liquid temperature from -10 °C to +90 °C.
Ambient temperature up to 40 C.
Total suction lift up to 8 m.
Maximum permissible working pressure: 6 bar.
Maximum size of solids: 4 mm.
Continuous duty.
|
1057.20 |
|
|
Flotec FP5162 Thermoplastic Sprinkler Pump 1 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1
MAXIMUM CAPACITY: 55 GPM
FLOW at 10' LIFT and 30 PSI: 28 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 42 psi
SUCTION PIPE SIZE: 1-1/2" NPT
DISCHARGE PIPE SIZE: 1-1/2" NPT
AMP DRAW (full load): 7.4 amps on 230v / 14.8 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp on 230v / 20 amp on 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
593.25 |
|
|
Calpeda NM25-12B/A Cast Iron Pump
NM 25/12B/A 230/400V 0,55kW 2900rpm
Close-coupled centrifugal pump with electric motor and extended shaft directly connected to the pump.
NM: single-Impeller.
Connections: threaded ports ISO 228/1 (BS 2779).
NM, NMD: version with pump casing and lanter bracket in cast iron.
B-NM, B-NMD: version with pump casing and lanter bracket in bronze (the pumps are supplied fully painted).
For clean liquids without abrasives, which are non-aggressive for the pump materials (solids content up to 0.2%)
For water supply
For heating, air-conditioning, cooling and circulation plants
For civil and industrial applications
For fire fighting applications
For irrigation
|
567.19 |
|
|
March 809 SS HS C Beer Pump
March Pump's 809-SS-HS-C Beer Pump is an American seal-less centrifugal magnetic drive pump ideal for home brewing. It is capable of generating a maximum flow of 7.5 gallons per minute at 3 feet, and its maximum head is 12.1 Feet (or around 5PSI). The standard wet end (the materials that come into contact with the solution) is composed of Stainless Steel, Teflon, Silicone and Ryton/Teflon/Glass. The inlet connection is 0.75 inch male pipe thread, and the outlet is 0.5 inch male pipe thread. The standard motor is a 1 Phase 115V or 230V 0.04 Horsepower fan cooled motor, which can be run on either 50 or 60 hertz (there are performance differences between the hertz options). The 809-SS-HS-C Beer Pump motor has a six foot cord, a plug, and a base. The maximum internal pressure the pump can tolerate is 150PSI, and the maximum liquid temperature is 250 Fahrenheit or 121 Celsius.
Unit System 60Hz 50Hz Max Flow
7.5 GPM
26.4 LPM
Max Head
12.1 FT
2.5 M
Power
.04 HP
.029 KW
Electrical
115V 50/60HZ
Type
Centrifugal Mag Drive
Inlet
3/4"MPT
Outlet
1/2"MPT
Wet End
Stainless Steel (Front and Rear Housing, Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Can handle liquids of 250F
Materials are FDA Food Compliant
With 6 Foot Cord and Plug
Components are UL Recognized
American Made
|
466.37 |
|
|
Flotec FP4312 Thermoplastic Convertible Jet Pump 1/2 HP
Corrosion resistant convertible jet pumps are constructed of rugged fiberglass-reinforced thermoplastic, and assure years of dependable service.
KEY FEATURES
Superior performance at depths to water of 100' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install dual voltage motor preset to 115v - see manual for 230 volt conversion
WARRANTY
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1/2
MAXIMUM CAPACITY: 9 GPM (shallow well setup)
FLOW AT 10' LIFT and 40 PSI: 7.8 GPM (shallow well setup)
MAX LIFT: 25' w/ shallow well jet kit / 70' w/ deep well jet kit
MAX PSI: 62 psi (shallow well setup)
PRESSURE SWITCH SETTING: 30/50
SUCTION PIPE SIZE: 1-1/4"
MINIMUM SUCTION PIPE SIZE: 1-1/4"
DRIVE PIPE SIZE: 1"
DISCHARGE PIPE SIZE: 1"
MINIMUM DISCHARGE PIPE SIZE: 3/4"
AMP DRAW: 9.9 Amps on 115V / 4.95 Amps on 230V
VOLTAGE: 115v/230v, 60 Hz (factory preset to 115v)
RECOMMENDED BREAKER: 15 amp
MAXIMUM WATER TEMPERATURE: 140 F (60 C)
|
516.00 |
|
|
Flotec FP5172 Thermoplastic Sprinkler Pump 1.5 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 1-1/2
MAXIMUM CAPACITY: 67 GPM
FLOW at 10' LIFT and 30 PSI: 45 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 47 psi
SUCTION PIPE SIZE: 1-1/2" NPT
DISCHARGE PIPE SIZE: 1-1/2" NPT
AMP DRAW (full load): 9.6 amps on 230v / 19.2 amps on 115v
VOLTAGE: 230v / 115v , 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 25 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
621.00 |
|
|
Flotec FP5182 Thermoplastic Sprinkler Pump 2 HP
Corrosion-resistant, self priming sprinkler pumps are constructed of rugged, heavy-duty fiberglass-reinforced thermoplastic. Capable of operating up to 30 sprinkler heads.
KEY FEATURES
Superior performance at depths to water of 20' or less
Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance
Ready-to-install 230 volt motor (dual voltage)
Self-priming after pump housing is initially filled (Check Valve or Foot Valve required)
1 year limited warranty
BODY CONSTRUCTION: Thermoplastic
HORSEPOWER: 2
MAXIMUM CAPACITY: 69 GPM
FLOW AT 10' LIFT and 30 PSI: 45 GPM
MAX LIFT: 25'
MAXIMUM PRESSURE: 50 psi
SUCTION PIPE SIZE: 2" NPT
DISCHARGE PIPE SIZE: 2" NPT
AMP DRAW: 12 amps on 230v / 24 amps on 115v
VOLTAGE: 230v / 115v, 60 Hz
RECOMMENDED BREAKER: 15 amp for 230v / 30 amp for 115v
MAXIMUM WATER TEMPERATURE: 140 °F (60 °C)
|
732.96 |
|
|
March 815 PL C Beer Pump
March Pump’s industrial 815-PL-C is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 8 gallons per minute at 3 feet, and its maximum head is 18.6 Feet (8PSI).
At 60Hz
SystemUS Metric
Max Flow8 GPM 30.3 LPM
Max Head18.6 FT 5.7 M
Power0.04 HP 0.029 KW
At 50Hz
USMetric
7.9 GPM30 LPM
13.5 FT4.1 M
0.04 HP0.029 KW
Electrical: 115V 50/60Hz or 230V 50/60Hz
Inlet: 3/8"FPT & 3/4"MPT
Outlet: 1/2"MPT
Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller)
Max Internal Pressure: 50 PSI / 3.4 bar
Max Liquid Temperature: 250 °F / 121 °C
Applications for the 815-PL-C Magnetic Drive Pump include home brewing, hot water systems, solar heating, and fryers.
The 815-PL-C has pumped Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water.
|
332.48 |
|