BERKELEY ZBR25270, SELF PRIMING SUCTION KIT

Oberdorfer 300B Series Self Priming Centrifugal Pump FEATURES Pump Body: Bronze Ports: 1" NPT Flow: 22 GPM Max Pressure: 15 PSI Max, 35 feet of head Impeller: Centrifugal Shaft Seal: Mechanical Buna Seal Standard, Viton or Teflon Optional Shaft: Stainless Steel Standard, Monel Optional Motor / Drive: Attaches to NEMA C flange jet pump motors with threaded shaft of stainless steel or monel. We can supply additional motors and assemble if required.     APPLICATIONS / CHARACTERISTICS This close coupled style bronze self-priming centrifugal pump is equipped with high quality ball bearings permanently filled with grease for maintenance free operation.  The main shaft seal is a mechanical face type seal of proven reliability.  Unlike positive displacement pumps centrifugal pumps have larger internal clearances as the pressure is generated by centrifugal force and high liquid velocity.  These pumps can handle impurities in the liquid and the flow in the discharge line may be throttled or shut off without the need for a relief valve. FEATURES Self-Priming to 20 Feet Suction Lift Rugged Bronze Construction Ideal for marine service (air conditioning, bilge, and sea water recirculating). O-Ring Housing seal eliminates gasket problems Auxiliary Connections - for convenient priming and draining Multiple Mechanical Shaft Seal Options -for various applications Pump Heads mount to Standard Footed Nema 56J Jet Pump Motors Shafts : 416 Stainless, Nickel Alloy, or 316 Passivated Stainless Multiple motor options including Explosion Proof For Pedestal Style, see 30PB Optional Lifting Handle DRIVE Centrifugal pumps are designed for single rotation and are non reversible.  Standard rotation is counter clockwise looking at the pump inlet port (clockwise facing pump shaft).  Close coupled centrifugal pumps may be driven by a variety of power sources such as electric motors, hydraulic motors or air motors. Self priming centrifugal pumps must be operated in the horizontal position.  LIQUIDS & TEMPERATURES Capacity - Water 60o F - Gallons Per Minute Maximum lift without foot valve is 10 feet. Bronze pumps are suitable for most common liquids in the pH range from 4-11.  If in doubt consult with factory or check the Oberdorfer™ Chemical Resistance Guide booklet.  The temperature limit for bronze pumps is 212F.  Higher temperatures are possible with fluoroelastomer or Polytetrafluoroethylene (PTFE) seals.  Centrifugal pumps are not well suited for pumping viscous liquids.  Viscosities up to 2000 SSu may be handled resulting in reduced performance and efficiency. Pump seal is mechanical carbon face type mated to ceramic wear face for maximum durability. Other seal components are made of Nitrile with low swell characteristics for compatibility with a wide range of liquids including many chemicals and solvents. SUCTION LIFT Up to 22 gallons per minute water flow and suction lift of 15 feet without a foot or check valve (25 foot suction lift using a foot or check valve and a filled inlet line). A 1/2” pipe plug on the tank top is for initial filling of priming chamber and inlet line--pump priming is automatic thereafter.      300B is Oberdorfers - Self Priming Centrifugal Pump Head Only Bronze    

MP Pump 39467, Flomax 100 Series Self-Priming Centrifugal, 1" X 1" Connections The FMX100 self-priming centrifugal pump is constructed of 316 SS for superior corrosion resistance and compatibility with most fluid types. A carbon / ceramic / viton mechanical seal is standard. With a maximum flow of over 55 GPM and pressure capabilities of nearly 60 feet, this rugged self-priming pump is capable of 17 feet suction lift when operating at 3450 RPM. The FMX100 has numerous applications in industries such as: construction, petroleum, diesel exhaust fluid, marine and marine air conditioning, agriculture for biocides and liquid fertilizers, and numerous industrial applications such as brine and calcium chloride. 316SS Self Prime Pump for chemicals, salt water or many other liquids where corrosion is a problem. Marine Boat air conditioning is a big market for these pumps. Model FRX 75-SP is a high performance self-priming 316 stainless steel centrifugal pump.  The O-ring / flapper design enhances the self-priming capability to 12 foot suction lift. Marine ignition protected motors available. 316 Stainless Steel (Investment Cast). 1/8" NPT Fill Port. Originally designed for marine air conditioning installations when the pump mounting location is prone to air-lock or requires a suction lift. Even when a pump is mounted below the waterline an air-lock can occur due to hull motion when the vessel is underway. Pump will purge air from the system and eliminate “Air-Lock; from becoming an irritating issue.; 1" x 1" Self Priming Centrifugal Pump   APPLICATION: Agricultural, Commercial, Industrial, Marine MATERIALS OF CONSTRUCTION: 316 stainless steel FLOW: Up to 55 GPM HEAD FEET: 60' IMPELLER: 4.0" DRIVE OPTIONS: Close Coupled 1 HP TEFC IEC80B34 Motor, Close coupled 3/4HP TEFC IEC80B34 Motor, Engine Mount for 5/8" Shaft, Pedestal Hydraulic SEAL: Type 6A carbon/ceramic/viton DISCHARGE: 1"   SUCTION: 1"

BERKELEY B85604, IMPELLER REPAIR PART KIT SSHM2 Pump Model B82456. Includes (4) Impellers, (4) Diffusers, (2) O-Rings, Mechanical Seal and Locknuts.  

