CDI Electronics For more than 35 years, CDI Electronics has provided value and lowest cost-of-ownership to the marine and motorsport industry. Our commitment is to provide superior ignition and diagnostic solutions to engine users and manufacturers throughout the world. 

FBRS 2884 Battery Replacement Service for PLB-350 C SARLink™ ACR Life Safety equipment batteries should be replaced according to the manufacturers recommendation and instructions to ensure proper functionality. Battery replacement service includes - Complete physical integrity check Pressure test Data transmission test Replacement of seal and o-rings Installation of the new battery  Disposal of the old battery. *Sold as a Service This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

FBRS 2885 Battery Replacement Service for PLB-350 C SARLink™ ACR Life Safety equipment batteries should be replaced according to the manufacturers recommendation and instructions to ensure proper functionality. Battery replacement service includes - Complete physical integrity check Pressure test Data transmission test Replacement of seal and o-rings Installation of the new battery  Disposal of the old battery. *Sold as a Service This product may not be returned to the original point of purchase. Please contact the manufacturer directly with any issues or concerns.

Restores lost power and performance by cleaning clogged fuel injectors using proprietary polyether amine (PEA) detergent technology. Removes deposits that begin to form with every tank of gasoline. Saves gas by keeping fuel injectors clean. Made with highest quality premium PEA and FLA technologies to specifically address and treat the newer direct injection fuel systems in addition to traditional intake-port delivery systems. Provides total system clean-up and keep-clean, fuel lubricity additive, and fuel stabilizer. Increases power and performance, reduces emissions, improves fuel economy prevents rough idle, hesitation and stalling. Helps with cold start-up problems, prevents premature spark plug fouling, reduces deposit-related engine knocking and pinging, helps prevent injector misfire codes. For use with 18-8600 E-GO! Fuel Injector Cleaning Kit. See Shop & Service Equipment section for details.

Micropump GJ-N21.FF2S.C Pump Head C Mount Micropump 82059 GJJN21.FF2S.C  Mag-Drive Gear Pump Head Requires A-Mount compatible Drive 82059 is constructed of Base Material 316SS Gear Material PTFE Shaft Material 316SS

Micropump GA-V23.C8FS.C Pump Head C Mount Micropump Low-flow pump head, pressure-loaded, 0.084 mL/revolution Max Flow Rate (mL/min): 672 Flow Rate (mL/rev): 0.084 Min Flow Rate (mL/min): 12.6 Differential Pressure (PSI): 40 Differential Pressure (bar): 2.8 Max Motor RPM (rpm): 8000 Seal Material: PTFE Body Material: 316 SS Gear Material: Carbon graphite Relief Valve: No Run Dry: Under 30 seconds Duty Cycle Continuous: Yes Particulates: No Max Temperature ( F): 350 Min Temperature ( F): -50 Max Temperature ( C): 177 Min Temperature ( C): -46 Max Viscosity (cP): 100 Model Number: GA-V23.C8FS.C Part Number: 82117

March 815 PL C Beer Pump March Pump’s industrial 815-PL-C is an American seal-less centrifugal magnetic drive pump ideal for applications such as home brewing and hot water systems. It is capable of generating a maximum flow of 8 gallons per minute at 3 feet, and its maximum head is 18.6 Feet (8PSI).   At 60Hz SystemUS                Metric Max Flow8 GPM  30.3 LPM Max Head18.6 FT  5.7 M Power0.04 HP        0.029 KW   At 50Hz USMetric 7.9 GPM30 LPM 13.5 FT4.1 M 0.04 HP0.029 KW   Electrical: 115V 50/60Hz or 230V 50/60Hz Inlet: 3/8"FPT & 3/4"MPT Outlet: 1/2"MPT   Wet End: Polysulfone (Front Housing), Stainless Steel (Rear Housing and Shaft), Teflon (Thrust Washer), Silicone (O-Ring), Ryton/Teflon/Glass (Impeller) Max Internal Pressure: 50 PSI / 3.4 bar Max Liquid Temperature: 250 °F / 121 °C   Applications for the 815-PL-C Magnetic Drive Pump include home brewing, hot water systems, solar heating, and fryers.   The 815-PL-C has pumped Cutting Oils, Ethylene Glycol, Hot Water, Hot Wort and Salt Water.

Ampco Pumps C+114/C+214-BUNA Seal Kit Buna

Groco S-87-C Tie Rod .250 X 15.313  

Groco Ht-3560-C Handle &Amp; Grip  

Groco ARG-501-C Cap, Bronze Bronze Cap For strainers after Sept 1, 2001 (010901) Does not come with O-rings Order O-rings Part #(2-135) & (2-228) Separately

Groco Sp-49-C Pump Body W/Only Insid Thrd  

Groco Arg-1501-C Cover Casting And Label  

Groco S-88-C Sight Glass  

Groco S-84-C Tie Rod Monel .5 X 17.5