MP Pumps 21353 Flomax 10 Self Priming Centrifugal Pump  Bronze, Pedestal, 6.0" Impeller, 2" x 2"   FLOMAX 10 self-priming centrifugal pumps are capable of creating vacuum sufficient to lift liquids from heights up to 25 feet above the source. Once primed, the pump's built in flapper valve will maintain a full column of liquid in the suction line. A FLOMAX 10 PumPAK is a fully assembled and run tested pump end that can be easily coupled to a number of drivers such as hydraulic motors, 182TC and 184TC frame motors and gas engines. A bearing pedestal is also available for T-frame motor or belt drive. Standard features include stainless steel drive sleeve, stainless steel fasteners, renewable wear plate, and a semi-open dynamically balanced impeller. The FLOMAX series of pumps are commonly used in Industrial, OEM, Agricultural and Marine applications, such as: Bilge Pumps, Auxiliary Fire Pumps, Ballast Transfer Pumps, Wash-down Pumps, Fertilizer and Pesticide Pumps, Applicators & Sprayers, Blending Pumps, Nurse Tanks, Bulk Transfer Pumps and much more.   Renewable wear plate Stainless steel drive sleeve Stainless steel fasteners Up to a 25' suction lift  

Amt 2850-99 Cast Iron 1 1/4" Self Priming Pedestal Pump AMT Self-Priming Centrifugal Pedestal pumps are designed for a wide range of industrial, agricultural and commercial applications. Dual volute design reduces radial load on bearings and motor. Heavy duty cast iron construction with Buna-N seals or stainless steel with Viton® seals. Pumps are fitted with a self-cleaning, semiopen impeller and are coupled to a heavy duty cast iron bearing housing with a CNC machined keyed shaft extension and sealed ball bearings. The pump has been designed for either direct connection or belt drive. The maximum recommended RPM is 4,000. • Cast Iron & Stainless Steel Construction • Buna-N Mechanical Seals on Cast Iron Models • Viton® Mechanical Seals on Stainless Steel Models • Optional Silicon Carbide Mechanical Seals Available • 1-1/4˝, 1-1/2˝ or 2˝ NPT Suction and Discharge Port Sizes • Dual Volute Design Reduces Radial Load on Motors • Maximum Temperature ◆ Buna-N 180° F ◆ Viton® 200° F • Self-Cleaning, Semi-Open Impeller • Heavy Duty Cast Iron Pedestal Drive with Sealed Ball Bearings

Sealed Macerator Self-Priming Macerator Pump with Run-Dry Protection Waste Evacuation The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage. Fish Box and Livewell Tank Evacuation The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties. Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats. Features: Impeller: Jabsco Nitrile compound Macerator: Stainless Steel Cutter reduces particle size to 1/8" maximum. New 4 blade design Seal: Lip Type WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Run-Dry Macerator Waste Pump WASTE EVACUATION The Jabsco 18590 series DC macerator pump unit is the ideal solution for emptying marine holding tanks when not in a discharge restricted area. Self priming to 5ft this pump will empty a typical 30 gallon (115 Liter) holding tank in less than 3 minutes. Duty cycle of the pump is 15 minutes continuous which means a 180 gallon (680 liter) can be emptied in a single operation It is recommended that holding tanks be flushed with several gallons of water after each pump out. This will reduce the possibility of a continued build up of sediment in the tank which could cause a potential blockage. FISH BOX AND LIVEWELL TANK EVACUATION The Jabsco Macerator Pump is the ideal pump for the emptying of Fish box and livewell receptacles. Very often the livewell tank will be above the waterline of the boat, when this is the case gravity can be used to empty the livewell tank. If not installed in this format then it is beneficial to use the Jabsco macerator pump for evacuation due to its self-priming capabilities and also it's grinding properties. Fish boxes are typically mounted into the floor of the vessel and are very often below the waterline or only partially above the waterline. Again the Jabsco Macerator pump has the characteristics that lend themselves to this application. The bait residue particles of ice, fish scales and anything else that could potentially be found in the Fish-Box will be easily passed buy the Jabsco Macerator Pump, and the self priming capabilities are perfect for fish box installations common to many of today's sports fishing boats. Triple sealed motor to prevent both internal and external motor corrosion New Four-bladed chopper reduces clogging Detects the absence of fluid then shuts-off pump before impeller is damaged Sensor provides adequate run-dry period to allow initial priming of the pump Interrupting power supply to the macerator resets the Run-Dry Device Flow rate to 12 gpm Self-priming to 4ft Fitting: Inlet Port: 1-1/2" Hose Barb plus 1-1/2 NPT Discharge Port: 1" Hose Barb WARNING: This product can expose you to chemicals including NICKEL (METALLIC) which is known to the State of California to cause cancer. For more information go to P65Warnings.ca.gov.

Marine Air Conditioning Self-Priming Circulation Pump - 115VAC, 4.5GPM, 50PSI Bypass, Run-Dry Capable EDM Valves Shurflo will keep your air conditioning running. Air locking often occurs when you lower your boat into the water. Pentair Shurflo Self-priming Circulation Pumps help prevent air locking and keep your air conditioning system up and running. Compatible with all types of boats that are trailerable or not constantly in the water. Specifications: 4.5 GPM 115V Self-priming 50 psi bypass EPDM valves Benefits: Designed with automatic demand Operates quietly Includes thermal protection Can run dry without damage Mounts in any position Recommended Accessories for 5/8" Hose: One inlet strainer 255-215 Two 5/8" hose barb swivel elbows 244-3936 One 5/8" straight 244-2936

Self-Priming Dual Blade Macerator Pump - 24VDC, 13GPM Designed specifically for sanitation waste and fish box evacuations, SHURFLO®'s Macerator pump features a premium impeller design with run-dry capability and includes our seamless shell motor with o-ring sealed end bells and a sealed manual turn key. SHURFLO®'s unique dual blade and housing construction ensures problem free pumping, providing superior performance in harsh marine environments. Thermally protected and ignition protected. 1 Year Warranty Specifications: 24 VDC, 13 GPM [49 LPM] 9 Amps (Max.) 1-1/2" [38.1mm] Inlet Barb 1-1/2" [38.1mm] NPT Outlet Port 1" [25.4mm] Barb Dimensions: 10.6" [269mm] x 4.9" [125mm] x 3.8" [97mm]

Pump Self Priming Hand Operated Manual Galley Pump Whale's manual galley pumps are truly design classics. Since the 1960s these manual pumps have been designed, refined and manufactured by our skilled UK based workforce. Narrow mounting base allows installation for use between two sinks. Features Ideal where space is limited Angled spout and adjustable height provide various options for installation Extended spout makes for easy filling of containers Capacity 8 ltrs (2.2 US gals) per minute Narrow mounting base allows installation for use between two sinks Delivers a smooth flow on each stroke Useful as a back-up pump or for a simple freshwater supply pump Suitable for fresh water and saltwater WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

March 0750-0227-0100 Self Priming Reservoir This self priming reservoir is used on the following March Series 4 and Series 5 pumps: AC-4C-MD, BC-4C-MD, BC-4K-MD, AC-5C-MD, TE-5C-MD, and TE-5K-MD

Jabsco 12290 Series Self Priming Pump Phenolic FEATURES Pump Body: Phenolic Plastic Port Size: 5/8" OD for Hose Connections Flow: 5.8 GPM at 10 feet of head Pressure: Up to 13 PSI Impeller: Neoprene, Nitrile or Viton Shaft Seal: Lip Type Shaft: Shaft of Motor (Stainless Steel) Motor: 115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector, Three-prong ground plug.    APPLICATIONS A low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.   Jabsco Self Priming Pump 5/8" Hose Ports 115V ODP Motor Phenolic Head, Neoprene Impeller  

Jabsco 12290 Series Self Priming Pump Phenolic Pump Body: Phenolic Plastic Port Size: 5/8" OD for Hose Connections Flow: 5.8 GPM at 10 feet of head Pressure: Up to 13 PSI Impeller: Neoprene, Nitrile or Viton Shaft Seal: Lip Type Shaft: Shaft of Motor (Stainless Steel) Motor: 115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector Three-prong ground plug    APPLICATIONS A low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.    Jabsco Self Priming Pump 5/8" Hose Ports 115V Totally Enclosed Motor Phenolic Head, Neoprene Impeller  

Jabsco 12290 Series Self Priming Pump Phenolic   FEATURES Pump Body: Phenolic Plastic Port Size: 5/8" OD for Hose Connections Flow: 5.8 GPM at 10 feet of head Pressure: Up to 13 PSI Impeller: Neoprene, Nitrile or Viton Shaft Seal: Lip Type Shaft: Shaft of Motor (Stainless Steel) Motor: 115 Vac, 1/6 hp, 1750 RPM, 60 Hz, relay start and thermal over-load protector, Three-prong ground plug.     APPLICATIONS / CHARACTERISTICS Designed as a low cost pump for: transfers, circulation, spill returns, filtration and filling line use. Easily handles pure solutions, foaming liquids, emulsions, suspended solids and ferments with viscosities less than 500 SSU (120 cp). Because the plastic pump is resistant to corrosion and metallic contamination, it is widely used for pumping photo chemicals, plating compounds, lab solutions, pharmaceuticals, cosmetics, weak acids, alkalies, liquid fertilizers, insecticides, dyes, detergents, waxes and many more.     Jabsco Self Priming Pump 5/8" Hose Ports 115V Totally Enclosed Motor Phenolic Head, Viton Impeller